SAE AS 3510C-2016 CABLE SAFETY KIT CORROSION AND HEAT RESISTANT STEEL UNS S32100.pdf

《SAE AS 3510C-2016 CABLE SAFETY KIT CORROSION AND HEAT RESISTANT STEEL UNS S32100.pdf》由会员分享，可在线阅读，更多相关《SAE AS 3510C-2016 CABLE SAFETY KIT CORROSION AND HEAT RESISTANT STEEL UNS S32100.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD CABLE, SAFETY, KIT, CORROSION AND HEAT RESISTANT STEEL, UNS S32100 AS3510Copyright 2016 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocop

2、ying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED1993-01 REAFFIRMED2012-11 REVIS

3、ED2016-04 THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.C FEDERAL SUPPLY CLASS 5340 5342 AS3510 SHEET 1 OF 3 REV. C PROCUREMENT SPECIFICATION: AS4536 SAE Technical Standards Board Rules providethat: “This reportis published bySAEto advancethe state oftechnicaland engineering sciences. The use of this r

4、eport isentirely voluntary, andits applicability andsuitability for any particularuse, includingany patent infringement arising therefrom,is the soleresponsibility of theuser.”SAE reviews eachtechnical reportatleast every fiveyears atwhichtimeitmay berevised,reaffirmed, stabilized,orcancelled. SAE i

5、nvites yourwrittencomments andsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS3510C RATIONALE THIS LIMITED SCOPE CHANGE REVISES MATERIAL FOR FERRULE AND END FITTING FROM AMS5689 TO AMS5570. FIGURE 1 - SAFETY CABLE-

6、END FITTING AND CABLE FIGURE 2 - FERRULE TABLE 1A - DIMENSIONS A-D PART NUMBER A /5/ INCH (MM) B MAX INCH (MM) C MAX INCH (MM) D INCH (MM) AS3510-01XXX AS3510-02XXX AS3510-03XXX AS3510-04XXX .022-.026 (0.56-0.66) .032-.038 (0.81-0.97) .040-.046 (1.02-1.17) .062-.072 (1.57-1.83) .135 (3.43) .135 (3.4

7、3) .135 (3.43) .190 (4.83) .085 (2.16) .125 (3.18) .125 (3.18) .155 (3.94) .029-.032 (0.74-0.81) .043-.049 (1.09-1.24) .051-.057 (1.30-1.45) .077-.083 (1.96-2.11) CABLE END FITTING CRIMPED ONTO CABLE TO WITHSTAND PULL-OFF LOAD IN TABLE 1B /4/ AEROSPACE STANDARD AS3510 SHEET 2 OF 3 REV. C CABLE, SAFE

8、TY, KIT, CORROSION AND HEAT RESISTANT STEEL, UNS S32100 SAFETY CABLE ASSEMBLY A PER TABLE 1 TABLE 1B - DIMENSIONS E-F PART NUMBER E INCH (MM) F INCH (MM) CABLE TYPE MINIMUM PULL-OFF LOAD POUND (NEWTON) SEE NOTE /10/ AS3510-01XXX AS3510-02XXX AS3510-03XXX AS3510-04XXX .089-.091 (2.26-2.31) .104-.106

9、(2.64-2.69) .104-.106 (2.64-2.69) .149-.151 (3.78-3.84) .087-.095 (2.21-2.41) .156-.164 (3.96-4.17) .156-.164 (3.96-4.17) .245-.255 (6.22-6.48) STRAND 1X7 CABLE 3X7 CABLE 7X7 CABLE 7X19 30 ( 133.4) 70 ( 311.4) 110 ( 489.3) 280 (1245.5) NOTES: 1. MATERIAL: CABLE - AMS5689. HEAT AND CORROSION RESISTAN

10、T STEEL WIRE (UNS S32100) FERRULE AND END FITTING - AMS5570. HEAT AND CORROSION RESISTANT STEEL SEAMLESS TUBING (UNS S32100) 2. PROCUREMENT SPECIFICATION: AS4536. 3. INSTALLATION IN ACCORDANCE WITH AS4536 AND AS567. /4/ CABLE END FITTING SHAPE OPTIONAL, HOWEVER, MUST BE WITHIN SPECIFIED ENVELOPE. /5

11、/ CUT END OF CABLE OR STRAND SHALL BE FUSED TO PREVENT UNRAVELING AND CAN BE UP TO .006 INCH (0.1524 MM) ABOVE ACTUAL MEASURED DIAMETER. HOWEVER, THE MAXIMUM FUSED END DIAMETER SHALL NOT EXCEED .028, .042, .050, OR .076 FOR -01XXX, -02XXX, -03XXX, OR -04XXX RESPECTIVELY. /6/ LENGTH OF CABLE SHALL BE

12、 3.0 INCH (76.2 MM) INCREMENTS; MINIMUM LENGTH AT 6.0 INCH (152.4 MM), MAXIMUM LENGTH AT 24.0 INCH (609.6 MM), .50 (12.7 MM). 7. MARK PART NUMBER AND MANUFACTURER IDENTIFICATION PER AS478 CLASS N. 8. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994. 9. DIMENSIONS ARE IN INCHES, PARENTHESES ARE IN M

13、ILLIMETERS. /10/ PULL-OFF LOAD IN POUND-FORCE, PARENTHESES IN NEWTONS. /11/ EXAMPLE OF A KIT PART NUMBER: FOR .032 INCH (0.8128 MM) NOMINAL DIAMETER SAFETY CABLE AND FERRULE, 9.0 INCHES (228.6 MM) LONG CABLE AND FERRULE (SEE NOTE 12). EXAMPLE OF A SAFETY CABLE PART NUMBER: FOR .032 INCH (0.8128 MM)

14、NOMINAL DIAMETER SAFETY CABLE 9.0 INCHES (228.6 MM) LONG. AS3510 02 09 K IDENTIFIES ITEM AS A KIT (SAFETY CABLE AND FERRULE) 9.0 INCH (228.6 MM) LENGTH OF CABLE (FIGURE 1) SAFETY CABLE ASSEMBLY A PER TABLE 1 DOCUMENT NUMBER AS3510 02 09 C IDENTIFIES ITEM AS A SAFETY CABLE (NO FERRULE) 9.0 INCH (228.

15、6 MM) LENGTH OF CABLE (FIGURE 1) DOCUMENT NUMBER AEROSPACE STANDARD AS3510 SHEET 3 OF 3 REV. C CABLE, SAFETY, KIT, CORROSION AND HEAT RESISTANT STEEL, UNS S32100 EXAMPLE OF A FERRULE PART NUMBER: FOR .032 INCH (0.8128 MM) NOMINAL DIAMETER SAFETY CABLE. 12. FERRULES SHALL BE PACKAGED IN ACCORDANCE WI

16、TH AS4536. 13. DO NOT USE UNASSIGNED PART NUMBERS. 14. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. 15. ASME Y14.5M-1994 IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. 16. SUPERSESSION: AS3510-XXXXL IS CANCELLED DUE TO A PART NUMBER FORMATTING CHANGE. IT IS SUPERSEDED BY AS3510-XXXXK.

17、 17. PRODUCTS SUPPLIED TO THIS SPECIFICATION SHALL BE PACKAGED IN UNITS OF 50 PIECES PER PACKAGE IN ACCORDANCE WITH AS4536. ALL FERRULES SHALL BE SUPPLIED IN A DISPOSABLE MAGAZINE, EACH CONTAINING 50 FERRULES, AND CONFIGURED IN SUCH A MANNER AS TO ALLOW THE CABLE TO ENTER THE FERRULE, AND EXTRACT ON

18、E FERRULE AT A TIME. 18. SAFETY CABLE AND FERRULES MADE TO PREVIOUS REVISION SPECIFICATIONS MAY BE SOLD AND USED UNTIL STOCK IS DEPLETED. 19. MANUFACTURERS ARE REQUIRED TO SUPPLY AS3510-01XXX SAFETY CABLE TO THE .022 TO.026 DIMENSION (TABLE 1A, A) AFTER PUBLICATION OF THIS SPECIFICATION (REVISION B)

19、. 20. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS3510 02 F IDENTIFIES ITEM AS A FERRULE (NO SAFETY CABLE) SAFETY CABLE ASSEMBLY A PER TABLE 1 DOCUMENT NUMBER