JEDEC JESD76-3-2001 Standard Description of 1 5 V CMOS Logic Devices《1 5 V CMOS逻辑设备的标准描述》.pdf

《JEDEC JESD76-3-2001 Standard Description of 1 5 V CMOS Logic Devices《1 5 V CMOS逻辑设备的标准描述》.pdf》由会员分享，可在线阅读，更多相关《JEDEC JESD76-3-2001 Standard Description of 1 5 V CMOS Logic Devices《1 5 V CMOS逻辑设备的标准描述》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、JEDEC STANDARD Standard Description of 1.5 V CMOS Logic Devices JESD76-3 AUGUST 2001 JEDEC SOLID STATE TECHNOLOGY ASSOCIATION NOTICE JEDEC standards and publications contain material that has been prepared, reviewed, and approved through the JEDEC Board of Directors level and subsequently reviewed a

2、nd approved by the EIA General Counsel. JEDEC standards and publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obt

3、aining with minimum delay the proper product for use by those other than JEDEC members, whether the standard is to be used either domestically or internationally. JEDEC standards and publications are adopted without regard to whether or not their adoption may involve patents or articles, materials,

4、or processes. By such action JEDEC does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the JEDEC standards or publications. The information included in JEDEC standards and publications represents a sound approach to product specification

5、and application, principally from the solid state device manufacturer viewpoint. Within the JEDEC organization there are procedures whereby an JEDEC standard or publication may be further processed and ultimately become an ANSI/EIA standard. No claims to be in conformance with this standard may be m

6、ade unless all requirements stated in the standard are met. Inquiries, comments, and suggestions relative to the content of this JEDEC standard or publication should be addressed to JEDEC Solid State Technology Association, 2500 Wilson Boulevard, Arlington, VA 22201-3834, (703)907-7559 or www.jedec.

7、org Published by JEDEC Solid State Technology Association 2001 2500 Wilson Boulevard Arlington, VA 22201-3834 This document may be downloaded free of charge; however JEDEC retains the copyright on this material. By downloading this file the individual agrees not to charge for or resell the resulting

8、 material. PRICE: Please refer to the current Catalog of JEDEC Engineering Standards and Publications or call Global Engineering Documents, USA and Canada 1-800-854-7179, International (303) 397-7956 Printed in the U.S.A. All rights reserved PLEASE! DONT VIOLATE THE LAW! This document is copyrighted

9、 by the Electronic Industries Alliance and may not be reproduced without permission. Organizations may obtain permission to reproduce a limited number of copies through entering into a license agreement. For information, contact: JEDEC Solid State Technology Association 2500 Wilson Boulevard Arlingt

10、on, Virginia 22201-3834 or call (703) 907-7559 JEDEC Standard No. 76-3 Page 1 STANDARD DESCRIPTION OF 1.5 V CMOS LOGIC DEVICES (From JEDEC Board Ballot JCB-01-34, formulated under the cognizance of the JC-40.1 Subcommittee on CMOS/BiCMOS Digital Logic.) 1 Scope This standard defines dc interface par

11、ameters and test loading for a CMOS digital-logic family based on 1.5 V (nominal) power supply levels and 1.5 V input tolerance. The purpose is to provide a standard for 1.5 V nominal supply voltage CMOS logic devices, for uniformity, multiplicity of sources, elimination of confusion, ease of device

12、 specification, and ease of use. 2 Definitions for the purpose of this document Prefixes: Prefixes ”54” or ”74” immediately preceding family name indicate the operating temperature range. For example, 54XXX refers to the Military (MIL) version of devices which are specified over the temperature rang

13、e of -55 C to 125 C. 74XXX refers to the Commercial (COML) version of devices that are specified over -40 C to 85 C. 3 Standard specifications 3.1 Absolute maximum ratings over operating free-air temperature range (unless otherwise noted) (see Note 1): Supply voltage range, VDD . . . . . . . . . . .

14、 . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 V to 2.0 V Input voltage range, VI: Except I/O ports . . . . . . . . . . . . . . . . . . . . . . 0.5 V to VDD + 0.5 V I/O ports (see Note 1, 2) . . . . . . . . . . . . . . . 0.5 V to VDD + 0.5 V Output voltage range, VO (see Note 1 and 2) .

15、. . . . . . . . . . . . . . . . . . 0.5 V to VDD + 0.5 V Input clamp current, IIK (VI VDD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 50 mA Output clamp current, IOK (VO VDD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Voltage range applied to any output

16、in the high-impedance state or power - off state, VO (see Note 1 and 2) . . . . . . . . . . . . . . . . . . 0.5 V to VDD + 0.5 V Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 C to 150 C NOTE 1 Stresses beyond those listed under “absolute maximum

17、ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute maximum-rated conditions for extended periods

18、 may affect device reliability. NOTE 2 This value is limited to 2 V maximum. JEDEC Standard No. 76-3 Page 2 3 Standard specifications (contd) 3.2 Recommended operating conditions (see Note 3): MIN MAX UNIT Operating 1.4 1.6 VDD Supply voltage Data Retention Only (optional spec.) 1 V VIH High-level i

19、nput voltage VDD = 1.4 V to 1.6 V 0.65 VDD VDD + 0.3 V VIL Low-level input voltage VDD = 1.4 V to 1.6 V 0.3 0.35 VDD V VI Input voltage 0 VDD V VO Output voltage 0 VDD V ?t/?v Input transition rise or fall rate (see Note 4) 0 10 ns/V 54 Series 55 125 TA Operating free-air temperature 74 Series 40 85

20、 C NOTE 3 All unused inputs of the device must be held at VDD or GND to ensure proper device operation. NOTE 4 As measured between VIL(max) and VIH(min). 3.3 Electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) (see Note 5): PARAMETER TEST CONDITI

21、ONS VDD MIN MAX UNIT IOH = 100 A 1.4 V 1.2 V VOH IOH = 2 mA VIH = 0.91 V, VIL = 0.49 V 1.4 V 0.75 VDD V IOL = 100 A 1.4 V 0.2 VOL IOL = 2 mA VIH = 0.91 V, VIL = 0.49 V 1.4 V 0.25 VDD V II VI = VDD to GND 1.6 V 10 A IOZ (see Note 6) VO = VDD to GND 1.6 V 10 A IDD VI = VDD or GND IO = 0 1.6 V 20 A NOT

22、E 5 VDD of the sending and receiving devices must track within 0.1 V to maintain adequate dc margins. NOTE 6 For I/O ports, the parameter IOZ includes the input leakage current. JEDEC Standard No. 76-3 Page 3 4 Test circuit and switching waveforms NOTE 1 CL includes probe, and jig capacitance. NOTE

23、2 Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. NOTE 3 All input pulses are supplied by generat

24、ors having the following characteristics: PRR = 10 MHz, ZO = 50 , tr = tf = 2 ns. NOTE 4 The outputs are measured one at a time with one transition per measurement. NOTE 5 tPLZ and tPHZ are the same as tdis. NOTE 6 tPZL and tPZH are the same as ten. NOTE 7 tPLH and tPHL are the same as tpd. From Out

25、put Under Test CL = 15pF (see note 1) MEASUREMENT 3. PULSE DURATION (WIDTH) MEASUREMENTS tW VDD/2 VDD/2 Input VDD/2 tsu th VDD/2 VDD/2 Timing Input Data Input VDD VDD 0 V 0 V MEASUREMENT 4. SETUP AND HOLD TIMES tPLH tPHL VDD/2 VDD/2 VDD/2 VDD/2 Input Output VDD 0 V VOH VOL MEASUREMENT 1. PROPAGATION

26、 DELAY TIMES MEASUREMENT 2. ENABLE AND DISABLE TIMES TEST S1 tpd Open tPLZ/tPZL 2 X VDD tPHZ/tPZH GND 2k 2k Open 2 x VDD GND S1 0 VVDD Output Control Input Output Waveform 2 S1 at GND (see note 2) Output Waveform 1 S1 at 2 x VDD (see note 2) VOL + 0.1 V tPZH tPZL VDD/2 VDD/2 VDD/2 VDD/2 tPHZ VOH 0.1 V tPLZ VDD 0 V JEDEC Standard No. 76-3 Page 4 6 Reference to other applicable JEDEC standards and publications JESD8-11, 1.5 V 0.1 V Power Supply Voltage and Interface Standard for Non-terminated Digital Intergrated Circuits, October 2000.