GSA A-A-3014-2000 STOOLS FILING AND GENERAL PURPOSE STEP STEEL [Superseded GSA A-A-3116 GSA AA-S-700 A GSA AA-S-700 INT AMD 3 GSA AA-S-700 INT AMD 2 GSA AA-S-700 INT AMD 1 GSA AA-S4 A.pdf

《GSA A-A-3014-2000 STOOLS FILING AND GENERAL PURPOSE STEP STEEL [Superseded GSA A-A-3116 GSA AA-S-700 A GSA AA-S-700 INT AMD 3 GSA AA-S-700 INT AMD 2 GSA AA-S-700 INT AMD 1 GSA AA-S4 A.pdf》由会员分享，可在线阅读，更多相关《GSA A-A-3014-2000 STOOLS FILING AND GENERAL PURPOSE STEP STEEL [Superseded GSA A-A-3116 GSA AA-S-700 A GSA AA-S-700 INT AMD 3 GSA AA-S-700 INT AMD 2 GSA AA-S-700 INT AMD 1 GSA AA-S4 A.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、n METRTC May 9,2000 SUPERSEDING A-A-3014 A-A-3 1 16, AA-S-704, AA-S-700A COMMERCIAL ITEM DESCRIPTION STOOLS, FILING AND GENERAL PURPOSE, STEP, STEEL The General Services Administration has authorized the use of this commercial item description as a replacement for A-A-3 1 16, AA- S-704 and AA-S-700A

2、 for all federal agencies. 1. SCOPE 1.1 This description covers requirements for rotary and non-rotary stools for use in filing rooms. 2. CLASSIFICATION 2.1 Types and sizes. The stools shall be of the following types and sizes (minimum), as specified: O Type I - Stools, filing (non-rotary) Size 1 -

3、350 mm high - Figure 1 Size 2 - 660 mm high - Figure 2 Type II - Stool, general-purpose (rotary) - Figure 3 Size 1 - 125 mm adjustable range (685 mm to 785 mm shall be included) Type III - Step Stool, folding steps - Figure 4 Size 1 - 915mm high Size 2 - 602mm high Class 1 - With back Class 2 - With

4、out back Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any other data that may improve this document should be sent to: General Services Administration, Federal Supply Service, National Furniture Center (3FNE-CO), Washington, DC 20406 FSC 71 05 O Provided by IH

5、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-301 4 Type IV - Step stool, caster mounted - Figure 5 Size lower diameter - 381mm Size top diameter - 292mm Size - 342mm high 3. SALIENT CHARACTERISTICS. 3.1 Materials. All materials shall be unused and free from

6、 defects that affect serviceability or appearance of the finished product. 3.1.1 Steel. The steel shall be commercial quality; either hot or cold rolled, and shall be free from rust, scales, or other imperfections. 3.1.2 Casters. The sockets shall be securely attached in accordance with the manufact

7、urers commercial practice. Caster diameter should be the manufacturers commercially available casters. 3.1.3 Glides. The glides must be firmly secured to each leg but may be removed with simple tools for replacement. 3.1.4 Finish. The finish shall be in accordance with the manufacturers commercial p

8、ractice. Colors shall be the manufacturers commercial colors. 3.2 Design. The stools shall be of the general designs illustrated in figures 1 - 5 3.2.1 Legs, Tvue I Stools. The legs shall be constructed of steel tubing or of steel channel formation or in accordance with the manufacturers commercial

9、practice. 3.2.2 TvPe I. size 1 stools. The leg braces shall be located a minimum 100 mm and a maximum 180 mm from the floor. 3.2.2 Tvue I, size 2 stools. The top surface of the foot ring shall be located 400 mm to 450 mm below the top surface of the seat. The foot ring shall extend the entire distan

10、ce between the legs. The foot ring shall be in one piece. The ring may be positioned internally or externally relative to the legs 3.2.3 Tvue II, size 1 rotarv stool. The rotary stool seat shall revolve a full 360 degrees. The stool shall provide seat height adjustment Height adjustment shall be pos

11、itive and non-binding and shall hold the seat at a given position until intentionally changed. The adjustment shall be continuous or incremental. 3.2.4 Tvue III. The step stool shall have two folding steps. The step stools shall have upholstered seats and backs. 2 Provided by IHSNot for ResaleNo rep

12、roduction or networking permitted without license from IHS-,-,-A-A-30 1 4 O 3.2.5 Type IV. The step stool shall have a caster mounted body or frame with two step levels. It shall roll freely on casters when un-weighted and shall become stationary as soon as a weight of not more than 40 pounds is pla

13、ced on either step. 3.3 Workmanship. The workmanship shall be of a quality to produce a strong, safe piece of equipment. The stools shall have evenly spaced and level legs and braces, securely welded or riveted joints, smoothness of finish, and all parts shall be free from sharp or hazardous surface

14、s and edges, or other defects that affect appearance or might affect strength or serviceability. 3.4 Identification marking. Unless otherwise specified, each stool shall be marked in a plain, permanent and inconspicuous manner, with the Federal Stock Numbers, the date of manufacture, the manufacture

15、rs name or trademark of such known character that the source of manufacture may be readily determined. 3.5 Performance. Each unit shall be tested in accordance with the manufacturers standard commercial test method. 4. PRODUCT CONFORMANCE. The products provided shall meet the salient characteristics

16、 of this commercial item description, conform to the producers own drawings, specifications, standards, and quality assurance practices and is the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 5. REGULATORY REQUIREMENT

17、S. The manufacturer is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent possible. 6. PACKAGING. The stools shall be packaged in accordance with the manufacturers standard commercial practice. 7. NOTES 7.1 Orderinp data. Purchasers should select the pre

18、ferred options permitted herein and include the following information in procurement documents. (a) Title, number and date of this document. (b) Finish of frame, fabric, within the manufacturers offered colors (c) Type, size and class required (d) If special marking is required Preparing Activity GS

19、A-FSS 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-N a k 1 M i - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I I: Figure 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-