GSA A-A-2937 A-2002 REAMER HAND ADJUSTABLE《可调式手铰刀》.pdf

《GSA A-A-2937 A-2002 REAMER HAND ADJUSTABLE《可调式手铰刀》.pdf》由会员分享，可在线阅读，更多相关《GSA A-A-2937 A-2002 REAMER HAND ADJUSTABLE《可调式手铰刀》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-2937A April 23,2002 SUPERSEDING November 27,1995 A-A-2937 COMMERCIAL ITEM DESCRIPTION REAMER, HAND, ADJUSTABLE The General Services Administration has authorized the use of this comercial item description by all federal agencies. 1. SCOPE. This commercial item description covers adjustable hand

2、reamers used in reaming hole diameters to specified tolerances. 2. CLASSIFICATION. Not applicable 3. SALIENT CHARACTERISTICS. 3.1 Design. The adjustable hand reamer shall be of the straight-fluted inserted blade type. Adjustable, straight-fluted inserteid blade reameir Beneficial comments, recommend

3、ations, additions, deletions, clarifications, etc. and any other data which may improve this document should be sent to: General Services Administration, Federal Supply Service, Hardware Superstore (GFEE), 1500 E. Bannister Rd Bldg. #6, Kansas City, Missouri 641 3 1. FSC 5110 Provided by IHSNot for

4、ResaleNo reproduction or networking permitted without license from IHS-,-,- I l 3.2 Dimensions and Sizes. A-A-293 7A Nominal Size 8/A 7/A 6/A 51A 4/A 3/A 21A A B C D E F G H I J K* * L* * M* * N* * O* * Range of Expansion Min. In. % 913 2 511 6 11/32 318 13/32 7/16 15/32 17/32 1 9132 21/32 23/32 25/

5、32 27/32 15/16 1-1/16 1-311 6 1-1 1/32 1-1 1/32 1 - 17/32 1-112 1-25/32 1-1311 6 2-3/32 27/32 2-1 5/32 2-314 Max In. 913 2 511 6 11/32 318 13/32 711 6 15/32 1713 2 19/32 21/32 23/32 25/32 27/32 15/16 1-1/16 1-311 6 1-1 1/32 1-1 7/32 1-112 1-25/32 1 - 13-32 2-3/32 2-7/32 2- 15/32 2-314 2-3 1/32 3-1 1

6、/32 Length of Blades * Min. In. 1-1 1/32 1-1 1/32 1-112 1-112 1-112 1-112 1 -5/8 1-112 1-518 2 2 2-114 2-114 2-314 2-314 3 3-118 3-318 3-318 3-112 3-112 4 4 4- 1311 6 4- 1311 6 5-3/16 5-311 6 Max In. 11518 1-518 1-314 1-314 1-718 1-718 1-718 2 2- 1 /8 2- 112 2-314 3 3-112 3-112 3-112 3 -718 4 4- 1 /

7、2 4-112 4-112 4- 1 /2 5 5 5-314 5-314 6-112 6- 1 /2 Length Overall Min In. 3-114 3-112 4 4-112 4- 1 /2 4-314 5 4 4-112 5 5-112 6 6- 1 12 7 7- 1 /4 7-314 8 9 9 13 13 15 15 17 17 19 19 Max In. 3-112 3-314 4- 1 /8 4-318 4-314 5 5-114 5-112 6 6-112 7 7-314 8-112 9 9-314 10-314 11-314 12-314 12-314 14 14

8、 16 16 18 18 20 20 Number Blades 4 Min. 4 4 4 4 4 6 6 6 6 6 6 6 6 6 6 * = Length of blades to be measured between adjusting nuts with the reamer at maximum size * *= Either range is acceptable. However, when provided in sets, the ranges furnished shall be such that complete dimensional coverage is p

9、rovided. (I 3.3 Materials. The body and adjusting nut part of the reamer shall be made of carbon steel and the cutting blades shall be made of high-speed steel. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-2937A 3.4 Construction. The reamer

10、shall be fitted with removable cutting blades that shall be adjustable for reaming holes of any size within the range for which the reamer is designated. The reamer shall have straight, round shanks with square ends. The shanks shall be concentric with the cutting edges within 0.001” total indicator

11、 reading (tir) as measured between centers. The body portion of the reamer shall contain slots for holding the blades. The reamer shall be constructed to permit an adjustment of not less than 0.035” between the minimum and maximum size attainable with any one set of blades. The reamer assembly shall

12、 be capable of reaming round, straight and smooth holes free of chatter marks within any size range. The pilot bushing of the reamer shall have a surface roughness of not more that 25 micro- inches, arithmetical average (aa). 3.5 Blades. The blades shall be accurately machined and ground in sets to

13、properly fit slots provided on the body of the reamer. Tolerances for the length of individual sets of blades shall not exceed plus or minus 0.0025”. The width of the blades shall be uniform and interchangeable for the same size and make of reamer. Cutting surfaces of blades shall be concentric with

14、 the axis of the body in all positions throughout the range of adjustment. An adjusting nut, located at opposite ends of the blades, shall facilitate the adjustment of the blades. Blade ends shall be ground and rounded so that the blade ends do, not damage the adjusting nut, or washer when used.- 3.

15、6 Adiustinn Nuts. Adjusting nuts shall have at least two flat sides, or other suitable means not requiring special tools or wrenches, for the expansion adjustment. 3.7 Hardness, The full length of the cutting edge of the reamer shall be hardened and tempered to a Rockwell “C” Scale value from 61-67

16、per ASTM E18. 3.8 Threads. The reamer shall have fine threads in accordance with FED-STD-H28. 3.9 Interchanaeabilitv. All part shall be designed and manufactured to definite standards, clearances and tolerances in order that any such parts of particular type or model may be replaced, interchanged an

17、d adjusted without modification of the replacement part or any other parts of the unit. 3.10 Identification Markinn. The reamer shall be marked with the manufactures name or identifying symbol, and the state or country of manufacture. All identification markings shall be engraved, etched, molded or

18、indented directly on the items surface in such a manner that it remains clearly legible throughout the life of the item. The reamer blades shall be marked in sets with the reamers nominal size. In addition, the reamer shall be marked with the words “High Speed” or “High Speed Steel” or the correspon

19、ding abbreviation. 4. REGULATORY REQUIREMENTS. 4.1 Recovered Materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal acquisition Regulation (FAR). 4.2 Metric Products. Products manufactured to me

20、tric dimensions will be considered on an equal basis with those manufactured using inch-pound units, provided they fall within the tolerances specified (using conversion tables contained in the latest revision of Federal Standard 376) and all other requirements of this document are met. If a product

21、 is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inch- pound units, a request should be made to the contracting oficer to determine if the product is acceptable. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

22、om IHS-,-,-5. PRODUCT CONFORMANCE. Nominal Size 8/A 7/A 6/A 4/A 3/A , 21A 1A A-A-293 7A i Range of National Stock Expansion Number Min. In. Max In. 114 9/32 51 10-00-289-101 1 9/32 5/16 5110-00-260-1717 5/16 11/32 51 10-00-260-1728 318 13/32 5 1 10-00-260-1 727 13/32 711 6 5 1 10-00-232-6343 7/16 15

23、/32 5 1 10-00-260-1 724 711 6 1/2 51 10-00-268-1235 e 5.1 Product Conformance. The product provided shall meet the salient characteristics of this Commercial Item Description, conform to the producers own drawing, specifications, standards, and quality assurance practices, and be the same product of

24、fered for sale in the commercial market. The government reserves the right to require proof of such conformance. 5.2 Responsibility for Inspection. Unless otherwise specified, the contractor is responsible for the performance of all inspection requirements and may use any commercial facilities (incl

25、uding the contractors own facilities) suitable for performance of the inspection requirements, unless disapproved by the Government. The Government reserves the right to perform any of the inspections deemed necessary to assure the item conforms to the specified requirements. 6. PACKAGING. Preservat

26、ion, packaging and marking shall be as specified in the contract or order. 7. NOTES. This section contains information of a general or explanatory nature that is not mandatory, 7.1 Source of Documents. American Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, PO Box C700, West Consho

27、hocken, PA 19428-2959. Federal Acquisition Regulation (FAR): Government Printing Office, Superintendent of Documents, Washington DC. 2040 1-937 1. General Services Administration, Specification Section (3FP-E), Suite 8 100,470 LEnfant Plaza, S W, Washington, DC 20407. 7.2 Ordering data. Purchasers s

28、hould select the preferred options permitted herein and should include the following information in procurement documents. a. Title, number, and date of Commercial Item Description. b. Nominal size of reamer. c. Packaging requirements. 7.3a. A list of NSNs assigned that correspond to this CID. The l

29、ist may not be indicative of all possible NSNs associated with the CID. National Stock Number I 5 1 10-00-529-20 14 51 10-00-529-2013 I 5 1 10-00-541 -4962 5 1 10-00-260- 1 702 5 1 1 0-00-541 -496 1 5 1 10-00-720-4782 4 Nominal Size E F G H I J K Range of Expansion Min. In. 23/32 25/32 27/32 15/16 1

30、-1/16 1-311 6 1-1 1/32 Max In. 25/32 27/32 15/16 1-1/16 1-3/16 1-11/32 1 - 17/32 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-National Stock Number Nominal Range of National Stock Sue Expansion Number Min. In. I Max In. 7.4 Key words. Reamer, Hand

31、, Adjustable Min. In. 1-25/32 2-3/32 2-15/32 2-7/32 MILITARY INTERESTS: NONE: DoD has no registered interest in revisions and amendments to this Commercial Item Description until further notice. Max In. 2-3/32 2- 15/32 2-31/32 2-314 Nominal Sue M N O 5 1 1 O-00-260-1 705 5 1 10-00-260- 1706 5 1 10-0

32、0-260- 1707 5 1 10-00-260-1 708 5 1 10-00-596-1 152 5 1 10-00-595-9283 51 10-00-947-3853 A 15/32 17/32 5 1 10-00-232-6347 B 17/32 19/32 5 1 10-00-720-4783 C 19/32 2 1/32 5 1 10-00-720-4787 D 21/32 23/32 51 10-00-915-0440 Kit containing sizes 4A-0 Kit containing sizes A-H Kit containing sizes A-O Preparing Activity: GSA-FSS 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-