GSA A-A-2695 B-1996 PEN ROLLERBALL-POINT RETRACTABLE AND NON-RETRACTABLE (REFILLABLE AND NON-REFILLABLE)《可伸缩和不可伸缩滚珠笔(适于再装和不适于在装)》.pdf

《GSA A-A-2695 B-1996 PEN ROLLERBALL-POINT RETRACTABLE AND NON-RETRACTABLE (REFILLABLE AND NON-REFILLABLE)《可伸缩和不可伸缩滚珠笔(适于再装和不适于在装)》.pdf》由会员分享，可在线阅读，更多相关《GSA A-A-2695 B-1996 PEN ROLLERBALL-POINT RETRACTABLE AND NON-RETRACTABLE (REFILLABLE AND NON-REFILLABLE)《可伸缩和不可伸缩滚珠笔(适于再装和不适于在装)》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-2695B W 9999974 0171153 387 Netricl July 01. 1996 Superseding February 1, 1995 A-A-2695B A-A-2695A COMMERCIAL ITEM DESCRIPTION PEN, ROLLERBALL - POINT, RETRACTABLE & NON-RETRACTABLE (REFILLABLE & NON-REFILLABLE) The General Services Administration has authorized the use of this commercial item d

2、escription, by all federal agencies. 1. Scooe: This Commercial Item Description covers various type retractable / non-retractable, refillable / non-refillable rouerbail/ roiler-point pens containing water based ink cartridges, with corrosion resistant balls having points of .2 mm, .3 mm, .5 mm or .7

3、 mm (all point sizes shall have a tolerance off .O5 mm) as specified in the order or contract. 2. Classification: Types: I. - Executive (Non-RetractableRefillable) II. - Retractable (Refillable) III.- Non-Retractable (Non-Refillable) IV. - Roiler-Point (Non-RetractableNon-Refillable) Size: A. - .2 m

4、m (Ultra-Fine) B. - .3 mm (Extra-Fine) C. - .5 mm (Fine) D. - .7 mm (Medium) 3. Salient Characteristics: 3.1. Type I executive rollerball pens shall consist of a screw-on type (upper and lower) barrel a trim band, a pocket clip, a cylindrical ink cartridge, a screwable plastic ink cartridge guide, a

5、nd a metal or plastic protective nose sleeve. Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data which may improve this document should be sent to General Services Administration, Federal Supply Service, Engineering Branch, 26 Federal Plaza, New York, NY 10

6、278. FSC 7520 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-2695B = 9999974 OL7LL54 213 A-A-2695B 3.1.2 The overall length of the pen (with cap in place) shall be 14.0 cm f .3 cm (5.5 inches f .118 inches) and the replaceable ink cartridge sha

7、ll be 1 1 .$ cm i .3 cm (4.5 inches f -118 inches). The pen shall be provided with a cylindrical ink cartridge (sealed), thereby preventing ink fiom escaping in either liquid or vapor form. The replacement cartridges shall be either black or blue ink with a 0.7 mm tr .O5 mm (0.276 inch f .O01 inch )

8、 non-corrosive ball-point as specified in the contract or order. 3.2 Type II retractablehefillable rollerball pens shall consist of barrel with a contoured grip, a replaceable cylindrical ink cartridge with a non-corrosive 0.7 mm (0.276 inches) bail point, a spring and pocket clip. The pocket clip a

9、cts as a locking device when the cartridge is advanced for writing and a release mechanism to retract the cartridge when the pen is not in use, 3.2.1 The overall length of the pen with cap in place shall be 13.8 cm k .2 cm (5.43 inches * .O78 inches). The pen shall be provided with a black ink cartr

10、idge (sealed), thereby preventing ink fi-om escaping in either liquid or vapor form. The replacement cartridges shall be provided in either black or blue ink with a 0.7 mm f .O5 mm (0.276 inch i .O01 inch) ball point size as specified in the contract or order. 3.3 Type III rollerball pens (non-refil

11、lable) shall consist of a barrel, removable cap, a pocket clip, a point containing a non-corrosive ball and other components necessary to ensure compliance with this description. The pens shall be assembled to seal the reservoir, thereby preventing ink fi-om escaping in either liquid or vapor form.

12、3.3.1 The overall length of the pen with cap in place shall be 13.6 cm f .2 cm (5.4 inches k .O78 inches). The pens shall contain inks in colors of black, blue, red, and green with ball sizes of .3 mm, .5 mm, or .7 mm .O5 mm as specified in the order or contract. The pen color shall be designated by

13、 normal commercial practice. 3.4 Type IV rollerpoint pens (non-refillable) shall consist of a barrel, removable cap, pocket clip, a point containing a non-corrosive ball and other components necessary to ensure compliance with this description. The pens shall be assembled to seal the reservoir, ther

14、eby preventing ink fi-om escaping in either liquid or vapor form. 3.4.1 The overall length ofthe pen with cap in place shall be 13.5 cm 5.3 cm (5.38 inches k .118 inches). The pens shall be provided in colors of black and blue with the ball size being .2 mm. f .O5 mm. The pen color (barrel) shall be

15、 designated by normal commercial practice. 3.5 Pens shall write smoothly by hand, and shall be reproducible by office copy machine which employ a visible light source in the reproduction process. ? I 3.6 Manufacturers name, trademark, writing ball size, or current commercial pen marking shall be exh

16、ibited on the pen. Placement of these markings shall be at the option of the manufhcturer, provided they are prominently legible. PAGE A) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Y A-A-2695B 3.7 Shelf Life. Pens shall have a shelf life of eigh

17、teen (1 8) months after delivery and shall be capable of withstanding normal usage, handling, storage and pass the performance characteristics tests as outlined in paragraph 5.3. 3.8 Workmanship. Rollerbail pens shall be designed and assembled, positively sealing the reservoir (and cartridges) to pr

18、event ink leakage in either liquid and vapor form, while being otherwise free from defects and imperfections which may affect appearance and serviceability. 4. Repulatorv Reauirements: The offererkontractor is encouraged to use recovered materials to the maximum extent practicable, in accordance wit

19、h paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. Oualitv Assurance Reauirements: 5.1. Product Conformance. The products provided shall meet the salient characteristics of this commercial item description, conform to the producers own drawings, specifications, standards and quality

20、assurance practices and be the same product offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 5.2 Examination & Testinp. 5.2.1 Suppliers are encouraged to use quality control (QC) techniques that exhibit control over their processes (e

21、.g. (Statistical Process Control) SPC techniques) as defined in American National Standards Institute (ANSI) Zl.l,Z1.2 and Z1.3 / American Society for Quality Control (ASQC) B. 1, B.2 and B.3 that systematically reduce excess variations. Ifused, objective evidence shall be available that demonstrate

22、s overall measurement adequacy techniques and controls. These techniques shali ensure quality levels equal to, or greater than, those cited in applicable technical document or, herein. 5.2.2 End item inspectionhesting may be used by the offerror or the Government representative, as a means to determ

23、ine the effectiveness of the in process quality controls. We in process controls shall not be substituted for end item performance testing they may be used in examining visual and dimensional characteristics. 5.2.3 For those characteristics for which there are no such controls, or for end item perfo

24、rmance test, lot by lot sampling for inspectiodtest shall be required. The sample unit shall be one pen. Sampling shall be in accordance with the American National Standards Institute (ANSI) / American Society for Quality Control (ASQC) 21.4, Sampling Procedures and Tables for Inspection by Attribut

25、es. PAGE 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-2695B 5.2.4 An inspection lot shall consist of all like items submitted for inspection at one time. The inspection level for end product examination (visual and dimensional) shall be S-4

26、with an AQL of 4.0 percent defective. The inspection level for performance testing shall be S-2 with an AQL of 4.0 percent defective. The supplier must provide objective evidence (tests and inspection records) that the presented material meets the requirements of the sampling plan as indicated above

27、. 5.3 Performance Characteristics Tests: Testing shall be perormed on components whenever practical so long as recordkeeping renders adequate traceability. Unless otherwise specified tests shall be conducted in an atmosphere of 295.15 degrees Kelvin & 2 degrees Kelvin temperature (22 degrees Centigr

28、ade & 2 degrees Centigrade) and 60% f 12% in relative humidity. Test paper shall be 25 percent white bond paper having a pH value, average not less than 5.0 with a basis weight of 75 grams per square meter (20 pounds, 17 x 22 - 500). A tolerance of k 5% is allowable. Paper for the Machine Writing Te

29、st shall have an additional requirement of 160 - 140 seconds maximum smoothness on both sides using the Sheffield method per the most current TAPPI T538 test method. Alternately, paper conforming to JCP-0-60 can be used as an alternate source. 5.3.1 Drving Time: Place a sheet of paper on a smooth, f

30、lat surace and partially cover with a second sheet of paper. Place a 200 gram weight on top of the second sheet of paper. Write a five letter word on the exposed portion of the bottom sheet, allow to dry (10) seconds, and immediately draw the top sheet and the weight across the writing at a rate of

31、10 cm per second. The writing shall not be smeared when tested. Examine both sheets for compliance. 5.3.2 Cai, Off: With the cap removed, expose the rollerball writing instrument to the atmospheric conditions specified in the performance characteristics tests for a period of 24 hours. Writeout requi

32、rements shall meet those specified in writing characteristics. 5.3.3 Machine Writing Test: The machine tests shall be conducted on a Anja model W-1OA , Hartley model W 10-4 Contegma or Minitek writing test machines or equivalent capable of testing pens or refills, with the following parameters set:

33、Writing Load: Writing Angle: 0.981 N (1OOgF) to 1.225N (125gF) 75 & 5“ (non varying) 60“ to 90 (continuously varying) 670 cm f 10.0 cm / min. (22 fi / min.) or Writing Speed: Writing Pattern: Ellipse Writing Surface: Polished Stainless Steel Y Provided by IHSNot for ResaleNo reproduction or networki

34、ng permitted without license from IHS-,-,-A-A-2695B The pens shall be written a minimum distance or the types as listed: Type I. - 900 meters (2953 feet): Type H. - 1000 meters (3280 feet): Type III. - 1300 meters (4265 feet) and Type IV. - 900 meters (2953 feet). Smooth writing shaii start within t

35、he first 10 centimeters of the writeout without starvation or fluctuation of the line intensity. Visual defects include blobs, skips, dotting and density variations of line intensity. Actual length of each visual defect shall be totaled for each cartridge for the entire writeout and shall not exceed

36、 1% o the written he. P 6. Packaping: 6.1 Preservation, packing, and marking shall be as specified in the contract or order. 7. Notes: 7.1. Part Identification Number (PIN): The following part identification numbering procedure is for government purposes and does not constitute a requirement for the

37、 contractor. A-A-2695 A 4 Describes an ultra fuie point roller-point II II Types: II I. Executive II II. Retractable II III. Non-Retractable II IV. Roller-Point I Size: pen in accordance with A-A-2695-B. Il A. .2 mm (Ultra-Fine) B. .3 mm (Extra-Fine) C. .5mm(Fiie) D. .7 mm (Medium) 1 7.2 Source of D

38、ocuments. Issues of the following documents, in effect on the date of invitation for bids or request for proposal, form a part of this document to the extent specified herein. 7.2.1 Federal Acquisition Regulation (FAR) may be obtained fiom the Superintendent of Documents, Government Printing Office,

39、 Washington. DC 20402. 7.2.2 ANSI / ASQC 21.4 may be obtained from the American Society for Quaiity Control, PO Box 3005,611 E. Wisconsin Avenue, Milwaukee, W 53201-4606. 7.2.3 JCP-0-60 specifications may be obtained from Chief Paper Procurement Section, MMPP, US Government Printing Office, North Ca

40、pital and H Street, NW, Washington DC 2040 1. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-2695B 7.2.4 Technical Association of the Pulp and Paper Industry (TAPPI). Test method T538 may be obtained fiom TAPPI, Technology ParWAtlanta, P.O. Box

41、105 113, Atlanta, Georgia, 30348. 7.2.5 Federal Standards and Specifications may be obtained from the General Services Administration Specifications Section (3FB-W) in Suite 8100 at 490 LEnfant Plaza, SW Washington DC 20407. 7.3 National Stock Number Listing (NSNs. The following is a list of NSNs as

42、signed which correspond to this CID. The list may not be indicative of all possible NSNs associated with the CID. Pen, Rollerbail mon-Refillable) 7520-0 1-207-4264 7520-0 1-207-4265 7520-01-207-4266 7520-0 1-207-4267 7520-0 1-207-4268 7520-0 1-207-4269 7520-0 1-207-4270 7520-0 1-207-4271 MILITARY IN

43、TERESTS: NONE: DoD has no registered interest in revisions and amendments to this Commercial Item Description until fiirther notice. Pen, Rollerball Executive Pen, Rollerball (Refillable) RetractableRefiUable Refill. Rollerball Executive Refill, Rollerball 7520-01-424-486 1 7520-01-424-4862 75 10-01-425-5709 75 10-01-425-5703 75 10-01-425-5710 75 10-0 1-425-571 6 Pen, Roller-Point mon-Refillable) 7520-0 1-349-6302 7520-0 1-349-6303 Preparing Activity: GSA-FSS Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-