GMKOREA EDS-T-4534-2011 Test Procedure of Slider Stopper Impact Strength.pdf

《GMKOREA EDS-T-4534-2011 Test Procedure of Slider Stopper Impact Strength.pdf》由会员分享，可在线阅读，更多相关《GMKOREA EDS-T-4534-2011 Test Procedure of Slider Stopper Impact Strength.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING STANDARDS Test Procedure SUPERCEDED EDS-T-4534 Test Procedure of Slider Stopper Impact Strength This standard may be applied only for current projects. It is Superceded for all future projects and replaced by GMW14518. Slider Stopper I$ 4G 98 88x 7 , F6* 72T8p) F$ . 1.1 +95 . Seat Slide

2、r8 98$ -C G$8 Stopper I$ G88x +958p) F$ . 1.2 957 -88 . Slider d#8 8# +& seat7 957F$ . 2 4) E:4 / :0 : C-H +d%P 9I8 6# F 48 07 38%P E:48x 957F$ . 2.1 17 E:4 / . None 2.2 GM E:4 / . None 2.3 dA E:4 / . None 3 4G 88 3.1 4G 8/x . 3.1.1 Seat* 9IF 3L 8# Jig. 3.1.2 3LD 9I-L D# DDD . 3.1.3 Weight (80 Kg),

3、Weight (64 Kg). 3.1.4 $*( . 3.1.5 Wire. 3.2 4G D . 4E ASSY 1B8 Seat* 3P 81 4G F$ . GM KOREA ENGINEERING STANDARDS EDS-T-4534 Copyright 2011 General Motors Company All Rights Reserved September 2011 Page 2 of 3 Version : 3 4 Procedures 4.1 Conditions. 4.1.1 Test Conditions. Deviations from the requir

4、ements of this standard shall have been agreed upon. Such requirements shall be specified on component drawings, test certificates, reports, etc. 4.2 Instructions. 4.2.1 Fix the seat onto the jig and fix the seat fixture jig onto the groove plate so that the seat slider lies horizontal. 4.2.2 Fix th

5、e seat operating parts to design standard points. 4.2.3 Place 64 Kg weight on the seat cushion. 4.2.4 Fix the cushion frame and weight to both ends of the wire and install it onto the pulley for free-falling as shown in Figure 1. 4.2.5 After releasing the slide lock, place and fix the slide to the s

6、lide endmost point. 4.2.6 Remove the fixed force to free-fall 80Kg weight. 4.2.7 Apply impact load to the slider stopper by moving the slide along the operating section through weight free-falling. 4.2.8 After conducting 4.2.5 and 4.2.6, 3 times, check the front slider stopper. 4.2.9 After conductin

7、g 4.2.5, 4.2.6 and 4.2.7 in the opposite direction, check the end slider stopper. 4 4G 9 G$7 88? G 9I4A$ . 4.2.6 9I%P H8x 9PF7 80 Kg Weight * ,h* 88T!F 4A$ . 4.2.7 Weight 8 !F 2$) Slider 8% 88x 8% 4P Slider Stopper7 F:E8x 84 F$ . 4.2.8 4.2.5 7t 4.2.68x 3G 44F G 98$ Slider Stopper* G8 F$ . 4.2.9 -L$4

8、 -F8p) 4.2.5, 4.2.6 0 4.2.7 8x 44 F7 G$ Slider Stopper* G8 F$ . Figure 1 / ,* 1 GM KOREA ENGINEERING STANDARDS EDS-T-4534 Copyright 2011 General Motors Company All Rights Reserved September 2011 Page 3 of 3 Version : 3 5 Data 5.1 Evaluations. No troubles in the slider stopper adjuster function. 6 Sa

9、fety This standard may involve hazardous materials, operations, and equipment. This standard does not propose to address all the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the appli

10、cability of regulatory limitations prior to use. 7 Notes 7.1 Glossary. Not applicable. 7.2 Acronyms, Abbreviations, and Symbols. Not applicable. 8 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: Test to EDS-T-4534 9 Release and Revisions This standard

11、was originated in May 1998. It was first approved by Engineering Standard Committee in May 1998. It was first published in May 1998. 5 4G $8Bd 5.1 D4 . 4G G Slider Stopper d#7 818 68x . 6 6|987 $4F 7 9 ., E:48t 88G ,p: , 86 , 8/x &%8x E FF 3L 8$ . ., E:48t 87 $4F 170 4)%P +& 6|98 ,l9P8 F8x 9P4F:# 6#

12、$ . &d(2P 17 987 95FF 6|980 I 1B* 9DF , -18 9PF 728 957 7 .* 9IF# 8t ., E:4 1788 =y8 1F8$ . 7 768 9I8 7.1 98,l 76 . F$-1F 68 . 7.2 66 -C dGl . F$-1F 68 . 8 Ed - $* ,l2P! $+ &%72P ., E:48 87%T &# $80 M8 EdF$ . Test to EDS-T-4534 9 9P9I -C P9I 8)Y ., E:48t 1998 “x 5 87 E:4 -Gl4 .7 %L6 , d3TE:41,h7 8F 1998“x 587 38%L6$ . ., E:48t 1998“x 587 ) 9P9I / -PF%L6$ . Issue / P9I8)Y Publication Date / 38 88 Description (Organization) / 9PP9I76 (:04.2P ) 3 SEP 2011 Apply new Engineering Standard Template. Superceded (Interior Subsystem Validation Team) / 4 d3TE:4 64 957 . F9I957 =* (Interior.ED4D4 )