FORD SB1-21B-1988 GLOVE BODY FLAME RETARDANT - WITH ALDURA-TYPE GAUNTLET FLAME RETARDANT REVERSIBLE TERRY CLOTH GAUNTLET GLOVE《阻燃手套 ALDURA型阻燃双面毛圈织物长手套》.pdf

《FORD SB1-21B-1988 GLOVE BODY FLAME RETARDANT - WITH ALDURA-TYPE GAUNTLET FLAME RETARDANT REVERSIBLE TERRY CLOTH GAUNTLET GLOVE《阻燃手套 ALDURA型阻燃双面毛圈织物长手套》.pdf》由会员分享，可在线阅读，更多相关《FORD SB1-21B-1988 GLOVE BODY FLAME RETARDANT - WITH ALDURA-TYPE GAUNTLET FLAME RETARDANT REVERSIBLE TERRY CLOTH GAUNTLET GLOVE《阻燃手套 ALDURA型阻燃双面毛圈织物长手套》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、FORD HANUFACTUR I NG STANDARDS SBl-21B,21C GLOVE BODY FLAAE RETARDANT - WITH ALDIJRA-TYPE GAUNTLET SE-216,tlC JULY, 1988 FLAAE RETARDANT REVERSIBLE TERRY CLOTH GAUNTLET GLOVE Page 1 1. 2. 2.1 2.2 2.3 2.4 2.5. 3. 4. 5. USAGE: The gloves are designed for high heat purposes to protect empioyes hands. T

2、he use of these gloves must be approved by the Plant Safety Activity. SEl-216 Glove Body Flame Retardant - With Aldura-Type Gauntlet SBl-21C Flame Retardant Reversible Terry Cloth Gauntlet Glove AATERI AL: Terry cloth shall be produced from cotton yarn of minimum middling 15/l& (23.7nmn) staple weig

3、hing 32 ounces per square yard. This material to be consserc i al 1 y pioccssed to produce a permanent f 1 ame retardant cloth. red in color, which shall be its distinguishing mark. Flame retardancy of this material will be determined in accordance with the test processes outlined in Ford Laboratory

4、 Test Nethod BN 24-2, pages 3-5. - Gauntlet stock for Sal-218 shall be No.8 white numbered duck 18- ounce weight without sizing. Gauntlet material for SBl-21C shall be the same as the glove body, namely 32-ounce red flame retardant terry cloth. Thread shall be red in color and of 24/4 Sak quality. k

5、terial entering into the manufacture of these gloves must be of such quality as to produce a glove which will be free of dermatitis producing agents and impervious to normal dry cleaning and laundering processes. AlNlAUA SIZES: Tip of middle finger to base of gauntlet shall be 8 inches (2Ognm1) . Wi

6、dth of palm at thumb crotch shall be 5-l/4 inches (133mm) l Gauntlet length shall .be 4-l/2 inches (114rmn). The gauntlet width at the base shall be 5-l/4 inches (133mm) flared to 6 inches (15211s) at the gaunflet top. * CONSTRUCT I ON: Reversible inseam with forge loop side.out. The gauntlet shall

7、have a finished top base with overcast stitching which is banded to glove body inseam with double stitching row. All seams shall be sewn 8 st i tches per i nch . SUPPLIERS RESPONSIBILITY: All material supplied to this standard must be equivalent in ail characteristics to the material upon which appr

8、oval was originally granted, and shall be satisfactory for the intended application. FORD MANUFACTURING STANDARDS SBl-21B,ZlC GLOVE BODY FLAME RETARDANT - WITtl ALDURA-TYPE GAUNTLET SBl-ZlB,ZlC JULY, 1988 FLAAE RETARDANT REVERSIBLE TERRY CLOTH GAUNTLET GLOVE Page 2 6. APPROVAL OF NEW SUPPLERS: 6.1 I

9、 I I i i l 6.2 1 Pricing of gloves from proposed new suppliers should be determined to be cost competitive by Purchasing and Supply Staff prior to obtaining laboratory and shop trail approvals. After the product has been determined to be cost competitive, gloves submitted by new manufacturers to thi

10、s standard and concluded to be cost competitive must have laboratory and shop trial approvals. Recommendations for the addition of new manufacturers to the Aanufacturing Approved Source List (ASL) must be made by the appropriate division standards activity in writing to the Plant Engineering Office. Al 1 supporting data must accompany the written request. The Plant Engineering Office, Aanufacturing Staff, and the Environmental Health and Safety Aanager, Employee Relations Staff, will review requests to determine approval. . .