FORD ESB-M4D37-A-2009 POLYVINYL CHLORIDE (PVC) MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《聚氯乙烯(PVC)成型料 与标准FORD WSS-M99P1111-A一起使用 [使用 FORD WSB-M4D871-A1 FORD WSB-M4D.pdf

《FORD ESB-M4D37-A-2009 POLYVINYL CHLORIDE (PVC) MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《聚氯乙烯(PVC)成型料 与标准FORD WSS-M99P1111-A一起使用 [使用 FORD WSB-M4D871-A1 FORD WSB-M4D.pdf》由会员分享，可在线阅读，更多相关《FORD ESB-M4D37-A-2009 POLYVINYL CHLORIDE (PVC) MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《聚氯乙烯(PVC)成型料 与标准FORD WSS-M99P1111-A一起使用 [使用 FORD WSB-M4D871-A1 FORD WSB-M4D.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2009 07 22 N-STATUS Replaced by WSB-M4D871-A1/A2/A3/A4/A5 Y. Bankowski, NA 2005 01 07 Revised Inserted 3.0; Deleted 3.1, 3.9, 3.10 & 4 1963 06 17 Released SS1-838 ESB-M4D37-A Printed copies are uncontrolled Copyright 2009, Ford Global Technolo

2、gies, LLC Page 1 of 2 POLYVINYL CHLORIDE (PVC) MOLDING COMPOUND ESB-M4D37-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a polyvinyl chloride or copolymer molding compound conforming to the physical properties according to its durometer hardness. 2. APPLICATIO

3、N This specification was released originally for material used for miscellaneous parts, such as pillar caps, door lock knobs, head lamp seals, wheel skirt to fender seals and interior trim items. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers

4、 must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 APPEARANCE (FLTM BI 109-01) The color, pattern, and finish shall match the approved Design Center master sample, or shall be as specified on the engineering drawing. 3.3 PHYSICAL CHARACTERISTICS The pr

5、operties of molded slabs made from production stocks shall conform to the following: *Hardness Tensile Durometer, A Specific Strength, Elongation, Tear Resistance, (ASTM D 2240, Gravity, max MPa, min %, min kN/m, min 15 s delay) (ASTM D 729) (ASTM D 412) (ASTM D 412) (ASTM D 624, Die C) 44 - 55 1.35

6、 850 (5.9) 325 18 55 - 65 1.36 1000 (6.9) 275 21 65 - 75 1.38 1400 (9.7) 250 26 75 - 85 1.41 1500 (10.3) 200 35 80 - 90 1.42 2000 (13.8) 150 44 * Durometer hardness to be specified on engineering drawing. 3.4 DIMENSIONAL STABILITY, change max 1% Test Method: Place sample in mechanical convection ove

7、n for 3 h at 70 C, remove and calculate dimensional change. ENGINEERING MATERIAL SPECIFICATIONESB-M4D37-APrinted copies are uncontrolled Copyright 2009, Ford Global Technologies, LLC Page 2 of 2 3.5 COLD FLEXIBILITY (FLTM BN 102-01, mandrel diameter 4 times sample thickness, 50 x 200 mm samples) Mat

8、erials not subjected to flex in assembly shall withstand -29 C without failure. Materials subjected to flex in assembly shall withstand -34 C without failure. 3.6 FADE (FLTM BN 001-01) Shall not stain, exhibit color tone change or change in hue, in accordance with rating 4 - 5 of the AATCC Gray Scal

9、e for evaluating change in color (10 step) after 120 SFH exposure. Production materials shall exhibit lightfastness qualities equal to or better than the approved sample (based on suppliers test data and test specimens as reviewed by the Textile Section) on file in the Textile Section, Body Material

10、s Engineering Department. Stain and fade requirements apply to parts which are visible and where a stain or fade could be objectionable. 3.7 CONTACT AND MIGRATION STAINING When a section of the production part is placed in direct contact with coated cardboard, leather, rubber, vinyl coated fabric, t

11、extiles or painted metal prepared per FLTM BI 103-02, normally used with the material in an assembly, and is exposed for 120 h in a mechanical convection oven maintained at 82 +/- 3 C, it shall not exhibit excessive contact and/or migration staining, softening, or tackiness of the contact material.

12、Production materials shall exhibit resistance to staining qualities equal to or better than the approved sample (based on suppliers test data and test specimens as reviewed by the Textile Section) on file in the Textile Section, Body Materials Engineering Department. 3.8 FLAMMABILITY, max 100 mm/minute (FLTM BN 024-02, without the lot sampling plan) In addition, the test specimen shall not exhibit any flashing or sudden flaming on either surface in excess of the above maximum value.