ETSI TS 122 034-2016 Digital cellular telecommunications system (Phase 2+) Universal Mobile Telecommunications System (UMTS) High Speed Circuit Switched Data (HSCSD) Stage 1 (V13 0.pdf

《ETSI TS 122 034-2016 Digital cellular telecommunications system (Phase 2+) Universal Mobile Telecommunications System (UMTS) High Speed Circuit Switched Data (HSCSD) Stage 1 (V13 0.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 122 034-2016 Digital cellular telecommunications system (Phase 2+) Universal Mobile Telecommunications System (UMTS) High Speed Circuit Switched Data (HSCSD) Stage 1 (V13 0.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 1Digital cellular telecoUniversal Mobile TelHigh Speed Cir(3GPP TS 22.0TECHNICAL SPECIFICATION122 034 V13.0.0 (2016communications system (Phaelecommunications System (Circuit Switched Data (HSCSDStage 1 .034 version 13.0.0 Release 13GLOBAL SYSTEMOBILE COMMUN16-02) hase 2+); (UMTS); SD); 13)

2、 TEM FOR ICATIONSRETSI ETSI TS 122 034 V13.0.0 (2016-02)13GPP TS 22.034 version 13.0.0 Release 13Reference RTS/TSGS-0122034vd00 Keywords GSM,UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C A

3、ssociation but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

4、print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kep

5、t on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you

6、find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and micro

7、film except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights r

8、eserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned

9、 by the GSM Association. ETSI ETSI TS 122 034 V13.0.0 (2016-02)23GPP TS 22.034 version 13.0.0 Release 13Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly

10、 available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

11、 server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may

12、become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These shoul

13、d be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“

14、, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 122 034 V13.0

15、.0 (2016-02)33GPP TS 22.034 version 13.0.0 Release 13Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology 2g3Foreword . 5g31 Scope 6g32 References 6g33 Abbreviations and definitions 6g33.1 Abbreviations . 6g33.2 Definitions 7g34 Description . 7g34.1 General . 7g34.2 Applica

16、bility . 7g34.3 General Bearer Services . 7g34.4 Parameters to be indicated and negotiated . 7g34.4.1 Call set-up . 7g34.4.1.1 T services 8g34.4.1.2 NT services . 8g34.4.2 Network initiated modification . 8g34.4.2.1 T services 8g34.4.2.2 NT services . 8g34.4.3 User initiated modification . 9g34.4.3.

17、1 T services 9g34.4.3.2 NT services . 9g34.5 Air Interface Resource Allocation 9g34.5.1 Minimum GERAN Air Interface Resource Allocation and Allocation Increment . 9g34.5.2 Flexible Air Interface Resource Allocation 9g34.6 Symmetric and asymmetric connections 9g34.6.1 Symmetric connections . 9g34.6.2

18、 Asymmetric connections. 9g34.6.2.1 Asymmetric air interface connection 9g34.6.2.2 Channel coding asymmetry . 10g34.6.3 Network choice of connection symmetry . 10g34.7 User Equipment/Mobile Equipment requirements . 10g34.8 Mobility Management 10g34.9 Roaming . 10g34.10 Quality of Service . 11g34.10.

19、1 Bit error rate 11g34.10.1.1 GERAN TCH/F Bit Error Rate . 11g34.10.1.2 Overall GBS Bit Error Rate 11g34.10.2 GERAN Radio resource management 11g34.10.3 Call set-up delay . 11g34.10.4 End-to-end delay . 11g34.10.5 Throughput . 11g34.10.6 Network planning and interference levels 11g34.11 Mapping of F

20、NUR to GERAN TCH/F for T services 11g34.12 Mapping of GERAN AIUR to GERAN TCH/F for NT services . 11g34.13 GBS MMI aspects 12g34.14 GBS Subscription aspects 12g34.15 GBS charging aspects . 12g34.16 O and M aspects . 12g34.17 Multislot security aspects . 12g35 Exceptional procedures or unsuccessful o

21、utcome 13g3ETSI ETSI TS 122 034 V13.0.0 (2016-02)43GPP TS 22.034 version 13.0.0 Release 136 Interworking requirements . 13g36.1 Service interworking 13g36.1.1 Interworking with supplementary services . 13g36.1.2 Interworking with other services 13g36.2 Network interworking 13g3Annex A (informative):

22、 Change history . 14g3History 15g3ETSI ETSI TS 122 034 V13.0.0 (2016-02)53GPP TS 22.034 version 13.0.0 Release 13Foreword This Technical Specification has been produced by the 3rdGeneration Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG

23、 and may change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for informa

24、tion; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been inc

25、orporated in the document. ETSI ETSI TS 122 034 V13.0.0 (2016-02)63GPP TS 22.034 version 13.0.0 Release 131 Scope The present document specifies the Stage 1 description of High Speed Circuit Switched Data (HSCSD). HSCSD is a feature that introduce General Bearer Services and a multislot mechanism is

26、 used for user rates that can be achieved with one or more TCH/F. Multislot also defines a flexible use of air interface resources which makes efficient and flexible use of higher user rates feasible. The Multislot mechanism is only applicable to GERAN. At UTRAN radio access parameters used for GBS

27、user data are specified at TS 23.107. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific

28、. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same Release as

29、the present document. 1 3GPP TR 21.905: “Vocabulary for 3GPP Specifications“. 2 3GPP TS 22.002: “Bearer Services (BS) supported by a Public Land Mobile Network (PLMN)“. 3 3GPP TS 22.004: “General on supplementary services“. 4 3GPP TS 405.002: “ Multiplexing and multiple access on the radio path“. 3

30、Abbreviations and definitions 3.1 Abbreviations For the purposes of the present document, the following abbreviations apply: AIUR Air Interface User Rate EDGE Enhanced Data rates for GSM Evolution FNUR Fixed Network User Rate GBS General Bearer Services GERAN GSM/EDGE radio access network HSCSD High

31、 Speed Circuit Switched Data MO Mobile Originated MT Mobile TerminatedNT Non Transparent T Transparent UE User Equipment (same as MS in GSM specifications) Additional abbreviations can be found in TS 22.905 1. ETSI ETSI TS 122 034 V13.0.0 (2016-02)73GPP TS 22.034 version 13.0.0 Release 133.2 Definit

32、ions For the purposes of the present document, the following terms and definitions apply: Fixed Network User Rate: user rate between IWF and the fixed network. Air Interface User Rate: user rate between Mobile Termination and IWF. For T services it is the maximum possible AIUR not including padding.

33、 For NT services it is the maximum possible AIUR. maximum possible GERAN AIUR: highest possible GERAN AIUR that the multiple TCH/F can provide, e.g. 2 TCH/F using TCH/F9.6 provides a maximum possible AIUR of 19,2 kbit/s. padding: fill bits needed to adapt the maximum possible AIUR supported by a giv

34、en number of TCH/F with a given channel coding to a FNUR that is lower than the maximum possible AIUR. 4 Description 4.1 General HSCSD is a feature that introduce General Bearer Services (GBS) and a multislot mechanism is used for user rates that can be achieved with one or more TCH/F. HSCSD also de

35、fines mechanisms for the use of air interface resources which makes efficient and flexible use of higher user rates feasible. The Multislot mechanism is only applicable to GERAN. 4.2 Applicability GBS shall provide flexible ways of supporting GSM Phase 2, T and NT data services and new data services

36、 at the higher rates. Data compression shall be applicable to NT GBS. Supplementary Services applicable to the General Bearer Services are specified at TS 22.004, 3. 4.3 General Bearer Services The General Bearer Services are defined in TS 22.002 2. The General Bearer Services (GBS) consist of two B

37、earer Services, and they are as follows: - asynchronous; - synchronous. 4.4 Parameters to be indicated and negotiated 4.4.1 Call set-up The parameters to be indicated, and negotiated, if applicable, during the call set-up shall include: - FNUR; - GERAN Channel coding(s) acceptable (for the call); -

38、maximum number of GERAN TCH/F (that the mobile user can accept); - wanted AIUR (desired rate that the mobile user wants the network to allocate). The wanted AIUR is applicable to NT services only; - indication if the user initiated modification is required, and if so, the network resource needs; - c

39、hannel coding asymmetry indication. ETSI ETSI TS 122 034 V13.0.0 (2016-02)83GPP TS 22.034 version 13.0.0 Release 13Some of the parameters are only utilised by GERAN. When UTRAN radio access bearer is allocated the values are ignored. The GERAN channel coding(s) acceptable shall be indicated by the m

40、obile at call set-up and is not negotiable. It indicates the GERAN channel coding(s) that may be chosen by the network for the call. The maximum number of GERAN TCH/F shall be indicated at call set-up. It enables the mobile user to limit the number of GERAN TCH/F used and thus to control an essentia

41、l parameter for charging. It sets the upper limit of number of TCH/F that the network may allocate to the mobile. The wanted AIUR (applicable to NT services only) indicates the AIUR that the mobile user wants and which the network shall try to reach but which it is not allowed to exceed. The excepti

42、on where the network is allowed to exceed the wanted AIUR is when the network can achieve the GERAN AIUR with a lower number of TCH/F, e.g. wanted GERAN AIUR indicated by the mobile is 14,4 kbit/s, GERAN channel codings acceptable are both TCH/F9.6 and TCH/F4.8 and maximum number of TCH/F are 3, the

43、n the network shall choose 2 x 9,6 over 3 x 4,8 if a channel coding of TCH/F9.6 is available on two TCH/F. If the user wishes to make use of the user initiated modification procedure, this shall be indicated at the call set-up. It shall be possible to reserve a different FNUR than the AIUR. Channel

44、coding asymmetry indication is only applicable to NT calls where the user has indicated acceptance for channel coding(s) based on enhanced modulation. In this case the user may indicate preference for channel coding symmetry, downlink biased channel coding asymmetry, or uplink biased channel coding

45、asymmetry. The channel coding asymmetry indication is only applicable in direction UE to network. 4.4.1.1 T services The ME or the network may propose to modify the FNUR. The calling entity may accept or release the call. Autobauding is not allowed. The AIUR is always equal to the FNUR. Fax Group 3

46、can make use of HSCSD. The GERAN channel coding selected must be one of the channel coding(s) indicated in the channel coding(s) acceptable parameter, the number of TCH/F selected shall not exceed the maximum number of TCH/F parameter, and the combination of the two shall result in an AIUR that is e

47、qual to the FNUR. 4.4.1.2 NT services The ME or the network may propose to modify the FNUR. The calling entity may accept or release the call. Autobauding is allowed. The wanted AIUR is indicated by the mobile at call set-up. 4.4.2 Network initiated modification 4.4.2.1 T services For transparent ca

48、lls the radio resource parameters must remain within limits that allow the transparent call to maintain it is characteristics of fixed end to end throughput and delay. This means that in GERAN the channel coding and the number of TCH/F used may change during the call as long as a channel coding indi

49、cated in the channel coding(s) acceptable parameter is used, the maximum number of TCH/F is not exceeded and the AIUR is kept constant. 4.4.2.2 NT services For NT calls the network may modify the number of TCH/F and the channel coding used at GERAN and thus also the AIUR during the call as long as the maximum number of TCH/F, and the channel coding(s) acceptable are all respected. The network shall try to reach the wanted GERAN AIUR indicated, as long as the resource situation allows it. ETSI ETSI TS 122 034 V13.0.0 (2016-02)93GPP TS 22.034 version 13.0.0