ETSI TS 101 852-2-2-2003 Broadband Radio Access Networks (BRAN) HIPERLAN Type 2 Conformance testing for the Cell based Convergence Layer Part 2 UNI Service Specific Convergence Sub_1.pdf

《ETSI TS 101 852-2-2-2003 Broadband Radio Access Networks (BRAN) HIPERLAN Type 2 Conformance testing for the Cell based Convergence Layer Part 2 UNI Service Specific Convergence Sub_1.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 101 852-2-2-2003 Broadband Radio Access Networks (BRAN) HIPERLAN Type 2 Conformance testing for the Cell based Convergence Layer Part 2 UNI Service Specific Convergence Sub_1.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 101 852-2-2 V1.2.1 (2003-07)Technical Specification Broadband Radio Access Networks (BRAN);HIPERLAN Type 2;Conformance testing for the Cell based Convergence Layer;Part 2: UNI Service Specific Convergence Sublayer (SSCS);Sub-part 2: Test Suite Structure andTest Purposes (TSS Essential, or p

2、otentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carri

3、ed out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Project B

4、roadband Radio Access Networks (BRAN). The present document is part 2, sub-part 2 of a multi-part deliverable. Full details of the entire series can be found in part 1, sub-part 1 8. ETSI ETSI TS 101 852-2-2 V1.2.1 (2003-07) 5 1 Scope The present document contains the Test Suite Structure (TSS) and

5、Test Purposes (TP) to test TS 101 763-2 2. The objective of the present document is to provide a basis for conformance tests for Broadband Radio Access Network (BRAN) HIPERLAN type 2 equipment giving a high probability of air interface inter-operability between different manufacturers BRAN HIPERLAN

6、type 2 equipment. The ISO standard for the methodology of conformance testing (ISO/IEC 9646-1 4 and ISO/IEC 9646-2 5) as well as the ETSI rules for conformance testing (ETS 300 406 3) are used as a basis for the test methodology. 2 References The following documents contain provisions which, through

7、 reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest ve

8、rsion applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. 1 ETSI TS 101 763-1 (V1.1.1): “Broadband Radio Access Networks (BRAN); HIPERLAN Type 2; Cell based Convergence Layer; Part 1: Common Part“. 2 E

9、TSI TS 101 763-2 (V1.1.1): “Broadband Radio Access Networks (BRAN); HIPERLAN Type 2; Cell based Convergence Layer; Part 2: UNI Service Specific Convergence Sublayer (SSCS)“. 3 ETSI ETS 300 406: “Methods for Testing and Specification (MTS); Protocol and profile conformance testing specifications; Sta

10、ndardization methodology“. 4 ISO/IEC 9646-1: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concepts“. 5 ISO/IEC 9646-2: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework -

11、Part 2: Abstract Test Suite specification“. 6 ISO/IEC 9646-6: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 6: Protocol profile test specification“. 7 ISO/IEC 9646-7: “Information technology - Open Systems Interconnection - Conformance

12、testing methodology and framework - Part 7: Implementation Conformance Statements“. 8 ETSI TS 101 852-1-1 (V1.2.1): “ Broadband Radio Access Networks (BRAN); HIPERLAN Type 2; Conformance testing for the Cell based Convergence Layer; Part 1: Common part; Sub-part 1: Protocol Implementation Conformanc

13、e Statement (PICS) proforma“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ISO/IEC 9646-7 7 and in TS 101 763-2 2 apply. ETSI ETSI TS 101 852-2-2 V1.2.1 (2003-07) 6 3.2 Abbreviations For the purposes of the present docum

14、ent, the abbreviations given in ISO/IEC 9646-1 4, ISO/IEC 9646-6 6, ISO/IEC 9646-7 7 and TS 101 763-2 2 and the following apply. ASP Abstract Service Primitive AP Access Point BI Invalid Behaviour BO Inopportune Behaviour BV Valid Behaviour CA Capability tests CL Convergence Layer DLC Data Link Cont

15、rol IUT Implementation Under Test MAC Medium Access Control MT Mobile Terminal PDU Protocol Data unit PICS Protocol Implementation Conformance Statement RLC Radio Link Control TP Test Purposes TSS Test Suite Structure 4 Test Suite Structure 4.1 Structure Figure 1 shows the UNI SSCS Test Suite Struct

16、ure (TSS) including its subgroups defined for the conformance testing. Test Suite Protocol group Protocol subgroup Test group CA BV BI BO UNI-AP/ UNI-MT UNI SSCS Association x DLC-Connection x Handover xFigure 1: TSS for Hiperlan 2 UNI SSCS The test suite is structured as a tree with a first level d

17、efined as UNI-AP or UNI-MT representing the protocol group “UNI SSCS part of CBCL for AP and UNI SSCS part of CBCL for MT“. 4.2 Test groups The test groups are organized in three levels. The first level creates one protocol group representing the protocol services. The second level separates the pro

18、tocol services in functional modules. The last level in each branch contains one or more of the standard ISO subgroups CA, BV, BI and BO. 4.2.1 Protocol groups The protocol groups identify the UNI SSCS part procedures as defined in TS 101 763-2 2. 4.2.1.1 UNI SSCS procedures The UNI SSCS procedures

19、group is divided in three functional modules. The first functional module identifies the association control functions. The second functional module identifies the DLC connection functions. The last functional module identifies the handover functions. ETSI ETSI TS 101 852-2-2 V1.2.1 (2003-07) 7 4.2.

20、2 Main test groups The main test groups are the capability group, the valid behaviour group, the invalid behaviour group and the inopportune behaviour group. 4.2.2.1 Capability (CA) tests This test sub group shall provide limited testing of the major IUT capabilities aiming to insure that the claime

21、d capabilities are correctly supported, according to the PICS. 4.2.2.2 Valid Behaviour (BV) tests This test sub group shall verify that the IUT reacts in conformity with TS 101 763-2 2, after receipt or exchange of valid Protocol Data Units (PDUs). Valid PDUs means that the exchange of messages and

22、the content of the exchanged messages are considered as valid. 4.2.2.3 Invalid Behaviour (BI) tests This test sub group shall verify that the IUT reacts in conformity with TS 101 763-2 2, after receipt of a syntactically invalid PDU. 4.2.2.4 Inopportune Behaviour (BO) tests This test sub group shall

23、 verify that the IUT reacts in conformity with TS 101 763-2 2, after receipt of a syntactically correct PDU not expected in the actual message exchange. 5 Test Purposes (TP) 5.1 Introduction 5.1.1 TP definition conventions The TPs are defined following particular rules as shown in table 1. Table 1:

24、TP definition rules TP Id Reference. Initial condition. Stimulus. Expected behaviour. TP Id The TP Id is a unique identifier it shall be specified according to the TP naming conventions defined in the clause below. Reference The reference should contain the references of the subject to be validated

25、by the actual TP (specification reference, clause, and paragraph). Initial condition The condition defines in which initial state the IUT has to be to apply the actual TP. Stimulus The stimulus defines the test event to which the TP is related. Expected behaviour Definition of the events that are ex

26、pected from the IUT to conform to the base specification. ETSI ETSI TS 101 852-2-2 V1.2.1 (2003-07) 8 5.1.2 TP naming conventions The identifier of the TP is built according to table 2. Table 2: TP naming convention Identifier: TP/- = side type AP Access Point MT Mobile Terminal = protocol group ATM

27、 UNI SSCS procedures = functional module AC Association control function DL DLC connection functions HN Handover functions x = Type of testing CA Capability Tests BV Valid Behaviour Tests BI Invalid Behaviour Tests BO Inopportune Behaviour Tests = sequential number (000-999) Test Purpose Number EXAM

28、PLE: TP/MT/ATM/AC/BV-010 is the tenth purpose for the valid behaviour testing of the procedures for association control function of the UNI SSCS implemented at MT side. 5.1.3 Sources of TP definitions All TPs are specified according to TS 101 763-2 2. 5.2 Test purposes for AP 5.2.1 Association contr

29、ol function TP/AP/ATM/AC/CA-000 Reference: TS 101 763-2, clause 6.2 Initial condition: MT_disassociated_from_AP Check that the IUT sends periodically the RBCH_ASSOCIATION message containing the CL-ID identifying the support of the Cell based ATM-Service with UNI signalling and the CL version number.

30、 TP/AP/ATM/AC/CA-001 Reference: TS 101 763-2, clause 6.2 Initial condition: Link_Agreed_or_Encryption_active_or_Authenticated Check that after receiving the RLC_INFO message, the IUT replies to the LT with a RLC_INFO_ACK message containing in the IE, the connection mappings between VCI and and the m

31、atched ATM parameters. 5.2.2 DLC connection functions TP/AP/ATM/DL/CA-000 Reference: TS 101 763-2, clause 6.2.4 Initial condition: MT_Associated_to_AP. Check that after receiving the RLC_SETUP message, the IUT replies to the LT with a RLC_CONNECT message including the DLC connections the MT shall us

32、e. ETSI ETSI TS 101 852-2-2 V1.2.1 (2003-07) 9 5.3 Test purposes for MT 5.3.1 DLC connection functions TP/MT/ATM/DL/CA-000 Reference: TS 101 763-2, clause 6.2.4 Initial condition: MT_Associated_to_AP. Check that when the association process is terminated, the IUT sends a relevant RLC_SETUP message c

33、ontaining the DLCC-IDs and parameters of connections that were indicated in the Mapping IE transferred as part of the association process. 5.3.2 Handover functions TP/MT/ATM/HN/CA-000 Reference: TS 101 763-2, clause 6.3 Initial condition: MT_Associated_to_AP. Network handover process is pending. The

34、 IUT (MT) has terminated the NW signalling process by receiving the relevant message. Check that after termination of the NW signalling process, the IUT initiates the exchange of higher layer information by sending a RLC_INFO message to the LT. the RLC_INFO message shall not contain values other the ones used before the handover was initiated, i.e. re-negotiation of connection parameters cannot takes place. ETSI ETSI TS 101 852-2-2 V1.2.1 (2003-07) 10History Document history V1.1.1 December 2001 Publication V1.2.1 July 2003 Publication