ETSI TS 101 570-5-2012 Electromagnetic compatibility and Radio spectrum Matters (ERM) Interoperability Testing for Maritime Digital Selective Calling (DSC) Radios Part 5 Handheld V_1.pdf

《ETSI TS 101 570-5-2012 Electromagnetic compatibility and Radio spectrum Matters (ERM) Interoperability Testing for Maritime Digital Selective Calling (DSC) Radios Part 5 Handheld V_1.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 101 570-5-2012 Electromagnetic compatibility and Radio spectrum Matters (ERM) Interoperability Testing for Maritime Digital Selective Calling (DSC) Radios Part 5 Handheld V_1.pdf（63页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 101 570-5 V1.1.1 (2012-06) Electromagnetic compatibility and Radio spectrum Matters (ERM); Interoperability Testing for Maritime Digital Selective Calling (DSC) Radios; Part 5: Handheld VHF Class D Test Descriptions Technical Specification ETSI ETSI TS 101 570-5 V1.1.1 (2012-06)2Reference D

2、TS/ERM-TG26-088-5 Keywords DSC, interoperability, maritime, TSS Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR P

3、olicy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This T

4、echnical Specification (TS) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document is part 5 of a multi-part deliverable. Full details of the entire series can be found in part 1 i.1. ETSI ETSI TS 101 570-5 V1.1.1 (2012-06)5

5、1 Scope The present document contains the Test Descriptions (TD) for interoperability testing of the handheld class D DSC radio equipment. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references,

6、 only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any

7、 hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are necessary for the application of the present document. 1 ETSI EN 300 338-5: “Electromagnetic compatibility and Ra

8、dio spectrum Matters (ERM); Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service; Part 5: Handheld VHF Class D DSC“. 2.2 Informative references The followin

9、g referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 ETSI TS 101 570-1: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Interoperability Testing for Maritime Digital Selective Call

10、ing (DSC) Radios; Part 1: Requirements catalogue“. i.2 ETSI EN 300 338-1: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime

11、MF, MF/HF and/or VHF mobile service; Part 1: Common requirements“. 3 Abbreviations For the purposes of the present document, the abbreviations given in EN 300 338-1 i.2 and the following apply: CF (Test) ConFiguration EUT Equipment Under Test TD Test Description TP Test Purpose TSS Test Suite Struct

12、ure ETSI ETSI TS 101 570-5 V1.1.1 (2012-06)64 Test configurations This clause defines all test configurations used. Each test description referes to one or multiple test configurations. It is assumed that the initial state of all the euipment involved in the test configuration is standby, i.e. unles

13、s stated otherwise the pre-test conditions of each test description assume standby mode for the equipment. An arrow connection between devices indicates that these devices are in communication range, i.e. in CFG_6 EUT, QE1 amd QE2 are all in the same communication range. However, QE3 is only in comm

14、unication range with QE2. Class DEUT QE1Class DCF_1Class D Class A VHFCF_2Class D Class B VHFCF_3Class D Class A/B VHFCF_4Class A/B VHFQE2QE2 is not in EUTscommunication rangeCF_5Class DClass A/B VHFClass DQE2 is within EUTscommunication rangeQE3CF_6Class DClass A/B VHFQE2 is within EUTscommunicatio

15、n rangeClass A/B VHF Class DFigure 1: Configurations for Handheld Class D EUT ETSI ETSI TS 101 570-5 V1.1.1 (2012-06)75 Test Suite Structure (TSS) The following table shows the Test Suite Structure contained in the present document. Test Group Test Sub-Group (sub-group ID) VHF Individual Calls (IC)

16、Group Calls (GC) All Ships Calls (ASC) Sending Distress Alerts (SDA) Receiving Distress Alerts (RDA) Non Distress Automated Procedures (NDAP) Other Calls (OC) Interface and other functions (IOF) General test (GEN) Alarms in standby mode (ASM) Alarms when busy (AWB) Standby mode interface functions (

17、SMIF) Each test description is described through a tabular format conforming to the following convention: Interoperability Test Description Identifier: A unique identifier. The test description identifiers are conforming to the TD_DSC_ naming convention, where: is the Test Group ID (VHF / MFHF) is t

18、he Test Sub-Group ID is the sequential number within the test sub-group Summary: Short description of the test objective Configuration: The relevant test configuration, referencing the test set configurations listed in the Annex References: The reference indicates the clauses of the base standard sp

19、ecifications in which the related interoperability requirement is expressed Pre-test conditions: Defines in which initial state the test equipment has to be to apply the actual test description Step Test Sequence Verdict Pass Fail 1 The description of the individual condition to verify or action to

20、perform Yes/No criteria of the outcome of this verification step (if applicable) Yes/No criteria of the outcome of this verification step (if applicable) 2 Final verdict: ETSI ETSI TS 101 570-5 V1.1.1 (2012-06)86 Test Descriptions (TD) 6.1 Individual Calls Interoperability Test Description Identifie

21、r: TD_DSC_VHF_IC_0001 Summary: Sending Individual call - Routine Configuration: CF_1 References: 1, clauses 5.2.2 and 6.6.1 Pre-test conditions: QE1 and EUT in standby on CH:16 QE1 programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On EUT select Call then select Individual - R

22、outine 2 Enter/select MMSI of QE1 3 Verify that menu proposes an Intership Channel Yes No 4 Verify if the proposed channel can be changed Yes No 5 Cause EUT to send the individual call to QE1 6 Verify that QE1 receives the call Yes No 7 Verify that EUT is still on CH:16 Yes No 8 Cause QE1 to send AC

23、K to EUT 9 Verify that EUT switches to the selected channel in step 4 Yes No 10 Verify voice communication on this channel Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_VHF_IC_0002 Summary: Sending Individual call with NACK - Routine Configuration: CF_1 References: 1, cl

24、auses 5.2.2 and 6.6.1 Pre-test conditions: QE1 and EUT in standby on CH:16 QE1 programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On EUT select Call then select Individual - Routine 2 Enter/select MMSI of QE1 3 Verify that menu proposes an Intership Channel Yes No 4 Verify if

25、the proposed channel can be changed Yes No 5 Cause EUT to send the individual call to QE1 6 Verify that QE1 receives the call Yes No 7 Verify that EUT is still on CH:16 Yes No 8 Cause QE1 to send NACK to EUT 9 Verify that EUT does not switch to the selected channel in step 4 Yes No 10 Verify that EU

26、T indicates call failed or similar Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_VHF_IC_0003 Summary: Sending Individual call to a coast station - Routine Configuration: CF_2 References: 1, clauses 5.2.2 and 6.6.1 Pre-test conditions: QE1 and EUT in standby on CH:16 QE1

27、programmed with a Coast Station MMSI Step Test Sequence Verdict Pass Fail 1 On EUT select Call then select Individual - Routine 2 Enter/select MMSI of QE1 3 Verify that menu does not propose a working channel Yes No Final verdict: ETSI ETSI TS 101 570-5 V1.1.1 (2012-06)9Interoperability Test Descrip

28、tion Identifier: TD_DSC_VHF_IC_0008 Summary: Receiving Individual call - Routine Configuration: CF_2 References: 1, clauses 5.2.2 and 6.7.1 Pre-test conditions: QE1 and EUT in standby on CH:16 EUT programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On QE1 select Call then selec

29、t Individual - Routine 2 Enter/select MMSI of EUT 3 Set the proposed channel to CH:72 4 Cause QE1 to send the individual call to EUT 5 Verify that EUT receives the call and displays the proposed channel Yes No6 Verify that EUT displays the MMSI of QE1 Yes No 7 Verify that EUT is still on CH:16 Yes N

30、o 8 Cause EUT to send ACK to QE1 9 Verify that EUT switches to CH:72 Yes No 10 Verify voice communication on this channel Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_VHF_IC_0009 Summary: Receiving Individual call with NACK - Routine Configuration: CF_2 References: 1, c

31、lauses 5.2.2 and 6.7.1 Pre-test conditions: QE1 and EUT in standby on CH:16 EUT programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On QE1 select Call then select Individual - Routine 2 Enter/select MMSI of EUT 3 Set the proposed channel to CH:72 4 Cause QE1 to send the individ

32、ual call to EUT 5 Verify that EUT receives the call and displays the proposed channel Yes No6 Verify that EUT displays the MMSI of QE1 Yes No 7 Verify that EUT is still on CH:16 Yes No 8 Cause EUT to send NACK to QE1 9 Verify that EUT is still on CH:16 Yes No Final verdict: Interoperability Test Des

33、cription Identifier: TD_DSC_VHF_IC_0010 Summary: Receiving Individual call when busy - Routine Configuration: CF_2 References: 1, clauses 5.2.2 and 6.7.1 Pre-test conditions: QE1 and EUT in individual call on CH:72 QE2 programmed with an individual MMSI of EUT Step Test Sequence Verdict Pass Fail 1

34、On QE2 select Call then select Individual - Routine 2 Enter/select MMSI of EUT 3 Cause QE2 to send the individual call to EUT 4 Verify that EUT sounds a self-terminating alarm Yes No 5 Verify that EUT is still on CH:72 Yes No 6 Cause EUT to terminate the individual call 7 Verify that EUT displays un

35、read messages Yes No 8 On EUT select Call then Received Calls and Verify that the call from QE2 is logged Yes NoFinal verdict: ETSI ETSI TS 101 570-5 V1.1.1 (2012-06)10Interoperability Test Description Identifier: TD_DSC_VHF_IC_0011 Summary: Receiving Individual call - Urgency Configuration: CF_2 Re

36、ferences: 1, clauses 5.2.2 and 6.7.1 Pre-test conditions: QE1 and EUT in standby on CH:16 EUT programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On QE1 select Call then select Individual - Urgency 2 Enter/select MMSI of EUT 3 Set the proposed channel to CH:72 4 Cause QE1 to se

37、nd the individual call to EUT 5 Verify that EUT receives the call and displays the proposed channel Yes No6 Verify that EUT sounds the Urgency alarm Yes No 7 Verify that EUT displays the MMSI of QE1 Yes No 8 Verify that EUT is still on CH:16 Yes No 9 Cause EUT to send ACK to QE1 10 Verify that EUT s

38、witches to CH:72 Yes No 11 Verify voice communication on this channel Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_VHF_IC_0012 Summary: Receiving Individual call with NACK - Urgency Configuration: CF_2 References: 1, clauses 5.2.2 and 6.7.1 Pre-test conditions: QE1 and

39、EUT in standby on CH:16 EUT programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On QE1 select Call then select Individual - Urgency 2 Enter/select MMSI of EUT 3 Set the proposed channel to CH:72 4 Cause QE1 to send the individual call to EUT 5 Verify that EUT receives the call

40、and displays the proposed channel Yes No6 Verify that EUT sounds the Urgency alarm Yes No 7 Verify that EUT displays the MMSI of QE1 Yes No 8 Verify that EUT is still on CH:16 Yes No 9 Cause EUT to send NACK to QE1 10 Verify that EUT returns to standby on CH:16 Yes No Final verdict: ETSI ETSI TS 101

41、 570-5 V1.1.1 (2012-06)11Interoperability Test Description Identifier: TD_DSC_VHF_IC_0013 Summary: Receiving Individual call - Safety Configuration: CF_2 References: 1, clauses 5.2.2 and 6.7.1 Pre-test conditions: QE1 and EUT in standby on CH:16 EUT programmed with an individual MMSI Step Test Seque

42、nce Verdict Pass Fail 1 On QE1 select Call then select Individual - Safety 2 Enter/select MMSI of EUT 3 Set the proposed channel to CH:72 4 Cause QE1 to send the individual call to EUT 5 Verify that EUT receives the call, sounds the Safety alarm and displays the proposed channel Yes No6 Verify that

43、EUT displays the MMSI of QE1 Yes No 7 Verify that EUT is still on CH:16 Yes No 8 Cause EUT to send ACK to QE1 9 Verify that EUT switches to CH:72 Yes No 10 Verify voice communication on this channel Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_VHF_IC_0014 Summary: Recei

44、ving Individual call with NACK - Safety Configuration: CF_2 References: 1, clauses 5.2.2 and 6.7.1 Pre-test conditions: QE1 and EUT in standby on CH:16 EUT programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On QE1 select Call then select Individual - Safety 2 Enter/select MMSI

45、 of EUT 3 Set the proposed channel to CH:72 4 Cause QE1 to send the individual call to EUT 5 Verify that EUT receives the call and displays the proposed channel Yes No6 Verify that EUT sounds the Safety alarm Yes No 7 Verify that EUT displays the MMSI of QE1 Yes No 8 Verify that EUT is still on CH:1

46、6 Yes No 9 Cause EUT to send NACK to QE1 10 Verify that EUT returns to standby on CH:16 Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_VHF_IC_0015 Summary: Sending Individual call on a Distress channel Configuration: CF_2 References: 1, clauses 5.2.2 and 6.6.1 Pre-test co

47、nditions: QE1 and EUT in standby on CH:16 QE1 programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On EUT select Call then select Individual - Routine 2 Enter/select MMSI of QE1 3 Verify that menu proposes an Intership Channel Yes No 4 Enter a distress channel as working channel

48、 5 Cause EUT to send the individual call to QE1 6 Verify that EUT does not send the call and indicates a channel selection error Yes NoFinal verdict: ETSI ETSI TS 101 570-5 V1.1.1 (2012-06)126.2 Group Calls Interoperability Test Description Identifier: TD_DSC_VHF_GC_0001 Summary: Sending group call

49、- Routine Configuration: CF_2 References: 1, clause 6.6.1 Pre-test conditions: QE1 and EUT in standby on CH:16 QE1 programmed with a group MMSI Step Test Sequence Verdict Pass Fail 1 On EUT select Call then select Group 2 Enter/select group MMSI of QE1 3 Verify that menu proposes an Intership Channel Yes No 4 Verify if the proposed channel can be changed Yes No 5 Cause EUT to send the group call to QE1 6 Verify that QE1