EN ISO 2286-1-2016 en Rubber- or plastics-coated fabrics - Determination of roll characteristics - Part 1 Methods for determination of length width and net mass《橡胶或塑料涂覆织物整卷特性-第1部分 .pdf

《EN ISO 2286-1-2016 en Rubber- or plastics-coated fabrics - Determination of roll characteristics - Part 1 Methods for determination of length width and net mass《橡胶或塑料涂覆织物整卷特性-第1部分 .pdf》由会员分享，可在线阅读，更多相关《EN ISO 2286-1-2016 en Rubber- or plastics-coated fabrics - Determination of roll characteristics - Part 1 Methods for determination of length width and net mass《橡胶或塑料涂覆织物整卷特性-第1部分 .pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO 2286-1:2016Rubber- or plastics-coatedfabrics Determination of rollcharacteristicsPart 1: Methods for determinationof length, width and net mass (ISO2286-1:2016)BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN ISO 2286-1:2016 BRITISH STANDARDNational fo

2、rewordThis British Standard is the UK implementation of EN ISO 2286-1:2016. It supersedes BS EN ISO 2286-1:1998 which iswithdrawn.The UK participation in its preparation was entrusted to Technical Committee TCI/69, Footwear, leather and coated fabrics.A list of organizations represented on this comm

3、ittee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 85470 5 ICS 59.08

4、0.40 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD

5、NORME EUROPENNE EUROPISCHE NORM EN ISO 2286-1 October 2016 ICS 59.080.40 Supersedes EN ISO 2286-1:1998English Version Rubber- or plastics-coated fabrics - Determination of roll characteristics - Part 1: Methods for determination of length, width and net mass (ISO 2286-1:2016) Supports textiles revtu

6、s de caoutchouc ou de plastique - Dtermination des caractristiques des rouleaux - Partie 1: Mthodes de dtermination de la longueur, de la largeur et de la masse nette (ISO 2286-1:2016) Mit Kautschuk oder Kunststoff beschichtete Textilien - Bestimmung der Rollencharakteristik - Teil 1: Bestimmung der

7、 Lnge, Breite und Nettomasse (ISO 2286-1:2016) This European Standard was approved by CEN on 1 September 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alte

8、ration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language mad

9、e by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Eston

10、ia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDA

11、RDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 2286-1:2016 EBS EN ISO 2286-1:2016EN

12、ISO 2286-1:2016 (E) 3 European foreword This document (EN ISO 2286-1:2016) has been prepared by Technical Committee ISO/TC 45 “Rubber and rubber products” in collaboration with Technical Committee CEN/TC 248 “Textiles and textile products” the secretariat of which is held by BSI. This European Stand

13、ard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2017, and conflicting national standards shall be withdrawn at the latest by April 2017. Attention is drawn to the possibility that some of the elements of this

14、document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 2286-1:1998. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countrie

15、s are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland

16、, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 2286-1:2016 has been approved by CEN as EN ISO 2286-1:2016 without any modification. BS EN ISO 2286-1:2016ISO 2286-1:2016(E)Foreword iv1 Scope . 12 Normative referen

17、ces 13 Terms and definitions . 14 Apparatus . 15 Procedure. 25.1 General . 25.2 Determination of length 25.3 Determination of usable width . 25.4 Determination of net mass . 26 Test report . 2 ISO 2016 All rights reserved iiiContents PageBS EN ISO 2286-1:2016ISO 2286-1:2016(E)ForewordISO (the Intern

18、ational Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has b

19、een established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical sta

20、ndardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accord

21、ance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details

22、of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endors

23、ement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword Supplementary informat

24、ionThe committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses).This second edition cancels and replaces the first edition (ISO 2286-1:1998), which has been technically revised. The changes are as follows: in Clause 2, ISO 2231:

25、1989 has been added; in 5.1, the statement on the atmospheric conditions and relaxation of tension has been incorporated; in 5.2, the allowance of the final length in measurement has been changed; in 5.3 and 5.4, the tolerance has been changed to more flexible; in Clause 6, item b) has been added.IS

26、O 2286 consists of the following parts, under the general title Rubber or plasticscoated fabrics Determination of roll characteristics: Part 1: Methods for determination of length, width and net mass Part 2: Methods for determination of total mass per unit area, mass per unit area of coating and mas

27、s per unit area of substrate Part 3: Method for determination of thicknessiv ISO 2016 All rights reservedBS EN ISO 2286-1:2016INTERNATIONAL STANDARD ISO 2286-1:2016(E)Rubber- or plastics-coated fabrics Determination of roll characteristics Part 1: Methods for determination of length, width and net m

28、assWARNING Persons using this International Standard should be familiar with normal laboratory practice. This International Standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and healt

29、h practices and to ensure compliance with any national regulatory conditions.1 ScopeThis part of ISO 2286 specifies methods of determining the length, width and net mass of a roll of rubber- or plastics-coated fabrics.2 Normative referencesThe following documents, in whole or in part, are normativel

30、y referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 2231:1989, Rubber- or plastics-coated fabrics Standard atmospher

31、es for conditioning and testing3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.3.1usable widthwidth of a coated fabric, excluding the selvedge, which is consistent in its properties, uniformly finished, and free from unacceptable flaws4 Apparatus4.

32、1 Measuring surface, comprising a flat horizontal surface not less than 5 m long and at least as wide as the roll to be examined. Both longitudinal edges of this surface shall be marked off in 1 m lengths. At least one of these lengths, preferably at the end of the surface, shall be marked at 1 cm i

33、ntervals.4.2 Measuring scale, of a length greater than the width of the fabric to be measured, graduated in millimetres.4.3 Balance, accurate to the nearest 100 g. ISO 2016 All rights reserved 1BS EN ISO 2286-1:2016ISO 2286-1:2016(E)5 Procedure5.1 GeneralRecord the atmospheric temperature and the hu

34、midity in which measurement took place together with a statement as to whether the coated fabric was measured directly from the roll or after being allowed to relax tension free.When an environment to control the atmospheric temperature and the humidity is available, it is recommended that coated fa

35、brics are conditioned in an environment complying with the method of conditioning “1” in ISO 2231:1989 for a minimum of 16 h prior to measurement of length, width and net mass. It is also advisable when measuring length or width to unroll the fabric onto a flat surface and to allow the fabric to com

36、e to equilibrium without tension for a minimum of 16 h.5.2 Determination of lengthProceed either as described in the following paragraph of this subclause, or use any other suitable mechanical, electromechanical or photoelectric equipment for measuring coated-fabric length. The alternative means of

37、measurement, however, can be unsuitable for extensible coated fabrics such as those having a knitted substrate.Trim the cut end of the roll so that it is at right angles to the longitudinal axis of the roll, confining the trimming to the minimum necessary to ensure perpendicularity. With the cut end

38、 of the roll coincident with the zero mark on the measuring surface (4.1), unroll the material along the surface in such a manner that no tension is introduced. On reaching the other end of the surface, mark the back of the roll in some suitable way at both edges so that the marks coincide with a pa

39、rticular division of length. Re-roll the length that has been measured. Lay out, free from tension, a further length of the unmeasured part of the roll, and measure from the edge marks, as before. Repeat this process until the end of the roll appears, trimming this as necessary until it is at right

40、angles to the longitudinal axis of the roll, again confining the trimming to the minimum necessary to ensure perpendicularity. Measure the final length to the nearest 100 mm unless otherwise specified between the interested parties.In cases of dispute, this method shall be the referee method.5.3 Det

41、ermination of usable widthWhile the coated fabric is unrolled and free of tension during the measurements described in 5.2, measure, using the measuring scale (4.2), and record, at intervals of 10 m, the usable width of the coated fabric to the nearest 5 mm unless otherwise specified between the int

42、erested parties, ensuring that all measurements of width are taken at right angles to the longitudinal axis of the roll.For rolls less than 20 m long, measure the width at three positions, i.e. near the two ends and in the middle.5.4 Determination of net massUse the balance (4.3) to determine the ma

43、ss of the tube or former upon which the coated fabric was rolled and record the value in grams. Roll the coated fabric on the tube or former. Determine the gross mass of the roll of coated fabric and record the value in grams. Deduct the mass of the tube or former from the gross mass of the roll and

44、 record this figure, to the nearest 100 g unless otherwise specified between the interested parties, as the net mass of the roll.6 Test reportThe test report shall include the following information. In item d), e), and f), use the value when it is specified between the interested parties.a) a refere

45、nce to this part of ISO 2286, i.e. ISO 2286-1;2 ISO 2016 All rights reservedBS EN ISO 2286-1:2016ISO 2286-1:2016(E)b) the atmospheric temperature and the humidity at the time of the measurement;c) a complete description of the coated fabric;d) the length of the roll, in metres, rounded down to the n

46、earest 0,1 m;e) the mean of the recorded widths to the nearest 5 mm, and also the minimum usable width recorded;f) the net mass of the roll, to the nearest 100 g;g) details of the equipment used to measure the length in 5.2;h) details of any deviations from the procedure specified;i) the date of the

47、 determinations. ISO 2016 All rights reserved 3This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Stand

48、ards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge

49、embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BS