EN 60317-0-5-2007 en Specifications for particular types of winding wires Part 0-5 General requirements - Glass-fibre braided resin or varnish impregnated bare or enamelled rectang.pdf

《EN 60317-0-5-2007 en Specifications for particular types of winding wires Part 0-5 General requirements - Glass-fibre braided resin or varnish impregnated bare or enamelled rectang.pdf》由会员分享，可在线阅读，更多相关《EN 60317-0-5-2007 en Specifications for particular types of winding wires Part 0-5 General requirements - Glass-fibre braided resin or varnish impregnated bare or enamelled rectang.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 60317-0-5:2007Specifications for particular types of winding wires Part 0-5: General requirements Glass-fibre braided resin or varnish impregnated, bare or enamelled rectangular copper wireThe European Standard EN 60317-0-5:2007 has the status of a British StandardICS 29.060.10

2、g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 60317-0-5:2007This British Standard was published under the authority of the Standards Policy

3、and Strategy Committee on 28 February 2007 BSI 2007ISBN 978 0 580 50246 0National forewordThis British Standard was published by BSI. It is the UK implementation of EN 60317-0-5:2007. It is identical with IEC 60317-0-5:2007. It supersedes BS EN 60317-0-5:1995 which is withdrawn.The UK participation

4、in its preparation was entrusted to Technical Committee GEL/55, Winding wires.A list of organizations represented on GEL/55 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct appli

5、cation.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARD EN 60317-0-5 NORME EUROPENNE EUROPISCHE NORM January 2007 CENELEC European Committee for Electrotechnical Standardization Comit Europen d

6、e Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60317-0-5:2007 E ICS 29.060.10 Super

7、sedes EN 60317-0-5:1994 + A1:1998 + A2:2000English version Specifications for particular types of winding wires Part 0-5: General requirements - Glass-fibre braided resin or varnish impregnated, bare or enamelled rectangular copper wire (IEC 60317-0-5:2006) Spcifications pour types particuliers de f

8、ils de bobinage Partie 0-5: Prescriptions gnrales - Fil de section rectangulaire en cuivre nu ou maill recouvert dune tresse de fibres de verre imprgnes de rsine ou de vernis (CEI 60317-0-5:2006) Technische Lieferbedingungen fr bestimmte Typen von Wickeldrhten Teil 0-5: Allgemeine Anforderungen - Fl

9、achdrhte aus Kupfer, blank oder lackisoliert und umsponnen mit Glasgewebe, imprgniert mit Harz oder Lack (IEC 60317-0-5:2006) This European Standard was approved by CENELEC on 2006-12-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for

10、 giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three offic

11、ial versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical commi

12、ttees of Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom

13、. EN 60317-0-5:2007 2 Foreword The text of document 55/993/CDV, future edition 2 of IEC 60317-0-5, prepared by IEC TC 55, Winding wires, was submitted to the IEC-CENELEC parallel Unique Acceptance Procedure and was approved by CENELEC as EN 60317-0-5 on 2006-12-01. This European Standard supersedes

14、EN 60317-0-5:1994 + A1:1998 + A2:2000. The main changes from EN 60317-0-5:1994 are to the abbreviations used for the various glass fibre wound winding wires described in the scope of the standard, and provided in Tables 4 and 7. This standard is to be used in conjunction with the EN 60851 series. Th

15、e clause numbers used in this part of EN 60317 are identical with the respective test numbers of EN 60851. In case of inconsistencies between EN 60851 and this part of EN 60317, the latter shall prevail. The following dates were fixed: latest date by which the EN has to be implemented at national le

16、vel by publication of an identical national standard or by endorsement (dop) 2007-09-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2009-12-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60317-

17、0-5:2006 was approved by CENELEC as a European Standard without any modification. _ 3 EN 60317-0-5:2007 CONTENTS INTRODUCTION H5 1 Scope . H6 2 Normative references H6 3 Definitions, general notes on methods of test and appearance H7 3.1 Definitions H7 3.2 General notes on methods of test H7 3.3 App

18、earance H8 4 Dimensions . H8 4.1 Conductor dimensions H8 4.2 Tolerance on conductor dimensions H10 4.3 Rounding of corners . H10 4.4 Increase in dimensions due to the insulation . H10 4.5 Overall dimensions . H11 5 Electrical resistance H11 6 Elongation. H12 7 Springiness . H12 8 Flexibility and adh

19、erence . H12 8.1 Mandrel winding test. H12 8.2 Adherence test . H12 9 Heat shock H13 10 Cut-through . H13 11 Resistance to abrasion H13 12 Resistance to solvents. H13 13 Breakdown voltage H13 14 Continuity of insulation H13 15 Temperature index H13 16 Resistance to refrigerants H13 17 Solderability

20、H14 18 Heat or solvent bonding. H14 19 Dielectric dissipation factor H14 20 Resistance to transformer oil . H14 21 Loss of mass . H14 23 Pin hole test H14 30 Packaging . H14 Annex A (informative) Nominal cross-sectional areas for preferred and intermediate sizes . H15 Annex ZA (normative) Normative

21、references to international publications with their corresponding European publications22 EN 60317-0-5:2007 4 HTable 1 Nominal cross-sectional areas of preferred sizes9 HTable 2 Conductor tolerances . H10 HTable 3 Corner radii H10 HTable 4 Increase in dimensions. H11 HTable 5 Elongation H12 HTable 6

22、 Mandrel diameters H12 HTable 7 Breakdown voltage. H13 HTable A.1 Nominal cross-sectional areas. H15 5 EN 60317-0-5:2007 INTRODUCTION This part of IEC 60317 is one of a series, which deals with insulated wires used for windings in electrical equipment. The series has three groups describing: 1) meth

23、ods of test (IEC 60851); 2) specifications (IEC 60317); 3) packaging (IEC 60264). EN 60317-0-5:2007 6 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 0-5: General requirements Glass-fibre braided, resin or varnish impregnated, bare or enamelled rectangular copper wire 1 Scope This part of

24、IEC 60317 specifies general requirements of glass-fibre braided resin or varnish impregnated, bare or enamelled rectangular copper wire. The range of nominal conductor dimensions is given in the relevant specification sheet. When reference is made to a winding wire according to IEC 60317-39 or IEC 6

25、0317-40 mentioned under Clause 2, the following information is given in the description: reference to IEC specification; nominal conductor dimensions in millimetres (width thickness); grade of coating and glass covering. The coating shall be characterised by the following grades of thickness: - BGL1

26、, bare conductor with 1 braided layer of glass fibre - BGL2, bare conductor with 2 braided layers of glass fibre - grade 1 BGL1, enamelled grade 1 (grade 1) with 1 braided layer of glass fibre (BGL1) - grade 1 BGL2, enamelled grade 1 (grade 1) with 2 braided layers of glass fibre (BGL2) - grade 2 BG

27、L1, enamelled grade 2 (grade 2) with 1 braided layer of glass fibre (BGL1) - grade 2 BGL2, enamelled grade 2 (grade 2) with 2 braided layers of glass fibre (BGL2) 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, o

28、nly the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60317-39, Specifications for particular types of winding wires Part 39: Glass-fibre braided resin or varnish impregnated, bare or enamelled rectangular copper

29、wire, temperature index 180 IEC 60317-40, Specifications for particular types of winding wires Part 40: Glass-fibre braided resin or varnish impregnated, bare or enamelled rectangular copper wire, temperature index 200 IEC 60851 (all parts), Methods of test for winding wires ISO 3, Preferred numbers

30、 Series of preferred numbers 7 EN 60317-0-5:2007 3 Definitions, general notes on methods of test and appearance For the purposes of this document, the following terms and definitions apply: 3.1 Definitions 3.1.1 coating material which is deposited on a conductor or wire by a suitable means and then

31、dried and/or cured 3.1.2 conductor bare metal after removal of the insulation 3.1.3 covering material which is wound, wrapped or braided around a bare or insulated conductor 3.1.4 crack opening in the insulation which exposes the conductor to view at the stated magnification 3.1.5 enamelled wire wir

32、e coated with an insulation of cured resin 3.1.6 grade the range of thickness of the insulation of a wire 3.1.7 insulation coating or covering on the conductor with the specific function of withstanding voltage 3.1.8 nominal conductor dimension designation of the conductor size in accordance with IE

33、C 60317 3.1.9 normal vision 20/20 vision, with corrective lenses, if necessary 3.1.10 winding wire wire used for winding a coil to provide a magnetic field 3.1.11 wire conductor coated or covered with an insulation 3.2 General notes on methods of test All methods of test to be used for this part of

34、IEC 60317 are given in IEC 60851. Where no specific range of nominal conductor dimensions is given for a test, the test applies to all nominal conductor dimensions covered by the specification sheet. EN 60317-0-5:2007 8 Unless otherwise specified, all tests shall be carried out at a temperature from

35、 15 C to 35 C and a relative humidity from 45 % to 75 %. Before measurements are made, the specimens shall be preconditioned under these atmospheric conditions for a time sufficient to allow the specimens to reach stability. The wire to be tested shall be removed from the packaging in such a way tha

36、t the wire will not be subjected to tension or unnecessary bends. Before each test, sufficient wire should be discarded to ensure that any damaged wire is not included in the test specimens. 3.3 Appearance The fibrous covering shall be continuous, and essentially free from blisters and foreign mater

37、ial when examined with normal vision, as wound on the original spool or reel. 4 Dimensions 4.1 Conductor dimensions The dimensions for widths and thicknesses of conductors of winding wires with rectangular cross-section recommended in this standard are taken from the R 20 and R 40 series according t

38、o ISO 3. Preferred sizes are combinations of width and thickness both according to the R 20 series. Intermediate sizes are combinations of width or thickness according to the R 20 series with the other dimension according to the R 40 series. This section covers widths from 2,00 mm up to and includin

39、g 16,00 mm; thicknesses from 0,80 mm up to and including 5,60 mm. For thickness over 5,60 mm up to and including 10 mm and for widths over 16 mm up to and including 25 mm where, for technical reasons, additional sizes may be needed, the R 40 series shall be used. The ratio width/thickness shall be w

40、ithin the specified limits, and combinations of R 40 and R 40 are not allowed in the case of additional sizes. The ratio width/thickness shall be greater than or equal to 1,4:1 and shall not exceed 8:1. The actual values of dimensions are given in Table 1 F1. The nominal cross-sectional areas for pr

41、eferred sizes are given in Table 1 and the nominal cross-sectional areas for intermediate sizes are given in Annex A. 1Dimensions according to R 20 series are printed in larger type. 9 EN 60317-0-5:2007 Table 1Nominal cross-sectionalareas ofpreferredsizesThickness mm0,800,850,900,951,00 1,061,12 1,1

42、81,251,321,401,501,601,701,801,902,002,122,242,362,50 2,652,803,003,153,353,553,754,004,254,504,755,005,305,60Cornerradius*Cornerradius0,5 mmCornerradius0,65 mmCornerradius0,8 mmCornerradius1,0 mm2,00 1,4631,6261,785 2,025 2,2852,5852,12 2,24 1,6551,8422,025 2,294 2,5852,9213,3692,36 2,50 1,8632,076

43、2,285 2,585 2,9103,2853,7854,1372,65 2,80 2,1032,3462,585 2,921 3,2853,7054,2654,6775,2373,00 3,15 2,3832,6612,935 3,313 3,7234,1954,8255,3075,9376,6933,35 3,55 2,7033,0213,335 3,761 4,2234,7555,4656,0276,7377,5898,326 3,75 4,00 3,0633,4263,785 4,265 4,7855,3856,1856,8377,6378,5979.451 10,654,25 4,5

44、0 3,4633,8764,285 4,825 5,4106,0856,9857,7378,6379,71710,70 12,0513,634,75 5,00 3,8634,3264,785 5,385 6,0356,7857,7858,6379,63710,8411,95 13,4515,2017,205,30 5,60 4,3434,8665,385 6,057 6,7857,6258,7459,71710,8412,1813,45 15,1317,0919,3321,546,00 6,30 4,9035,4966,085 6,841 7,6608,6059,86510,9812,2413

45、,7515,20 17,0919,3021,8224,3427,496,70 7,10 6,2166,885 7,737 8,6609,72511,1512,4213,8415,5417,20 19,3321,8224,6627,5431,0934,647,50 8,00 7,785 8,745 9,78510,9912,5914,0415,6417,5619,45 21,8524,6527,8531,1435,1439,1443,948,50 9,00 9,865 11,0412,3914,1915,8417,6419,8021,95 24,6527,8031,4035,1439,6444,

46、1449,549,50 10,0 12,2913,7915,7917,6419,6422,0424,45 27,4530,9534,9539,1444,1449,1455,1410,6 11,2 15,4717,7119,8022,0424,7327,45 30,8134,7339,2143,9449,5455,1461,8611,8 12,5 19,7922,1424,6427,6430,81 34,4538,8343,8349,1455,3961,6469,1413,2 14,0 24,8427,6431,0034,45 38,6543,5549,1555,1462,1469,1477,5

47、415,0 16,0 31,6435,4839,45 44,2549,8556,2563,1471,1479,1488,74*0.5 nominalthicknessW i dth Figure fromR 40series Figure fromR 20series Preferredsize R 20x R 20Nominalcross-section area (mm) Intermediate size R 20x R 40, R 40x R20Nominalcross-section (See Annex A)Dimensionsnotrecommended R 40x R 40Not recommended Ratio width/thickness over 8:1 0,951,00 Not recommended Ratio width/thickness smaller than 1,4:1- EN 60317-0-5:2007 10 4.2 Tolerance on conductor dimensions The conductor dimensions shall not differ from the nominal v