EN 16796-3-2016 en Energy efficiency of Industrial trucks - Test methods - Part 3 Container handling lift trucks《工业卡车的能源效率-试验方法-第3部分 集装箱装卸电梯》.pdf

《EN 16796-3-2016 en Energy efficiency of Industrial trucks - Test methods - Part 3 Container handling lift trucks《工业卡车的能源效率-试验方法-第3部分 集装箱装卸电梯》.pdf》由会员分享，可在线阅读，更多相关《EN 16796-3-2016 en Energy efficiency of Industrial trucks - Test methods - Part 3 Container handling lift trucks《工业卡车的能源效率-试验方法-第3部分 集装箱装卸电梯》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 16796-3:2016Energy efficiency of Industrial trucks Test methodsPart 3: Container handling lift trucksBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 16796-3:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 16796-3

2、:2016. The UK participation in its preparation was entrusted to TechnicalCommittee MHE/7, Industrial trucks.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users

3、 are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 86024 9 ICS 53.060 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of th

4、e Standards Policy and Strategy Committee on 30 November 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 16796-3:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16796-3 November 2016 ICS 53.060 English Version Energy efficiency of Industrial trucks - Tes

5、t methods - Part 3: Container handling lift trucks Efficacit nergtique des chariots de manutention - Mthodes dessai - Partie 3 : Chariots lvateurs porte-conteneur Energie Effizienz von Flurfrderzeugen - Testmethoden - Teil 3: Container Stapler This European Standard was approved by CEN on 13 August

6、2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtaine

7、d on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-C

8、ENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, I

9、taly, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Av

10、enue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16796-3:2016 EBS EN 16796-3:2016EN 16796-3:2016 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitio

11、ns . 4 4 Test conditions . 4 4.1 General 4 4.2 Laden container handler 4 4.3 Empty container handler . 4 5 Measurement procedure 5 5.1 General 5 5.2 Test set-up . 5 5.3 Operating sequence 5 Bibliography 7 BS EN 16796-3:2016EN 16796-3:2016 (E) 3 European foreword This document (EN 16796-3:2016) has b

12、een prepared by Technical Committee CEN/TC 150 “Industrial Trucks - Safety”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2017, and conflicting nati

13、onal standards shall be withdrawn at the latest by May 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. EN 16796 consists of the following parts

14、, under the general title Energy efficiency of Industrial trucks Test methods: Part 1: General; Part 2: Operator controlled self-propelled trucks, towing tractors and burden-carrier trucks; Part 3: Container handling lift trucks. The following parts are under preparation: Part 4: Rough-terrain truck

15、s; Part 5: Trucks with elevating operator position and trucks specifically designed to travel with elevated loads. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulga

16、ria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Tur

17、key and the United Kingdom. BS EN 16796-3:2016EN 16796-3:2016 (E) 4 1 Scope This European Standard specifies the method of energy consumption measurement for container handling lift trucks, as defined in ISO 5053-1. This part is intended to be used in conjunction with EN 16796-1. 2 Normative referen

18、ces The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN

19、16796-1:2016, Energy efficiency of Industrial trucks - Test methods - Part 1: General ISO 668, Series 1 freight containers Classification, dimensions and ratings ISO 5053-1, Industrial trucks Terminology and classification Part 1: Types of industrial trucks ISO 5353, Earth-moving machinery, and trac

20、tors and machinery for agriculture and forestry Seat index point ISO 22915-9:2014, Industrial trucks Verification of stability Part 9: Counterbalanced trucks with mast handling freight containers of 6 m (20 ft) length and longer ISO 22915-12:2015, Industrial trucks Verification of stability Part 12:

21、 Industrial variable-reach trucks handling freight containers of 6 m (20 ft) length and longer 3 Terms and definitions For the purposes of this document the terms and definitions given in ISO 5053-1 and EN 16796-1 apply. 4 Test conditions 4.1 General The travelling position shall be such that the bo

22、ttom of the container is no higher than 0,9 m above the seat index point (SIP) as defined in ISO 5353 (see ISO 22915-9:2014, 4.2 and ISO 22915-12:2015, 4.2), and at a height ensuring that the operator has sufficient forward visibility. In the travelling position the boom shall be fully retracted. Ad

23、ditional requirements for test conditions are given in EN 16796-1. 4.2 Laden container handler A laden container handler shall be tested with a test load of 70 % of the rated load. 4.3 Empty container handler An empty container handler shall be tested with an empty container according to ISO 668. A

24、container with a height of 8 6” and a length of 20 (20 ft) shall be used in the test. (weight of 20 ft container minimum 2 200 kg) BS EN 16796-3:2016EN 16796-3:2016 (E) 5 5 Measurement procedure 5.1 General The appropriate requirements of EN 16796-1:2016, Clause 5 apply together with the following c

25、lauses which describe specific information for container handling lift trucks. 5.2 Test set-up Measurement shall start with the machine loaded and fully supported, with twist locks engaged at the travelling position height, at position A. It is permissible for variable reach container handling truck

26、s to be tested using simultaneous lifting and extension of the boom. Table 1 Test specification for container handling lift trucks Variable reach container handler / Counterbalance container handler Empty container handler Loaded container handler Rated capacity Q Q 10 t Q 10 t Test duration h 1 1 N

27、o. of cycles 1/h 30 20 Distance l m 100 100 Lift at B and D m 4 4 5.3 Operating sequence The cycle shall be performed according to Figure 1 and Table 1. The sequence of the cycle shall be carried out with the following actions: Start at position A (travelling position); travel in forward direction t

28、o position “B” by turning through 90 and advance to position of container stack; return the backward tilt to the vertical position (only Counterbalanced container handler); lift the load as specified in Table 1; lower to the travelling position height; tilt back to maximum (only Counterbalanced cont

29、ainer handler); drive backwards to position “C”; travel in forward direction to position “D” by turning through 90 and advance to position of container stack; return the backward tilt to the vertical position (only Counterbalanced container handler); BS EN 16796-3:2016EN 16796-3:2016 (E) 6 lift the

30、load as specified in Table 1; lower to the travelling position height; tilt back to maximum (only Counterbalanced container handler); drive backwards to position “A”; end of cycle. The travel speed shall be so adapted to reach the specified number of cycles per hour. The load shall be lifted and low

31、ered, without depositing the load. Travelling is not permitted while lift/lowering, or reach/retracting operations. Key A, B, C, D truck position l distance Figure 1 Test layout energy consumption BS EN 16796-3:2016EN 16796-3:2016 (E) 7 Bibliography 1 EN ISO 3691-2, Industrial trucks - Safety requir

32、ements and verification - Part 2: Self-propelled variable-reach trucks (ISO 3691-2) This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorpo

33、rated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into stan

34、dards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can pro

35、vide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted

36、 European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the cont

37、ent in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use

38、.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing

39、 and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and th

40、at only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any for

41、mat to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduc

42、e content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to ove

43、r 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy an

44、d subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benef

45、its of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further inf

46、ormation, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please info

47、rm the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Group Headquarters389 Chiswick High Road London W4 4AL UKBSI Back Cover.indd 1 27/01/2016 14:20