EN 16063-2011 en Packaging - Rigid plastic containers - Nomenclature of plastic finishes《包装 硬质塑料容器 塑料装饰的术语》.pdf

《EN 16063-2011 en Packaging - Rigid plastic containers - Nomenclature of plastic finishes《包装 硬质塑料容器 塑料装饰的术语》.pdf》由会员分享，可在线阅读，更多相关《EN 16063-2011 en Packaging - Rigid plastic containers - Nomenclature of plastic finishes《包装 硬质塑料容器 塑料装饰的术语》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 16063:2011Packaging Rigid plasticcontainers Nomenclature ofplastic finishesBS EN 16063:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation

2、of EN 16063:2011.The UK participation in its preparation was entrusted to TechnicalCommittee PKW/0/-/10, Packaging - Plastics.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a

3、 contract. Users are responsible for its correctapplication. The British Standards Institution 2012ISBN 978 0 580 69991 7ICS 55.100Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strate

4、gy Committee on 31 January 2012.Amendments issued since publicationDate Text affectedBS EN 16063:2011EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16063 November 2011 ICS 55.100 English Version Packaging - Rigid plastic containers - Nomenclature of plastic finishes Emballage - Rcipients en pl

5、astique rigide - Nomenclature des bagues en plastique Verpackung - Kunststoffbehltnisse - Bezeichnung von Kunststoffverschlussmundstcken This European Standard was approved by CEN on 29 October 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the condit

6、ions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists

7、in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standa

8、rds bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and Un

9、ited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16063:2011

10、: EBS EN 16063:2011EN 16063:2011 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Terms and definitions .53 Requirements .5Bibliography 7BS EN 16063:2011EN 16063:2011 (E) 3 Foreword This document (EN 16063:2011) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat

11、of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2012, and conflicting national standards shall be withdrawn at the latest by May 2012. Attention is drawn to the poss

12、ibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries a

13、re bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, S

14、pain, Sweden, Switzerland and the United Kingdom. BS EN 16063:2011EN 16063:2011 (E) 4 Introduction This European Standard is based on the ISBT (International Society of Beverage Technologists) Thread Nomenclature Card 1. Efficient packaging is of great importance for the distribution and the protect

15、ion of goods. Insufficient or inappropriate packaging can lead to damage or wastage of the contents of the pack. BS EN 16063:2011EN 16063:2011 (E) 5 1 Scope This European Standard specifies the dimension nomenclature for plastic finishes. 2 Terms and definitions For the purposes of this document, th

16、e following terms and definitions apply. 2.1 lead axial distance between two consecutive points of intersection of a helix by a line parallel to the axis of the cylinder on which it lies NOTE The axial movement of a thread part rotated one turn. 2.2 pitch distance measured parallel with its axis bet

17、ween corresponding points on adjacent thread forms in the same axial plane and on the same side of the axis NOTE Equals the lead divided by the number of thread starts. 3 Requirements Figure 1 gives the points which can be measured on thread finishes. All defined points are not necessarily required

18、or measured. BS EN 16063:2011EN 16063:2011 (E) 6 NOTE Reference dimensions are shown in parentheses. Key A Tamper evident bead diameter B Tamper evident band recess diameter Helix angle at pitch diameter pitch = 1/2 ( T + E) (not shown) C Control diameter at TOF D Tamper evident bead height measured

19、 from TOF to Gauge PT E Thread root diameter F Upper ring diameter G Lower ring diameter H Clearance height required for proper closure function I Minimum diameter thru finish J Height from TOF to the TOP of tamper evident bead K Height from TOF to the gauge point at start of full thread (at thread

20、start position) L Height from TOF to TOP of bead M Construction gauge PT on support ledge P Thread pitch (measured from K) PL Parting line PLK Height from TOF to the gauge point of first full thread taken at parting line (clockwise from thread start position) S Height from TOF to start of full depth

21、 of thread T Thread crest diameterTOF Top of finishV Control diameter depth W Width of bead X Height from TOF to bottom of support ledge Y Seal control length Z Maximum diameter on support ledge Gauge PT A point which may be required for construction or inspection of geometry INT PT Intersection poi

22、nt TAN PT Tangency point Construction Dimension provided for creation of geometry and not for general inspection (1) Gauge PT(2) Gauge PT at A or T preferred (3) P at Gauge PTFigure 1 Points which can be measured on thread finishes BS EN 16063:2011EN 16063:2011 (E) 7 Bibliography 1 Thread Nomenclatu

23、re Card ISBT (International Society of Beverage Technologists) 14070 Proton Rd. Suite 100, LB 9 Dallas TX 75244-3601 USA http:/www.bevtech.org This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other

24、standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BS

25、I)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the c

26、onstant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Simi

27、lary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996

28、 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20

29、 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanan

30、d international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact

31、Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and

32、documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical pu

33、blication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not pre

34、clude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: