EN 764-4-2014 en Pressure equipment - Part 4 Establishment of technical delivery conditions for metallic materials《压力设备 第4部分 金属材料技术交货条件的建立》.pdf

《EN 764-4-2014 en Pressure equipment - Part 4 Establishment of technical delivery conditions for metallic materials《压力设备 第4部分 金属材料技术交货条件的建立》.pdf》由会员分享，可在线阅读，更多相关《EN 764-4-2014 en Pressure equipment - Part 4 Establishment of technical delivery conditions for metallic materials《压力设备 第4部分 金属材料技术交货条件的建立》.pdf（46页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 764-4:2014Pressure equipmentPart 4: Establishment of technical deliveryconditions for metallic materialsBS EN 764-4:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 764-4:2014. Itsupersedes BS EN 764-4:2002 which is withdrawn.T

2、he UK participation in its preparation was entrusted to TechnicalCommittee PVE/1, Pressure Vessels.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are respon

3、sible for its correctapplication. The British Standards Institution 2015. Published by BSI StandardsLimited 2015ISBN 978 0 580 78027 1ICS 23.020.30Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards P

4、olicy and Strategy Committee on 31 January 2015.Amendments issued since publicationDate Text affectedBS EN 764-4:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 764-4 December 2014 ICS 23.020.30 Supersedes EN 764-4:2002English Version Pressure equipment - Part 4: Establishment of technical

5、delivery conditions for metallic materials Equipements sous pression - Partie 4: Etablissement des conditions techniques de livraison des matriaux mtalliques Druckgerte - Teil 4: Erstellung von technischen Lieferbedingungen fr metallische Werkstoffe This European Standard was approved by CEN on 8 No

6、vember 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be

7、obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to th

8、e CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ire

9、land, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Ce

10、ntre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 764-4:2014 EBS EN 764-4:2014EN 764-4:2014 (E) 2 Contents Page Foreword 4 1 Scope 5 2 Normative references 5 3 Terms and definitions, symbo

11、ls and abbreviations . 6 3.1 Terms and definitions . 6 3.2 Symbols and abbreviations 6 4 Types of technical delivery conditions . 8 4.1 Harmonized European Standards for material for pressure equipment 8 4.2 European Approvals for Materials for pressure equipment (EAMs) 8 4.3 Particular Material App

12、raisals for pressure equipment (PMAs) . 8 5 Content of technical delivery conditions for materials for pressure equipment 9 5.1 General 9 5.2 Requirements . 9 5.3 Testing and inspection 11 5.4 Marking . 12 Annex A (normative) Procedures for the establishment of European Approvals for pressure equipm

13、ent Materials (EAM) . 13 A.1 General 13 A.2 European Approvals for Materials . 13 A.3 Requirements for the establishment of an EAM . 13 A.4 Title scheme and structure of an EAM 14 Annex B (normative) Appraisal schedule for ferritic and martensitic steels 16 B.1 General 16 B.2 Test procedures . 16 B.

14、3 Required testing. 17 B.4 Subsequent testing 21 B.5 Collective tests . 22 Annex C (normative) Appraisal schedule for austenitic and austenitic-ferritic steels . 24 C.1 General 24 C.2 Test procedures . 24 C.3 Basic testing . 25 C.4 Sampling . 27 C.5 Extent of testing . 27 Annex D (normative) Apprais

15、al schedule for cast steels. 28 D.1 General 28 D.2 Test procedures . 28 D.3 Basic testing . 29 D.4 Sampling . 31 D.5 Extent of testing . 31 Annex E (normative) Test programme for welded specimen after stress relief procedure 33 E.1 Test programme . 33 E.2 Position of specimen . 33 Annex F (informati

16、ve) Example for Particular Material Appraisal (PMA) for steel . 35 Annex G (informative) History of EN 764-4 . 38 BS EN 764-4:2014EN 764-4:2014 (E) 3 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 97/23/EC on Pressure Equipment . 39

17、Bibliography 40 BS EN 764-4:2014EN 764-4:2014 (E) 4 Foreword This document (EN 764-4:2014) has been prepared by Technical Committee CEN/TC 54 “Unfired pressure vessels”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by public

18、ation of an identical text or by endorsement, at the latest by June 2015 and conflicting national standards shall be withdrawn at the latest by June 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall no

19、t be held responsible for identifying any or all such patent rights. This document supersedes EN 764-4:2002. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive. For relat

20、ionship with EU Directive 97/23/EC (PED), see informative Annex ZA, which is an integral part of this document. Regarding the most significant technical changes that have been implemented in this new edition of EN 764-4, see Annex G. EN 764, Pressure equipment, consists of the following parts: Part

21、1: Terminology - Pressure, temperature, volume, nominal size; Part 2: Quantities, symbols and units; Part 3: Definition of parties involved; Part 4: Establishment of technical delivery conditions for metallic materials (the present document); Part 5: Inspection documentation of metallic materials an

22、d compliance with the material specification; Part 6: Structure and content of operating instructions Technical Report CEN/TR 764-6; Part 7: Safety systems for unfired pressure equipment; Part 8: Proof test Technical Specification prCEN/TS 764-8, currently under development. According to the CEN-CEN

23、ELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, I

24、celand, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 764-4:2014EN 764-4:2014 (E) 5 1 Scope This European Standard specifies the requirements, under the regime

25、 of the EU Directive 97/23/EC on Pressure Equipment (PED), for the establishment of the technical delivery conditions in the form of: harmonized European Standards for material; European Approval for Materials (EAM); Particular Material Appraisal (PMA) for metallic materials for pressure equipment i

26、n all product forms. Welding consumables are not covered by this standard. This European Standard was developed predominantly on the basis of steel, nickel and nickel-based materials. However, application to other materials is not restricted but should consider specific aspects relevant to the mater

27、ial concerned. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (incl

28、uding any amendments) applies. EN 764-1:2004, Pressure equipment - Part 1: Terminology - Pressure, temperature, volume, nominal size EN 764-2:2012, Pressure equipment - Part 2: Quantities, symbols and units EN 10028 (all parts), Flat products made of steels for pressure purposes EN 10164, Steel prod

29、ucts with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions EN 10204, Metallic products - Types of inspection documents EN 10213, Steel castings for pressure purposes EN 10216 (all parts), Seamless steel tubes for pressure purposes - Technica

30、l delivery conditions EN 10217 (all parts), Welded steel tubes for pressure purposes - Technical delivery conditions EN 10222 (all parts), Steel forgings for pressure purposes EN 10272, Stainless steel bars for pressure purposes EN 10273, Hot rolled weldable steel bars for pressure purposes with spe

31、cified elevated temperature properties EN 10314, Method for the derivation of minimum values of proof strength of steel at elevated temperatures EN ISO 148-1, Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1) EN ISO 204, Metallic materials - Uniaxial creep testing in

32、 tension - Method of test (ISO 204) EN ISO 6892-1:2009, Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1) BS EN 764-4:2014EN 764-4:2014 (E) 6 EN ISO 10052, Acoustics - Field measurements of airborne and impact sound insulation and of service equipment sou

33、nd - Survey method (ISO 10052) EN ISO 15607, Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607) CR ISO 15608:2000, Welding - Guidelines for a metallic material grouping system (ISO/TR 15608:2000) EN ISO 15614-1, Specification and qualification of

34、 welding procedures for metallic materials - Welding procedure test - Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys (ISO 15614-1) 3 Terms and definitions, symbols and abbreviations 3.1 Terms and definitions For the purposes of this document, the following terms an

35、d definitions apply. 3.1.1 European Approval for Materials EAM technical document defining the characteristics of materials intended for repeated use in the manufacture of pressure equipment which are not covered by any harmonized standard Note 1 to entry: See Article 11 of the EU Directive 97/23/EC

36、 on Pressure Equipment (PED) and see also the PED Guideline 7/26. 3.2 Symbols and abbreviations For the purposes of this standard, the symbols and abbreviations of EN 764-1:2004, EN 764-2:2012 and the following in Table 1 and Table 2 apply. BS EN 764-4:2014EN 764-4:2014 (E) 7 Table 1 Symbols and uni

37、ts Symbols Characteristic Units b width mm e thickness mm h max. permissible reinforcement of weld mm T temperature C TDdesign temperature C A elongation after fracture % C constant D diameter mm E modulus of elasticity MPa G shear modulus MPa HV Vickers hardness KV2Charpy V-notch impact energy J Lo

38、original gauge length mm P pressure bar PLMparameter according to Larson-Miller Reyield strength MPa ReHupper yield strength MPa ReLlower yield strength MPa Rmtensile strength MPa Rcm/t/Tcreep rupture strength for t hours at T C MPa Rm/Ttensile strength at temperature T MPa Rp0,2/T0,2 % proof streng

39、th at temperature T MPa Rp0,20,2 % proof strength MPa Rp1,01,0 % proof strength MPa Rp1,0/T1,0 % proof strength at temperature T MPa Sooriginal cross sectional area mm2t time h linear expansion coefficient K 1 strain % V Poissons ratio BS EN 764-4:2014EN 764-4:2014 (E) 8 Table 2 Abbreviations Abbrev

40、iation Description EAM European Approval for Materials EC European Commission PED Pressure Equipment Directive PMA Particular Material Appraisal OJEU Official Journal of the European Union 4 Types of technical delivery conditions 4.1 Harmonized European Standards for material for pressure equipment

41、Harmonized European material standards under the regime of the PED define the technical requirements for materials frequently used in pressure equipment in Europe. It is within the remit of the responsible technical committee for materials to check at each occasion of the revision work whether relat

42、ed material grades covered by an EAM are used to an extent that justifies the incorporation of the grade into the relevant harmonized European material Standard. 4.2 European Approvals for Materials for pressure equipment (EAMs) A European approval for materials means a technical document defining t

43、he characteristics of materials intended for repeated use in the manufacture of pressure equipment, the type of which is not covered by any harmonized European material standard. According to Guiding Principles for the contents of EAM drafts, agreed by the Member States of the European Union and the

44、 European Commission, it shall i.a. describe material properties in a concise, complete and correct manner. The ways and means undertaken to achieve an EAM and a data sheet containing at least the applicable elements is given in Annex A. An EAM shall not be issued for: a) a grade of material listed

45、in a current or former national material standard that has a specification covered by a harmonized European material standard; b) a grade of material which is previously included in a European national material standard but which is not included in the harmonized European material standard which has

46、 replaced the European national material standard (ref. PED Guideline 7/26). NOTE 1 Reference of available EAMs is published in the Official Journal of the European Union (OJEU). NOTE 2 Actual EAMs are also published at the following website of the European Commission: http:/ec.europa.eu/enterprise/

47、sectors/pressure-and-gas/documents/ped/materials/index_en.htm. 4.3 Particular Material Appraisals for pressure equipment (PMAs) Particular material appraisals apply for individual cases as for example: a) a material grade or a product form or a thickness not covered by a harmonized European material

48、 standard, harmonized under the scope of the PED, or by an EAM; BS EN 764-4:2014EN 764-4:2014 (E) 9 b) a product specified in a harmonized European material standard for pressure purposes or in an EAM is intended in an exceptional case for service conditions outside its specified range of applicatio

49、n. For pressure equipment classified in category III and IV according to the PED, the PMA/PMAs, which irrespective of category (I to IV) always shall be drawn up by the equipment manufacturer, shall be appraised and confirmed by the Notified Body in charge of the conformity assessment for the actual piece of pressure equipment. Where relevant to the pressure equipment under consideration the requirements given in Annex B to Annex E together with EN 13445-2:2014, 4.1 and 4.2, may be used as guidance. An example for PMA is given in