EN 3763-2010 en Aerospace series - Nuts hexagonal self-locking ball seat in heat resisting steel MoS2 lubricated - Classification 900 MPa (at ambient temperature) 315 Degrees C《航空.pdf

《EN 3763-2010 en Aerospace series - Nuts hexagonal self-locking ball seat in heat resisting steel MoS2 lubricated - Classification 900 MPa (at ambient temperature) 315 Degrees C《航空.pdf》由会员分享，可在线阅读，更多相关《EN 3763-2010 en Aerospace series - Nuts hexagonal self-locking ball seat in heat resisting steel MoS2 lubricated - Classification 900 MPa (at ambient temperature) 315 Degrees C《航空.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 3763:2010ICS 49.030.30NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAerospace series Nuts, hexagonal, self-locking, ball seat, in heat resisting steel, MoS2lubricated Classification: 900 MPa (at ambient temperature) / 315 CThis British Standardwas publis

2、hed under theauthority of the StandardsPolicy and StrategyCommittee on 28 February2010 BSI 2010ISBN 978 0 580 70527 4Amendments/corrigenda issued since publicationDate CommentsBS EN 3763:2010National forewordThis British Standard is the UK implementation of EN 3763:2010.The UK participation in its p

3、reparation was entrusted to TechnicalCommittee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsi

4、ble for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS EN 3763:2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3763 January 2010 ICS 49.030.30 English Version Aerospace series - Nuts, hexagonal, self-locking, ball seat, in heat res

5、isting steel, MoS2lubricated - Classification: 900 MPa (at ambient temperature) / 315 C Srie arospatiale - crous hexagonaux, freinage interne, orientables, en acier rsistant chaud, lubrifis MoS2- Classification: 900 MPa ( temprature ambiante) / 315 CLuft- und Raumfahrt - Sechskantmuttern, selbstsich

6、ernd, fr Neigungsausgleich, aus hochwarmfestem Stahl, MoS2-geschmiert - Klasse: 900 MPa (bei Raumtemperatur) / 315 C This European Standard was approved by CEN on 4 December 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

7、 European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (

8、English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulg

9、aria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR

10、 STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3763:2010: EBS EN 3763:2010EN 3763:2010 (E) 2

11、Contents Page Foreword 31 Scope 42 Normative references 43 Required characteristics .54 Designation 75 Marking .76 Technical specification .7Annex A (informative) Assembly .8BS EN 3763:2010EN 3763:2010 (E) 3 Foreword This document (EN 3763:2010) has been prepared by the Aerospace and Defence Industr

12、ies Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to

13、CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2010, and conflicting national standards shall be withdrawn at the latest by July 2010. Attention is drawn to the possibility that some of

14、 the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implemen

15、t this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switze

16、rland and the United Kingdom. BS EN 3763:2010EN 3763:2010 (E) 4 1 Scope This standard specifies the characteristics of self-locking hexagonal nuts with ball seat in heat resisting steel, MoS2lubricated. Classification: 900 MPa1) / 315 C2).They are intended to be used with washers to EN 3764 or suita

17、ble parts, see Annex A. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN

18、 2424, Aerospace series Marking of aerospace products EN 2491, Aerospace series Molybdenum disulphide dry lubricants Coating methods EN 3764, Aerospace series Washers, concave, in heat resisting steel, passivated3)EN 9100, Quality Management Systems Requirements for Aviation, Space and Defense Organ

19、izations EN 9133, Aerospace series Quality management systems Qualification procedure for aerospace standard parts TR 3791, Aerospace series Materials for self-locking nuts, threaded inserts and screw thread inserts of temperature classes 425 C4)ISO 5855-2, Aerospace MJ threads Part 2: Limit dimensi

20、ons for bolts and nuts ISO 5858, Aerospace Nuts, self-locking, with maximum operating temperature less than or equal to 425 C Procurement specification ISO 8788, Aerospace Nuts, metric Tolerances of form and position 1) Corresponds to the minimum tensile stress which the nut is able to withstand at

21、ambient temperature without breaking or cracking when tested with a bolt of a higher strength class. 2) Maximum temperature that the nut is able to withstand, without permanent alteration to its original characteristics, after ambient temperature has been restored. The maximum temperature is conditi

22、oned by the surface treatment. 3) Published as ASD-STAN Prestandard at the date of publication of this standard. 4) Published as ASD-STAN Technical Report at the date of publication of this standard. BS EN 3763:2010EN 3763:2010 (E) 5 3 Required characteristics 3.1 Configuration Dimensions Masses See

23、 Figure 1 and Table 1. Dimensions and tolerances are expressed in millimetres and apply before MoS2lubrication. Details of form not stated are at the manufacturers option. 3.2 Tolerances of form and position ISO 8788. 3.3 Materials TR 3791. 3.4 Surface treatment EN 2491, thickness not specified. BS

24、EN 3763:2010EN 3763:2010 (E) 6 These values in micrometres apply before surface treatment. They do not apply tothreads the surface texture of which will be as achieved by usual manufacturingmethods. Remove sharp edges 0,1 to 0,4. Key 1 Marking (optional location, at the manufacturers discretion) 2 F

25、orm out-of-round in this area to achieve the self-locking torque requirement. Tooling marks are permitted in this area. 3 Spherical 4 Thread 5 Chamfer, radius or broken edge Figure 1 Table 1 Diameter code Thread a Eb FbG H J M N P RT Massc min. 0,2 max. min. min. min. min.0 0,5050 MJ50,8-4H6H 6,5 6

26、h1210,3 7,05 5,5 1,7 2 2,05 8 7,5 1,7 060 MJ61-4H5H 7,6 7 13 8,1 6,5 2,5 2,3 2,7 9 8,4 2,5 080 MJ81-4H5H 10,9 10 h1317 9,7 8,5 3 3,2 2,5 12,5 11,75 6,5 100 MJ101,25-4H5H 13,2 12 21 11,95 10,5 4 3,3 2,95 16 15,1 11,3 120 MJ121,25-4H5H 15,5 14 24 13,46 12,5 4,5 4,5 2,65 18 16,9 17,4 aIn accordance wit

27、h ISO 5855-2. In the self-locking zone, the tolerances apply before forming out-of-round. bThese dimensions apply before forming out-of-round, but finished nuts shall fit a standard socket wrench. cApproximate values (kg/1 000 pieces), given for information purposes only. 6,3 1,6 BS EN 3763:2010EN 3

28、763:2010 (E) 7 4 Designation EXAMPLE Description block NUT Identity block EN3763060 Number of this standard Diameter code (see Table 1) NOTE If necessary the originator code I9005 shall be placed between the description block and the identity block. 5 Marking EN 2424, style N plus diameter code. See

29、 Figure 1. 6 Technical specification ISO 5858, except for: Approval of manufacturers: see EN 9100; Qualification of products, nut and washer (EN 3764): see EN 9133. BS EN 3763:2010EN 3763:2010 (E) 8 Annex A (informative) Assembly A.1 Dimensions See Figure A.1 and Table A.1. Figure A.1 Table A.1 Diam

30、eter code V max. W min. 050 8,25 3,05 060 9,1 3,5 080 11,4 4 100 13,95 4,75 120 16,25 5,25 BS EN 3763:2010EN 3763:2010 (E) 9 A.2 Examples See Figures A.2 and A.3. Figure A.2 Figure A.3 BS EN3763:2010BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 89

31、96 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users

32、 of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of

33、the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buyin

34、g standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for interna

35、tional standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical

36、 Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developments

37、and receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at

38、 http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 n

39、o extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: