EN 2241-2010 en Aerospace series - Lamp caps - Dimensions《航空航天系列 灯头 尺寸》.pdf

《EN 2241-2010 en Aerospace series - Lamp caps - Dimensions《航空航天系列 灯头 尺寸》.pdf》由会员分享，可在线阅读，更多相关《EN 2241-2010 en Aerospace series - Lamp caps - Dimensions《航空航天系列 灯头 尺寸》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 2241:2010ICS 49.060NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAerospace series Lamp caps DimensionsThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 30 April2010. BSI 2010ISBN 978 0 580 69796 8Amendm

2、ents/corrigenda issued since publicationDate CommentsBS EN 2241:2010National forewordThis British Standard is the UK implementation of EN 2241:2010.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/6, Aerospace avionic electrical and fibre optictechnology.A list of orga

3、nizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations

4、.BS EN 2241:2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2241 March 2010 ICS 49.060 English Version Aerospace series - Lamp caps - Dimensions Srie arospatiale - Culots de lampes - Dimensions Luft- und Raumfahrt - Lampensockel - Mae This European Standard was approved by CEN on 27 Februar

5、y 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtai

6、ned on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Managem

7、ent Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlan

8、ds, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in a

9、ny form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2241:2010: EBS EN 2241:2010EN 2241:2010 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Caps dimensions .44.1 General 44.2 Dimensions of bi-pin cap 54.3 Dimensions of SX4s/4 c

10、ap 64.4 Dimensions of SY4s/7 cap 74.5 Dimensions of SX6s cap .84.6 Dimensions of S5,7s/8 .94.7 Dimensions of BA7s/12 cap . 104.8 Dimensions of BA9s/13 cap . 114.9 Dimensions of BA15s/19 cap . 124.10 Dimensions of BA15s/19 cap . 134.11 Dimensions of BA15d/19 cap 144.12 Dimensions of BAY15s/19 cap 154

11、.13 Dimensions of BA15s3/19 cap . 164.14 Dimensions of BA20d cap . 175 Quality assurance . 186 Technical specification 18BS EN 2241:2010EN 2241:2010 (E) 3 Foreword This document (EN 2241:2010) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN

12、). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status

13、 of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2010, and conflicting national standards shall be withdrawn at the latest by September 2010. Attention is drawn to the possibility that some of the elements of this document may be the s

14、ubject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium,

15、 Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 2241:20

16、10EN 2241:2010 (E) 4 1 Scope This standard specifies the dimensions of caps for incandescent lamps used on board aircraft respectively the characteristics and tests of which are defined in EN 2240-001 and EN 2756. 2 Normative references The following referenced documents are indispensable for the ap

17、plication of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2241-001, Aerospace series Incandescent lamps Part 001: Technical specification EN 2756, Aerospace series Lam

18、ps, incandescent Test methods EN 9133, Aerospace series Quality management systems Qualification procedure for aerospace standard parts EN 60061-1:1993, Lamp caps and holders together with gauges for the control of interchangeability and safety Part 1: Lamps caps (IEC 60061-1:1969 + supplements A:19

19、70 to N:1992, modified) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 cap part of a lamp which holds it in a lampholder and provides connection to the electric supply 4 Caps dimensions 4.1 General See 4.2 to 4.14. Dimensions and tolerances

20、are in millimetres. BS EN 2241:2010EN 2241:2010 (E) 5 4.2 Dimensions of bi-pin cap See Figure 1 and Table 1. Key 1 Level of dimension B. Dimension B is specified flush with the base. Figure 1 Table 1 Dimensions in millimetres Dimensions Bi-Pin reference G 3,17 G 2,54 GX 2,54 G 1,27 GX 1,27 Type T1 3

21、/4 T1 1/4 T1 T1 T1 A min. 5,70 4,60 3,70 3,70 3,20 max. 5,90 4,80 3,90 3,90 3,40 B min. 3,07 2,44 2,44 1,17 1,17 max. 3,27 2,64 2,64 1,37 1,37 C min. 5,85 5,85 5,85 5,85 5,85 max. 6,85 6,85 6,85 6,85 6,85 D min. 0,45 0,45 0,45 0,45 0,45 max. 0,55 0,55 0,55 0,55 0,55 E min. 8,50 7,20 5,20 5,20 3,00 m

22、ax. 9,00 7,70 5,70 5,70 3,40 The location of the pins, their relative position and their position relative to the cap barrel shall be checked by means of a gauge (under study). BS EN 2241:2010EN 2241:2010 (E) 6 4.3 Dimensions of SX4s/4 cap See Figure 2 and Table 2. Key 1 Bulbed edge or chamfer Figur

23、e 2 Table 2 Dimensions in millimetres Dimensions min. max. A 3,89 4,04 B 4,47 4,72 C 0,43 0,58 D 1,35 D11,65 2,16 E 2,57 2,72 G 3,71 3,91 H To be defined K 0,33 0,43 S 0,30 BS EN 2241:2010EN 2241:2010 (E) 7 4.4 Dimensions of SY4s/7 cap See Figure 3 and Table 3. Key 1 Bulbed edge or chamfer Figure 3

24、Table 3 Dimensions in millimetres Dimensions min. max. A 3,90 3,95 B 4,50 4,60 C 1,00 D 1,90 D12,25 2,75 E 4,80 5,20 G 3,40 3,60 H 1,80 2,20 S 0,30 BS EN 2241:2010EN 2241:2010 (E) 8 4.5 Dimensions of SX6s cap See Figure 4 and Table 4. Key 1 Bulbed edge or chamfer Figure 4 Table 4 Dimensions in milli

25、metres Dimensions min. max. A 6,10 6,35 B 7,11 7,37 D11,70 2,80 E 6,35 6,85 G 6,22 6,98 H 2,54 3,30 R2 0,20 S 0,38 BS EN 2241:2010EN 2241:2010 (E) 9 4.6 Dimensions of S5,7s/8 In conformity with EN 60061-1:1993 sheet 7004-62-1 See Figure 5 and Table 5. Key 1 Solder on finished lamp 2 Datum line: Bott

26、om of groove Figure 5 Table 5 Dimensions in millimetres Dimensions min. max. Dimensions min. max. A 5,56 5,82 Ma8,10 8,65 B 5,51 5,72 ra0,38 0,51 C 0,80 S 0,40 D a 1,70 2,70 X 0,76 D12,40 3,30 Y 2,30 H 3,20 aMeasured on non-assembled base. BS EN 2241:2010EN 2241:2010 (E) 10 4.7 Dimensions of BA7s/12

27、 cap See Figure 6 and Table 6. Figure 6 Table 6 Dimensions in millimetres Dimensions min. max. Dimensions min. max. A a 6,87 7,05 F 0,70 0,90 C 0,90 b G 3,40 4,00 D 7,70 b8,10bH 2,40 2,60 D1 8,70 N a2,60 E 1,80 2,00 Approx. 30 aDimension N gives the minimum length along which dimension A must be in

28、compliance. bMeasured on non-assembled base. BS EN 2241:2010EN 2241:2010 (E) 11 4.8 Dimensions of BA9s/13 cap In conformity with EN 60061-1:1993 sheet 7004-14-7. See Figure 7 and Table 7. Figure 7 Table 7 Dimensions in millimetres Dimensions min. max. Dimensions min. max. A a 9,08 9,25 F 0,64 B 9,75

29、10,16 H 3,50 4,00 C 1,50 b M 12,90 13,30 D4,30 b5,20 bN a4,50 D1 5,90 P 11,00 E 1,50 1,70 aDimension N gives the minimum length along which dimension A must be in compliance. bMeasured on non-assembled base. BS EN 2241:2010EN 2241:2010 (E) 12 4.9 Dimensions of BA15s/19 cap In conformity with EN 6006

30、1-1:1993 sheet 7004-14-7. See Figure 8 and Table 8. Figure 8 Table 8 Dimensions in millimetres Dimensions min. max. Dimensions min. max. A a 9,08 9,25 F 0,64 B 9,7510,16 H 3,50 4,00 C 1,50 b M 13,75 14,25 D4,30 b5,20 bN a4,50 D1 5,90 P 11,00 E 1,50 1,70 aDimension N gives the minimum length along wh

31、ich dimension A must be in compliance. bMeasured on non-assembled base. BS EN 2241:2010EN 2241:2010 (E) 13 4.10 Dimensions of BA15s/19 cap In conformity with EN 60061-1:1993 sheet 7004-11A-7. See Figure 9 and Table 9. Figure 9 Table 9 Dimensions in millimetres Dimensions min. max. Dimensions min. ma

32、x. A a 15,05 15,30 F 0,64 B 15,6516,15 H 4,50 b5,20 bC 1,50 b M 18,75 19,25 D6,00 b6,60 bNa 8,90 D16,32 7,50 P 17,00 E 1,80 2,20 aDimension N gives the minimum length along which dimension A must be in compliance. bMeasured on non-assembled base. BS EN 2241:2010EN 2241:2010 (E) 14 4.11 Dimensions of

33、 BA15d/19 cap In conformity with EN 60061-1:1993 sheet 7004-11A-7. See Figure 10 and Table 10. Figure 10 Table 10 Dimensions in millimetres Dimensions min. max. Dimensions min. max. A a 15,05 15,30 G About 9bB 15,6516,15 J 3,00 C 1,50 b K 7,00 8,00 D6,00 b6,60 bM 18,75 19,25 D16,32 7,50 N a 8,90 E 1

34、,80 2,20 P 17,00 F 0,64 aDimension N gives the minimum length along which dimension A must be in compliance. bMeasured on non-assembled base. BS EN 2241:2010EN 2241:2010 (E) 15 4.12 Dimensions of BAY15s/19 cap See Figure 11 and Table 11. Figure 11 Table 11 Dimensions in millimetres Dimensions min. m

35、ax. Dimensions min. max. A a 15,05 15,30 F 0,64 B 15,6516,15 H 4,50 b5,20 bC 1,50 b L 3,00 3,40 D6,00 b6,50 bM 18,75 19,25 D16,52 7,50 N a 8,90 E 1,80 2,20 P 17,00 aDimension N gives the minimum length along which dimension A must be in compliance. bMeasured on non-assembled base. BS EN 2241:2010EN

36、2241:2010 (E) 16 4.13 Dimensions of BA15s3/19 cap See Figure 12 and Table 12. Figure 12 Table 12 Dimensions in millimetres Dimensions min. max. Dimensions min. max. A a 15,05 15,30 E 1,80 2,20 B 15,6516,15 F 0,64 C 1,50 b H 4,50 5,20 D6,00 b6,60 bM 18,75 19,25 D16,32 7,50 N a 8,90 aDimension N gives

37、 the minimum length along which dimension A must be in compliance. bMeasured on non-assembled base. BS EN 2241:2010EN 2241:2010 (E) 17 4.14 Dimensions of BA20d cap In conformity with EN 60061-1:1993 sheet 7004-12-6. See Figure 13 and Table 13. Figure 13 Table 13 Dimensions in millimetres Dimensions

38、min. max. Dimensions min. max. A a 19,95 20,10 J 3,00 C 1,50 K 9,50 b10,00 cD b 15,50 16,00 cL 0,40 D1 17,00 Na 5,00 E14,40 4,50 r 0,20 E22,90 3,00 82 30 97 30 F 1,90 2,20 M To be defined G About 12 b aDimension N gives the minimum length along which dimension A must be in compliance. bMaximum devia

39、tion in height between lugs 0,15 mm. cMeasured on non-assembled base. BS EN 2241:2010EN 2241:2010 (E) 18 5 Quality assurance See EN 9133. 6 Technical specification See EN 2240-001. BS EN 2241:2010This page has been intentionally left blankBS EN2241:2010BSI GroupHeadquarters 389Chiswick High Road,Lon

40、don, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish

41、 Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usi

42、ngthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automa

43、tically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Sho

44、p on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinterna

45、tional standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members

46、of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British

47、 Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitt

48、ed under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Det