EN 1093-8-1998 en Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 8 Pollutant concentration parameter test bench method (Incorporates Amend.pdf

《EN 1093-8-1998 en Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 8 Pollutant concentration parameter test bench method (Incorporates Amend.pdf》由会员分享，可在线阅读，更多相关《EN 1093-8-1998 en Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 8 Pollutant concentration parameter test bench method (Incorporates Amend.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 1093-8:1998 +A1:2008Safety of machinery Evaluation of the emission of airborne hazardous substances Part 8: Pollutant concentration parameter, test bench methodICS 13.040.40; 23.120g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3

2、g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 1093-8:1998+A1:2008This British Standard waspublished under the authority of the Standards Committee and comes into effect on 15 January 1999 BSI 2008ISBN 978 0 580 61262 6National forewordTh

3、is British Standard is the UK implementation of EN 1093-8:1998+A1:2008. It supersedes BS EN 1093-8:1998 which is withdrawn.The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to CEN text carry the number of the CEN amendment. For

4、example, text altered by CEN amendment A1 is indicated by !“.The UK participation in its preparation was entrusted to Technical Committee MCE/3, Safeguarding of machinery.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purpo

5、rt to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate Comments30 November 2008 Implementation of CEN amendment A1:

6、2008 andalignment of BSI and CEN publications datesEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1093-8:1998+A1 July 2008 ICS 13.040.40 Supersedes EN 1093-8:1998English Version Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 8: Pollutant concentration

7、parameter, test bench method Scurit des machines - Evaluation de lmission de substances dangereuses vhicules par lair - Partie 8: Paramtre de concentration en polluant, mthode sur banc dessai Sicherheit von Maschinen - Bewertung der Emission von luftgetragenen Gefahrstoffen - Teil 8: Konzentrationsp

8、arameter des luftverunreinigenden Stoffes, Prfstandverfahren This European Standard was approved by CEN on 4 September 1998 and includes Amendment 1 approved by CEN on 8 June 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving thi

9、s European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions

10、(English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bul

11、garia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDAR

12、DIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1093-8:1998+A1:2008: EEN 1093-8:1998+A1:2008 (E) 2 C

13、ontents Page Foreword3 Introduction .4 1 Scope 4 2 Normative references 4 3 Definitions 5 4 Principle5 5 Test bench6 5.1 Description of the test bench .6 5.2 Location of measurement points .7 6 Procedure .7 6.1 Operation of the machines .7 6.2 Measurement procedures .7 7 Expression of results 7 8 Te

14、st report 8 Annex ZA (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC“.9 Annex ZB (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC“.10 Bibliography 11 BS EN 1093-8:19

15、98+A1:2008EN 1093-8:1998+A1:2008 (E) 3 Foreword This document (EN 1093-8:1998+A1:2008) has been prepared by Technical Committee CEN/TC 114 “Safety of machinery“, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of

16、 an identical text or by endorsement, at the latest by January 2009, and conflicting national standards shall be withdrawn at the latest by December 2009. This document includes Amendment 1, approved by CEN on 2008-06-08. This document supersedes EN 1093-8:1998. The start and finish of text introduc

17、ed or altered by amendment is indicated in the text by tags ! “. This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). !For relationship with EU Directive(s), s

18、ee informative Annexes ZA and ZB, which are integral parts of this document.“ According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark,

19、 Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. BS EN 1093-8:1998+A1:2008EN 1093-8:1998+A1:2008 (E) 4 Introduction Th

20、is European Standard is a type B standard as stated in ENV 1070:1993. This European Standard is a part of EN 1093. Part 1 of this standard presents a selection of different methods for the evaluation of the emission of airborne hazardous substances from machines. 1 Scope This European Standard speci

21、fies a test bench method for the measurement of the pollutant concentration parameter of a specified airborne hazardous substance from machines using a test bench under specified operating conditions. This method is only applicable for the determination of emitted gases, vapours and respirable parti

22、cles. The determination of the emission rate in a test bench (see EN 1093-3) shall be used when possible. Measurement of the pollutant concentration parameter of a machine can serve for the: a) evaluation of the performance of a machine; b) evaluation of the improvement of the machine; c) comparison

23、 of machines within groups of machines with the same intended use (groups are defined by the function and materials processed), d) ranking of machines from the same group according to their pollutant concentration parameters; e) determination of the state of the art of machines with respect to their

24、 pollutant concentration parameter. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references

25、, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 292-1:1991, Safety of machinery - Basic concepts, general p

26、rinciples for design - Part 1: Basic terminology, methodology. EN 292-2:1991, Safety of machinery - Basic concepts, general principles for design - Part 2: Technical principles and specifications. EN 292-2/A1:1995, Safety of machinery - Basic concepts, general principles for design - Part 2: Technic

27、al principles and specifications; Amendment A1. ENV 1070:1993, Safety of machinery Terminology. EN 1093-1, Safety of machinery - Evaluation of the emission of airborne hazardous substances Part 1: Selection of test methods. BS EN 1093-8:1998+A1:2008EN 1093-8:1998+A1:2008 (E) 5 ISO 2602:1980, Statist

28、ical interpretation of test results - Estimation of the mean - Confidence interval. 3 Definitions For the purposes of this European Standard the definitions of ENV 1070:1993 and the following definition applies: 3.1 pollutant concentration parameter, cabin, Pcc the measured concentration of a specif

29、ied pollutant in defined position(s) near the machine. For the purpose of this European Standard one measurement point shall be used, preferably in the duct. 4 Principle The principle of the measurement method is to operate machines under controlled conditions in a test bench and to measure the poll

30、utant concentration at a well defined location (see 5.2) for a specified exhaust air flow rate of the test bench. This concentration gives an indication of the emission from the machine. BS EN 1093-8:1998+A1:2008EN 1093-8:1998+A1:2008 (E) 6 5 Test bench 5.1 Description of the test bench The test ben

31、ch consists of a cabin with a funnel and a subsequent air mover (see figure 1). Ac cross section of the cabin; H height of the cabin; h height of the emission source from the cabin floor; W width of the cabin; 1 test cabin; 2 source1); 3 funnel; 4 measurement point 2; 5 tunnel; 6 preferred measureme

32、nt point 1; 7 air mover. W/H 0,66 1,5 h 0,66H l0 0,5Acl1 0,5Ac 2,0Ac 2,0m L2 0,5Ac Ac l3 5d l4 3d QE cabin exhaust flow rate Figure 1 Test bench (schematic layout) The air mover produces an air flow in the test cabin from the inlet towards the funnel. The cabin shall be equipped with a permeable inl

33、et (e. g. macroporous filter material, perforated plastic foil or plate) in order to obtain a uniform air flow across the inlet and to avoid the escape of the pollutant from the cabin. The cabin exhaust flow rate shall be specified in type C standards. It has to be controlled in order to remain cons

34、tant. The cross section of the cabin (form and dimensions) shall be chosen according to the size of the machine. The maximum cross section area of the machine shall not exceed a fifth of the cross section area of the cabin. 1) Generally the source cannot be considered as a point, but as a zone inclu

35、ding several sources. BS EN 1093-8:1998+A1:2008EN 1093-8:1998+A1:2008 (E) 7 The cabin shall be long enough to accommodate the machine and the operator with the emission sources as close to the specified location as practicable in figure 1. The machines shall be positioned in the cabin in such a way

36、that the source of the pollutant emitted from the machine is in the area of the longitudinal axis of the cabin at a distance of l1from the beginning of the funnel and of l0from the inlet. 5.2 Location of measurement points The concentration of the pollutant shall be measured at the measurement point

37、 1 in the exhaust duct. If it is necessary to use measuring instruments, which have bigger sampling heads and/or are only suitable for lower air velocities, the measurement point 2, located in the area of the middle axis of the funnel as near as possible to the duct may be used. 6 Procedure 6.1 Oper

38、ation of the machines The machine shall be operated according to its intended use. The stipulation of working procedures, the tools used and the materials to be processed with specified categories of machines will be defined in type C standards. If the machine is equipped with its own separator reci

39、rculating air towards the working zone according to the intended use, the outlet of the separator shall be located in the cabin in such a way as to ensure that the pollutant from this secondary source reaches the measurement point. The machine shall be operated in accordance with the manufacturers i

40、nstructions. When the machine is provided with pollution control equipment this shall be adjusted according to these instructions. Tests shall not be carried out unless manufacturers specifications for operating the pollution control equipment are available. 6.2 Measurement procedures The measuremen

41、t procedures used for the pollutant concentration shall comply with the appropriate International and European standards. Detailed procedures shall be specified in the appropriate type C standards for each type of machine. The measurement shall take into account the normal operational cycles of the

42、machine. The measurement time shall be sufficient to collect concentration data representative of the normal operational cycles of the machines. As least three tests shall be performed. 7 Expression of results The pollutant concentration parameter, cabin Pcc, is the mean value and the 95 % confidenc

43、e interval according to ISO 2602 of the test results. BS EN 1093-8:1998+A1:2008EN 1093-8:1998+A1:2008 (E) 8 8 Test report The test report shall include at least the following information: a) reference to this standard and appropriate type C standards; b) description of the machine tested (e.g. manuf

44、acturer, model, type, version, design, size, year of manufacture, serial number) for the machine itself and for each additional piece of equipment; c) operational data during tests, including tools used with the machine and the material processed on the machine; d) description of the pollution contr

45、ol equipment (e.g. manufacturer, model, type, version, design, size, year of manufacture, serial number, operational data); e) cabin exhaust flow rate; f) description of measurement procedures including the locations of the measurement point and pollutant measured; g) measuring instruments used and

46、their most recent calibration date; h) environmental data (temperature, humidity, atmospheric pressure); i) description of procedures used (e.g. list of standards) for concentration and flow rate measurements; j) number of tests performed; k) measured concentrations; l) pollutant concentration param

47、eter Pccmean value, 95 % confidence interval; m) comments on deviations from any relevant standards; n) test laboratory; o) name of the test person responsible; p) date of testing; q) additional comments, if necessary. BS EN 1093-8:1998+A1:2008EN 1093-8:1998+A1:2008 (E) 9 Annex ZA (informative) !Rel

48、ationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association to provide a means of conforming to Essential Requirements of the

49、New Approach Directive Machinery 98/37/EC, amended by Directive 98/79/EC. Once this standard is cited in the Official Journal of the European Communities under that Directive and has been implemented as a national standard in at least one Member State, compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of the scope of this standard, a presumption of conformity with the corresponding Essential Requirements of that Directive and associated EFTA regulations. Table ZA.1 Correspondence be