DLA SMD-5962-84111 REV F-2010 MICROCIRCUIT MEMORY DIGITAL 262 144-BIT (32K X 8) UV ERASEABLE PROM MONOLITHIC SILICON.pdf
《DLA SMD-5962-84111 REV F-2010 MICROCIRCUIT MEMORY DIGITAL 262 144-BIT (32K X 8) UV ERASEABLE PROM MONOLITHIC SILICON.pdf》由会员分享,可在线阅读,更多相关《DLA SMD-5962-84111 REV F-2010 MICROCIRCUIT MEMORY DIGITAL 262 144-BIT (32K X 8) UV ERASEABLE PROM MONOLITHIC SILICON.pdf(16页珍藏版)》请在麦多课文档分享上搜索。
1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED C Convert to military drawing format. Change drawing CAGE code to 67268. Add vendor CAGE 01295. Minor changes to table I and table II. Editorial changes throughout. Add device type 05 1987 OCT 13 M. A. Frye D Deleted CAGE 01295. Editorial changes t
2、hroughout. Made technical changes to table I, margin test method C (step 4), paragraph 4.3.1 (step C), table II, figure 5, paragraph 4.2, margin test method B (step 3), paragraph 1.2.2, paragraph 1.3, paragraph 1.4, figure 6, and table III. Added footnote 3, removed vendor name and address under ven
3、dor name and address, and added M38510/22403BYX to 8411104YX. 1989 JAN 11 M. A. Frye E Convert to newer standard boilerplate with the additional of QD requirement paragraphs. Changed maximum CIon table I from 6 pF to 10 pF and COfrom 12 pF to 15 pF. Changed subgroup 7 to 3 in Table II for Group C an
4、d D end-point electrical parameters. Updated boilerplate paragraphs. ksr 2004 NOV 08 Ray Monnin F Updated boilerplate paragraphs. glg 10-02-16 Charles Saffle The original first page of this drawing has been replaced. REV SHEET REV F SHEET 15 REV STATUS REV F F F F F F F F F F F F F F OF SHEETS SHEET
5、 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Steve Duncan DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Ray Monnin COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Michael A Frye MICROCIRCUIT, MEMORY
6、 DIGITAL, 262,144-BIT (32K X 8) UV ERASEABLE PROM, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 18 October 1984 AMSC N/A REVISION LEVEL F SIZE A CAGE CODE 67268 84111 SHEET 1 OF 15 DSCC FORM 2233 APR 97 5962-E052-10 Provided by IHSNot for ResaleNo reproduction o
7、r networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84111 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN cla
8、ss level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 84111 01 X X Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type(s). The device ty
9、pe(s) identify the circuit function as follows: Device type Generic number Circuit function Access time 01 27256-35 32K X 8-bit UV EPROM 350 ns 02 27256-25 32K X 8-bit UV EPROM 250 ns 03 27256-20 32K X 8-bit UV EPROM 200 ns 04 27256-17 32K X 8-bit UV EPROM 170 ns 05 27256-30 32K X 8-bit UV EPROM 300
10、 ns 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. Outline letter Descriptive designator Terminals Package style Y GDIP1-T28 or CDIP2-T28 28 dual-in-line package 1/ Z CQCC1-
11、N32 32 rectangular chip carrier package 1/ 1.3 Absolute maximum ratings. Supply voltage (VCC) 2/ . -0.6 V dc to +6.5 V dc Storage temperature range -65C to +150C Maximum power dissipation (PD) . 1.0 W Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) . See MIL-
12、STD-1835 Junction temperature (TJ) . +150C All input or output voltages with respect to ground -0.6 V dc to +6.5 V dc Voltage on pin A9with respect to ground . -0.6 V dc to +13.5 V dc VPPsupply voltage with respect to ground . -0.6 V dc to +13.0 V dc 1.4 Recommended operating conditions. Case operat
13、ing temperature range (TC) . -55C to +125C Input low voltage (VIL) . -0.1 V dc to +0.8 V dc Input high voltage (VIH) 2.0 V dc to VCC+1 V dc Supply voltage (VCC) . 4.5 V dc to 5.5 V dc High level program input voltage VIN(PR). 12.5 V dc 0.3 V dc (program method B) 1/ Lid shall be transparent to permi
14、t ultraviolet light erasure. 2/ All voltages referenced to VSS. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84111 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 3 DSCC FORM 223
15、4 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or
16、contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE H
17、ANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA
18、 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.
19、3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified ma
20、nufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Manag
21、ement (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify w
22、hen the QML flow option is used. (This drawing has been modified to allow the manufacturer to use the alternate die/fabrication requirements of paragraph A.3.2.2 of MIL-PRF-38535 or other alternative approved by the qualifying activity.) 3.2 Design, construction, and physical dimensions. The design,
23、 construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.2 Block diagram The block diagram shall be as specified on figure 2. 3.2.3 Truth table(s). The truth table
24、(s) shall be as specified on figure 3. 3.2.4 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the f
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLASMD596284111REVF2010MICROCIRCUITMEMORYDIGITAL262144BIT32KX8UVERASEABLEPROMMONOLITHICSILICONPDF

链接地址:http://www.mydoc123.com/p-698739.html