DLA MIL-T-36202 B-1977 TABLE SURGICAL INSTRUMENT AND SURGICAL DRESSING《手术器械和外科敷料台》.pdf

《DLA MIL-T-36202 B-1977 TABLE SURGICAL INSTRUMENT AND SURGICAL DRESSING《手术器械和外科敷料台》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-T-36202 B-1977 TABLE SURGICAL INSTRUMENT AND SURGICAL DRESSING《手术器械和外科敷料台》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、NI L-T-35202B 18 August 1977 SUPERSEDING MIL-T-36202A 9 December 1969 hl1 L ITARY SPEC IF KATION TABLE, SURGICAL INSTRUMENT AND SURGICAL DRESSING This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers corrosi

2、on-resisting steel, surgical instrument and surgical dressing tables, suitable for use in military medical f aci 1 i ti es. 1.2 Classification. The surgical instrument and surgical dressing tables shall be of the following types, as specified (see 6.2): Type I - 20 by 16 by 34-1/2 inches with one dr

3、awer. Type II - 48 by 24 by 40-1/2 inches with two drawers. 2. APPLICABLE DOCUMENTS 2.1 Issues of documents. The following documents of the issue in effect on date of invitation for bids or request for proposals, form a part of this specification to the extent specified herein. SPECIFICATIONS FEDERA

4、L FF-C-77 - Casters, Rigid and Swivel (Institutional Duty). PPP-B-636 - Boxes, Shipping, Fi berboard. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Headquarters, Defense Personnel Support Cent

5、er, ATTN: Directorate of Medical Materiel, Code ATT, 2800 South 20th Street, Philadelphia, PA 19101, by using the self-addressed Standardization Cocument Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. FSC 6530 Provided by IHSNot for ResaleNo reproduction or n

6、etworking permitted without license from IHS-,-,-shall apply. AMERICAN IRON AND STEEL INSTITUTE (AISI) AISI Steel Products Manual - Stainless and Heat Resistant Steels. (Application for copies should be addressed to the American Iron and Steel Institute, 1000 16th St. N.W.s Washington, DC 20036). NA

7、TIONAL FIRE PROTECTION ASSOCIATION (NFPA) No, 56A Standard for the Use of Inhalation Anesthetics (Application for copies should be addressed to the National Fire Protection Association, 470 Atlantic Avenue, Boston, MA 02210. ) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted wi

8、thout license from IHS-,-,- 3. REQUIREMENTS 3.1 First article. When specified in the procurement document, the contractor shall furnish sample unit(s) for first article inspection and approval (see 4.1.2.1 and 6.2) 3.2 Ma ter i al s. 3.2.1 Corrosion-resisting steel. Corrosion-resisting steel shall c

9、omply with the AISI Type 300 series as indicated in the AISI steel products manual when tested as specified in 4.4.1. 3.3 Construction. Construction shall be in accordance with Defense Personnel Support Center (DPSC) Drawing Mo. 20532. Unless otherwise specified the material used in the manufacture

10、of the table shall be corrosion-resisting steel. The table shall consist of four tubular uprights or legs fitted with casters, a top. working surface with guardrail a drawer, or drawers, located directly beneath the top and enclosed in a housing, and a lower shelf. The table shall be of the straight

11、-line, sanitary, flush construction, all parts closely fitted, welded throughout, durable and sound in every detail. The entire structure shall be properly reinforced and deslgned to minimize vibration when in motion. Gages specified herein are minimum; Unless otherwise specified, commercial toleran

12、ces shall be al lowed. need not be hemmed providing they are machined such that no sharp edges are present. The drawer housing flanges :She top shall be constructed of corrosion-resisting steel with all 3-3*1 edges 3 anged as shown on the drawing. The corners of the top shall be . rounded to fit th

13、contour of the housing. The top for the type II table shall be reinforced with longitudinal or lateral channels, as shown in DPSC Drawing No. 20532. The tog shall be fitted tightly over the drawer housing and shall be held in position by the guardrail screws. 3.3.2 Drawer housin On the type I table,

14、 the top edge of the fascia strip shall be + f ange inward 1-1/4 5 1/4 inches and the bottom edge shall be flanged inward a minimum of 3/4 inch. On the type I1 table, the tbp, bottom, and side edges of each drawer opening shall be flanged inward 1-1/4 5 1/4 inches. 3.3.3 Drawer. The drawer front sha

15、ll be filled with sound-deadening material and shallmagainst rubber bumpers. The drawer shall be provided with a pull handle made of corrosion-resisting steel, or anodized aluminum. When the drawer is closed there shall not be more than 1/16 inch clearance at any point between drawer front and enclo

16、sing frame, no more than 1/16 inch vertical movement of the drawer, and no more tnan 1/16 inch lateral movement of the drawer. The drawer face shall close flush with the front of the drawer housing. The clearance between the sides of the drawer front and the enclosing frame shall not differ by more

17、than 1/32 inch. Also, on type II tables, the clearance between the top and the bottom of the drawer front and the enclosing frame shall not differ by more than 1/32 inch. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-36202B 65 7977706 02600

18、05 T I MIL-T-36202B 3.3.4 Drawer slides. There shall be two pairs of corrosion-resisting steel slides, formed as shown on the drawing, associated with each drawer. One pair of slides, the housing slides, shall be securely welded to the back and to the front turned-in flanges of the housing. The othe

19、r air of slides shall be securely welded to the side of the drawer body. At tRe front of each housing slide and the back of each drawer body slide,- there shall be a ball bearing roller rrith a nylon facinq. .The drawer slides shall include a drawer stop to prevent inadvertent removal of the drawer.

20、 The drawer slides shall function to enable openiing and closing of the drawer without binding. 3.3.5 Guardrail. The guardrail shall be formed -from corrosion-resisting steel rod-1 be continuous around the back and sides of the tabletop. The rail shall be supported by four vertical legs, two of whic

21、h shall be formed integrally with the rail by bending the ends, the other two being separate pieces of rod continuously welded to the guardrail at appropriate locations. The guardrail shall be removable and shall be secured to the tabletop flange and the drawer housing by corrosion-resisting steel b

22、ol ts or screws, nuts and lock washers. The screw or bolt head shall be located on the outside of the table. Each guardrail shall be mounted with either all screws or all bolts. 3.3.6 Casters, Each upright of the table shall be fitted with a caster that is electrmconductive. The table, with the cast

23、ers in place, shall meet the requirements for Reduction of Electrostatic Hazards - Furniture as specified in NFPA No. 56A, when tested as specified ln 4.4.2. Casters shall be zinc or cadmium plated. Each table shall have four casters of the same size. 3.3.6.1 Type I. The four casters for the type I

24、table shall conform to type 3.3.6.2 Type II. The four casters for the type II table shall conform to the a. Two casters - Type I, class A or B, 3 inch, style a, mounted in a solid stem, fitted to the inside of the tubular upright and bolted in place. b. Two casters - Type II, class A or B, 3 inch, s

25、tyle a, mounting A or T, with brakes. II, Class A, 3 inch, style b, mounting A or T of FF-C-77. following requirements of FF-C-77: 3.4 Finish. All normally visible surfaces of the table, including interior as well as exterior surfaces of drawer, shall be given a No. 4 commercial finish. All other su

26、rfaces shall be cleaned and finished in accordance with best commercial practice. 3.5 Identification marking. Each unit shall be marked permanently and legibly with the following: Contract or purchase order number. Name or registered trademark of the manufacturer. National Stock Number. 4 Provided b

27、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-operation, maintenance, cleaning and lists of components parts. 3.7 Workmanship. Workmanship shall be first class throughout. Tables shall be free from defects which detract from their appearance or may impair th

28、eir serviceability. All burrs and sharp edges shall be removed. 3.7.1 WelGiFg. Welding shall be durable, sound in every detail and in accordance wit the latest practices recommended by the American Welding Society. All welds shall be produced by qualified welding operators with satisfactory welding

29、equipment using satisfactory filier metal or electrode where applicable to provide the best possible weld. Surfaces to be welded shall be free from grease, oil, oxides or any other foreign matter. Any cleaning method which will remove these substances and leave the surface clean is satisfactory. All

30、 weld joints shall blend into the adjacent metal in gradual, smooth curves. Beads shall be smooth and free of slag, excessive undercut, or excessive splatter. Sufficient metal shall be added to provide a suitable fillet or reinforcement unless otherwise specified. Welds shall not be oxidized. All we

31、lds shall be continuous with no visible voids, pin holes, or cracks. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract, the contractor ia responsible for the performance of all inspection requirements as specified herein. contract, the cont

32、ractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed nece

33、ssary to assure supplie5 and services conform to prescribed requirements. 4.1.1 Records. Records of exarrinations and tests performed by or for the contractor shall be maintained by the contractor and made available to the Government, upon the Governments request, at any time, or from time to time,

34、during the performance of the contract and for a period of three years after delivery of the supplies to which such records relate. 4.1.2 Inspection, Inspection, as used in this specification, is defined as both examination (such as visual and auditory investigation without the use of special labora

35、tory appliances or procedures) and testing (deter- mination by technical means of physical and chemical properties) of the item. Except as otherwise specified in the 4.1.2.1 Classification of inspection. The inspection requirements specified herein are classified as follows: .- a. First article insp

36、ection. b. Qual i ty conformance inspection. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MI L-T-36202B 4.1.2.1.1 performed on This inspect First article inspection. First article inspection shall be tables when a first article sample is require

37、d (see 3.1). on shall include examination of 4.3 and tests of 4.4. 4.1.2.1.2 Quality conformance inspection. Qua shall include the examination of 4.3 and tests of 4.1.3 Certificate of quality. certificates of manufacturer of the materials may be furnished in of such testing by the contractor, Drovid

38、ed lot i i ty conformance inspect i on 4.4. quality, supplied by the lieu of actual performance entity has been maintained and can be demnstrated to the Government. The certificate shall include the name of the contractor, the contract number, the name of the manufacturer or suppljer, the NSN, the I

39、tem Identification, the name of the component/ material, the lot number, the lot size, the sample size, the date of testing, the test method, individual test results, and the specification requirements. 4.2 Sampl i ng. 4.2.1 For examination. Sampling for examination shall be conducted in accordance

40、with MIL -S6105 and table I. The unit of product for sampling purposes shall be one table. TABLE I. Sampling for examination. 7 Inspect i on AQL (defects per 1 eve1 hundred units) For visual exam Major defects Total defects combined) For di mens i o na 1 nation (Major and M exam1 nati on II nor 1 s-

41、 1 1 1.0 4. O 2.5 be 4.2.2 For tests. Sampling for the electrical conductivity test shall conducted on 100% of the lot and the acceptance number shall heraero. The unit of product for sampling purposes shall be one table. 4,2,3 Raw materials. A sufficient quantity of each lot of corrosion- resisting

42、 steel used in the manufacture of the tables shall be selected for chemical analysis as specified in 4.4.1. wsth all requirements contained in this specification. 4.3 Examination. The tables shall be examined to determine compliance 6 Provided by IHSNot for ResaleNo reproduction or networking permit

43、ted without license from IHS-,-,-4.3.1 Classification of defects. Examination shall be conducted in accordance with the classification of defects listed in table II. Exam- ination shall not be restricted to the classified possible defects listed bel ow. Categories Major: 101 102 103 104 105 106 107

44、108 109 110 111 112 113 Mi nor: 201 202 2 03 204 205 206 207 208 TABLE II. classification of defects. Defects Components not properly aligned and fitted. Metal parts not free of cracks, tears, ruptures, and Any edge not flanged or hemmed as specified. Any weld cracked, broken, or not sound. Any join

45、t between shelf corner and upright not closely Caster cracked, broken, or not securely attached. Any component missing. Front of drawer not flush with front surface of drawer Drawer does not slide freely. Drawer not provided with stops to prevent inadvertent Any screw stripped, missing, or loose. Sw

46、ivel caster does not swivel (where required). Caster does not lock (where required). deformed surfaces (check hemmed edges). fitted. housing. removal Any exposed or accessible edge, corner, or surface not Finish not uniform; not free of coarse grind marks and Any weld not continuous, not cleaned, no

47、t free of pitting, Any exposed weld not ground smooth to blend with adjacent Unit not clean. Identification marking missing, incomplete, i 11 egi bl e , or Bumpers not provided to prevent drawer front from metal- free of burrs, sharpness, and sharp projections. scratched areas. splatter, and discolo

48、ration. surfaces. not permanently attached. to-metal coptact with the-husin . Sund-deadening material missing a rom drawer front. - 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ments of MIL-STD-129: 5. PACKAGING 5.1 Preservati on-pac kagi ng. Pr

49、eservat i on-pac kag C, as specified, (See 6.2). 5.1.1 Unit of issue. One table of the type spec unit of issue. ng shall be level A or f ied consti tutes one MIL-T-36202B 4.3.2 Dimensional examination. The tables shall be examined for defects in dimensions. Any dimension not within the tolerances specified herein shall be classified as a defect. 4.4 Tests. Tests shall be conducted to determine compliance with spec- i fi cati on re