DLA MIL-PRF-83446 37 A-2011 COILS RADIO FREQUENCY CHIP OPEN CONSTRUCTION SURFACE MOUNT 0805 SIZE.pdf

《DLA MIL-PRF-83446 37 A-2011 COILS RADIO FREQUENCY CHIP OPEN CONSTRUCTION SURFACE MOUNT 0805 SIZE.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-83446 37 A-2011 COILS RADIO FREQUENCY CHIP OPEN CONSTRUCTION SURFACE MOUNT 0805 SIZE.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5950 MIL-PRF-83446/37A 16 September 2011 SUPERSEDING MIL-PRF-83446/37 6 June 2003 PERFORMANCE SPECIFICATION SHEET COILS, RADIO FREQUENCY, CHIP, OPEN CONSTRUCTION, SURFACE MOUNT, 0805 SIZE This specification is approved for use by all Departments and Agencies of the Department of Defense

2、. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-83446. INCHES MILLIMETERS A B C D E F 0.095 Max. 0.070 Max. 0.060 Max. 0.050 (Ref. Only) 0.017 (Ref. Only) 0.008 (Ref. Only) 2.41 Max. 1.78 Max. 1.52 Max. 1.27 (Ref. Only) 0.43 (Ref. O

3、nly) 0.20(Ref. Only) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. FIGURE 1. Dimensions and configuration. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83446/37A 2 TABLE I. Ele

4、ctrical characteristics (initial). Dash Number Inductance nH 1/ Inductance Tolerance Percent () Inductance Test Frequency MHz Q (min) 1/ Q Test Frequency (MHz) Self Resonant Frequency MHz (min) 2/ DC Resistance Ohms (max) Current Rating mA (max) -01 -02 -03 -04 -05 -06 -07 -08 -09 -10 -11 -12 -13 -1

5、4 -15 -16 -17 -18 -19 -20 -21 -22 -23 -24 -25 -26 -27 -28 -29 -30 -31 -32 -33 -34 2.2 2.7 3.3 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 1800 2200 5, 10 5, 10 5, 10 10 5, 10 5, 10 5, 10 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2

6、, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 250 250 250 250 250 250 250 250 250 250 250 250 250 250 250 250 250 250 150 150 150 100 100 100 100 100 100 100

7、100 50 25 25 7.9 7.9 55 55 50 60 60 60 55 60 65 50 50 55 55 60 60 60 50 50 55 55 45 45 45 45 40 40 40 40 40 40 15 15 15 15 1800 1800 1500 1500 1500 1500 1500 1500 500 500 500 500 500 500 500 500 500 500 500 500 250 250 250 250 200 200 200 200 200 200 25 25 7.9 7.9 6000 6000 6000 5000 5000 4600 4600

8、4500 4000 2800 2600 2300 2300 2000 2000 1900 1600 1500 1330 1250 1100 920 920 820 730 750 700 600 500 450 250 250 50 40 0.08 0.08 0.08 0.08 0.09 0.11 0.12 0.13 0.15 0.17 0.20 0.22 0.25 0.27 0.29 0.31 0.34 0.38 0.42 0.46 0.51 0.70 0.80 1.20 1.20 1.80 2.00 3.00 3.50 4.00 2.50 3.00 4.50 5.00 1000 1000

9、1000 1000 1000 1000 970 930 870 810 750 720 670 650 625 600 570 540 520 490 470 400 370 300 300 250 230 210 180 170 210 195 150 140 1/ Inductance and Q are tested using HP4291A or HP4287A with test fixture 16193A, or equivalent. 2/ Self resonant Frequency tested using HP8753C, or equivalent. Provide

10、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83446/37A 3 TABLE II. Electrical characteristics (final). Inspection group Allowable percent variation Qualification Inspection: Inductance 1/ Q 2/ Self-resonant Frequency 2/ DC resistance 1/ Group II

11、Group IV Group V 5 5 5 -10 -10 -10 -8 -10 - 3 (+.001 ohm) 3 (+.001 ohm) - Quality Conformance Inspection: Group C Subgroup II Subgroup IV Subgroup V 5 5 5 -10 -10 -10 -10 -8 - 2 (+.001 ohm) 3 (+.001 ohm) - 1/ From initial measurement. 2/ From specified minimum value in electrical characteristics (in

12、itial) table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83446/37A 4 REQUIREMENTS: Dimensions and configuration: See figure 1. Bond strength: Force 1 pounds. Weight: 0.025 gram maximum. Operating temperature range: -55C to +125C. Tempera

13、ture rise (at +90C): +35C. Maximum operating temperature: +125C. Altitude: 70,000 feet. Solderability: Test method S of J-STD-002, except solder preforms may be used or MIL-STD-202, method 208, test method B. Both terminals immersed simultaneously. Magnet wire and bond are excluded from solder cover

14、age. Dielectric withstanding voltage: MIL-STD-202, method 301, test voltage 200 Vrms for 5 seconds for quality conformance. Barometric pressure: MIL-STD-202, method 105, test condition C, (70,000 feet), test voltage 80 Vrms. DWV, Barometric pressure and Insulation resistance tests are to be performe

15、d with units mounted to a test substrate. Tests are moved to after visual/mechanical inspection of qualification Group I, and after electrical characteristics (initial) of subgroup II groupC. Electrical characteristics (initial): See table I. Electrical characteristics (final): See table II. Vibrati

16、on: MIL-STD-202, method 204, test condition D. During testing, each part to be monitored for electrical continuity. Any discontinuity exceeding 100 microseconds shall be cause for rejection. Mechanical shock: MIL-STD-202, method 213, test condition I. After test parts are to be inspected for mechani

17、cal damage and verified for electrical continuity. Vibration and Mechanical shock testing shall be performed as part of Group V tests for qualification (before moisture resistance) and as part of subgroup V (semiannually) for group C testing. Parts shall be mounted on test substrates. Part or Identi

18、fying Number (PIN): The PIN shall be in the following form: M83446/37 -04 A G Sequentially assigned dash Numbers (see table I) Termination finish (see MIL-PRF-83446) Inductance tolerance (see MIL-PRF-83446) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

19、-,-,-MIL-PRF-83446/37A 5 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these not

20、ations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. MIL-PRF-83446 MIL-STD-202 J-STD-002 Custodians: Preparing activity: Army -

21、 CR DLA - CC Navy - EC Air Force - 85 (Project 5950-2011-007) Review activities: Army - MI Navy - AS, OS Air Force - 19 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-