DLA MIL-DTL-62011 E-2009 PUMP FUEL ELECTRICALLY-OPERATED 24-VOLT DC IN-TANK TYPE GENERAL SPECIFICATION FOR.pdf
《DLA MIL-DTL-62011 E-2009 PUMP FUEL ELECTRICALLY-OPERATED 24-VOLT DC IN-TANK TYPE GENERAL SPECIFICATION FOR.pdf》由会员分享,可在线阅读,更多相关《DLA MIL-DTL-62011 E-2009 PUMP FUEL ELECTRICALLY-OPERATED 24-VOLT DC IN-TANK TYPE GENERAL SPECIFICATION FOR.pdf(19页珍藏版)》请在麦多课文档分享上搜索。
1、 MIL-DTL-62011E 27 July 2009 SUPERSEDING MIL-DTL-62011D 7 September 1999 DETAIL SPECIFICATION PUMP, FUEL, ELECTRICALLY-OPERATED: 24-VOLT DC, IN-TANK TYPE, GENERAL SPECIFICATION FOR This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope
2、. This specification covers electrically-operated 24-volt (V), direct current (dc), in-tank fuel pumps capable of delivering 200 gallons per hour (gph) with outlet pressure at 4 pounds per square inch gauge (psig) (see 6.1). 1.2 Part or Identifying Number (PIN). The PIN consists of the letters M, th
3、e basic specification number, specification sheet number, a dash, and the connector type. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include documents cited in other sections of this spec
4、ification or recommended for additional information or as examples. While every effort had been made to ensure the completeness of the list, document users are cautioned that they must meet all specified requirements documents cited in sections 3, 4, or 5 of this specification, whether or not the ar
5、e listed. ASMC N/A FSC 2910 Specification number Specification sheet number Cable length (inches) M 60211 /1 - 000 - H M prefix Finish Comments, suggestions, or questions on this document should be addressed to: Defense Supply Center, Columbus, Attn: DSCC-VAI, P.O. Box 3990, Columbus OH 43218-3990,
6、or emailed to FluidFlowdla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH
7、S-,-,-MIL-DTL-62011E 2 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the solic
8、itation or contract. FEDERAL STANDARD FED-STD-H28 - Screw-Thread Standards for Federal Services COMMERCIAL ITEM DESCRIPTION A-A-52557 - Fuel Oil, Diesel; For Posts, Camps, and Stations DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-DTL-16232 - Phosphate Coating, heavy, Manganese or Zinc or Base MIL-DTL-62
9、011/1 - Pump, Fuel, Electrically-operated: 24-Volt DC, In-tank Type, Top- mounted Connector, Type I MIL-DTL-62011/2 - Pump, Fuel, Electrically-operated: 24-Volt DC, In-tank Type, Side- mounted Connector, Type II DEPARTMENT OF DEFENSE STANDARDS MIL-STD-130 - Identification Marking of US Military Prop
10、erty MIL-STD-202 - Test Methods for Electronic and Electrical Component Parts MIL-STD-461 - Requirements for the Control of Electromagnetic Interference Emissions and Susceptibility MIL-STD-810 - Environmental Test Methods and Engineering Guidelines (Copies of these documents are available online at
11、 http:/assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Non-Government Publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the iss
12、ues of these documents are those cited in the solicitation or contract. ASTM INTERNATIONAL ASTM B633 - Standard Specification for Electrodeposited Coatings of Zinc on Iron and Steel ASTM B695 - Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel ASTM D471 - Standard
13、Test Method for Rubber Property-Effect of Liquids ASTM D4814 - Gasoline, Automotive, Combat ASTM F1136 - Standard Specification for Zinc/Aluminum Corrosion Protective Coatings for Fasteners ASTM G21 - Standard Practice for Determining Resistance of Synthetic Polymeric Material to Fungi (Copies of th
14、ese documents are available online at http:/www.astm.org or from the ASTM International, P.O. Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-62011E 3 SOCIETY OF AUTOMOTIVE E
15、NGINEERS, INC. (SAE) SAE-AMS 2417 - Plating, Zinc-Nickel Alloy SAE-AMS-QQ-N-290 - Nickel Plating (Electrodeposited) SAE-AMS-QQ-P-416 - Cadmium Plating (Electrodeposited) SAE-AMS-STD-753 - Corrosion-Resistant Steel Parts: Sampling, Inspection and Testing for Surface Passivation (Copies of these docum
16、ents are available online at http:/www.sae.org or from the SAE World Headquarters, 400 Commonwealth Drive, Warrendale, PA 15096-0001.) 2.4 Order of precedence. Unless otherwise noted here in or in the contract, in the event of a conflict between the text of this document and the references cited her
17、ein (except for related specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Specification sheets. The individual item requirements shall be
18、as specified herein and in accordance with the applicable specification sheet. In the event of any conflict between requirements of this specification and the specification sheets, the latter shall govern. 3.2 First article. When specified (see 6.2), a sample shall be subjected to first article insp
19、ection in accordance with 4.4. 3.3 Materials. 3.3.1 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance req
20、uirements, and promotes economically advantageous life-cycle cost. 3.3.2. Pump motor housing. The pump motor housing shall be made of CRES. 3.3.3 Pump body, mounting bracket and hardware plating. The pump body, mounting bracket and hardware shall be plated to resist corrosion, see 3.3.4 and 3.3.5. 3
21、.3.4 Cadmium plating. All steel alloys other than CRES. 3.3.4.1 Electrical cable connectors. Electronic cable connectors shall be cadmium plating in accordance with SAE-AMS-QQ-P-416, type 1, class 1. 3.3.4.2 Screws, nuts, and bolts. Screws, nuts, and bolts shall be cadmium plated in accordance with
22、SAE-AMS-QQ-P-416, type II, class 3. 3.3.4.3 Cushion retainer, pump cover, and discharge tube fitting. Cushion retainer, pump cover, and discharge tube fitting shall be cadmium plated in accordance with SAE-AMS-QQ-P-416, type I, class 2. 3.3.4.4 Cadmium is not recommended. Carbon steel material with
23、cadmium plating shall only be used when other materials and finishes specified in this document cannot meet performance requirements (see 6.5). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-62011E 4 3.3.5 Other platings. Used on electronic
24、cable connectors, screws, nuts, nuts, cushion retainer, pump cover, and discharge tube. 3.3.5.1 Zinc plating. Zinc plating shall be in accordance with ASTM B633; type II or III, Fe/Zn 5, or ASTM B695, type II, class 5. 3.3.5.2 Zinc plating hexavalent free. Zinc plating in shall be in accordance with
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMILDTL62011E2009PUMPFUELELECTRICALLYOPERATED24VOLTDCINTANKTYPEGENERALSPECIFICATIONFORPDF

链接地址:http://www.mydoc123.com/p-691044.html