DLA MIL-DTL-55302 90 F-2008 CONNECTORS PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES RECEPTACLE RIGHT ANGLE HERMAPHRODITIC CONTACT ( 100 INCH SPACING)《印刷电路组件和附件用连接器 无极性接触件(0 100英寸间隔).pdf
《DLA MIL-DTL-55302 90 F-2008 CONNECTORS PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES RECEPTACLE RIGHT ANGLE HERMAPHRODITIC CONTACT ( 100 INCH SPACING)《印刷电路组件和附件用连接器 无极性接触件(0 100英寸间隔).pdf》由会员分享,可在线阅读,更多相关《DLA MIL-DTL-55302 90 F-2008 CONNECTORS PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES RECEPTACLE RIGHT ANGLE HERMAPHRODITIC CONTACT ( 100 INCH SPACING)《印刷电路组件和附件用连接器 无极性接触件(0 100英寸间隔).pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、INCH-POUND MIL-DTL-55302/90F 20 August 2008 SUPERSEDING MIL-DTL-55302/90E 18 February 2005 DETAIL SPECIFICATION SHEET CONNECTORS, PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES: RECEPTACLE, RIGHT ANGLE, HERMAPHRODITIC CONTACT (.100 INCH SPACING) This specification is approved for use by all Departments
2、 and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-55302. AMSC N/A FSC 5935 FIGURE 1. Connector receptacle (.100 inch spacing). Provided by IHSNot for ResaleNo reproduction or networking permit
3、ted without license from IHS-,-,-MIL-DTL-55302/90F 2 Inches mm Inches mm Inches mm Inches mm .003 0.08 .098 2.49 .175 4.44 .330 8.38 .005 0.13 .100 2.54 .185 4.70 .340 8.64 .024 0.61 .102 2.59 .200 5.08 .410 10.41 .075 1.91 .120 3.05 .235 5.97 .462 11.73 .086 2.18 .125 3.18 For .054 to .070 thick pr
4、inted circuit board Dimensions Dash number Number of contacts A .006 (0.15) B .006 (0.15) C .006 (0.15) D .006 (0.15) E .006 (0.15) H .006 (0.15) N REF 01 24 1.100 (27.94) 1.236 (31.39) 1.400 (35.56) 1.900 (48.26) 2.200 (55.88) 1.270 (32.26) 02 48 2.300 (58.42) 2.436 (61.87) 2.600 (66.04) 3.100 (78.
5、74) 3.400 (86.36) 2.470 (62.74) 03 72 3.500 (88.90) 3.636 (92.35) 3.800 (96.52) 4.300 (109.22) 4.600 (116.84) 3.670 (93.22) 04 96 4.700 (119.38) 4.836 (122.83) 5.000 (127.00) 5.500 (139.70) 5.800 (147.32) 4.870 (123.70) .110 (2.79) FIGURE 1. Connector receptacle (.100 inch spacing) Continued. Provid
6、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/90F 3 For .084 to .103 thick printed circuit board Dash number Dimensions Number of contacts A .006 (0.15) B .006 (0.15) C .006 (0.15) D .006 (0.15) E .006 (0.15) H .006 (0.15) N REF 05 24 1.100
7、 (27.94) 1.236 (31.39) 1.400 (35.56) 1.900 (48.26) 2.200 (55.88) 1.270 (32.26) 06 48 2.300 (58.42) 2.436 (61.87) 2.600 (66.04) 3.100 (78.74) 3.400 (86.36) 2.470 (62.74) 07 72 3.500 (88.90) 3.636 (92.35) 3.800 (96.52) 4.300 (109.22) 4.600 (116.84) 3.670 (93.22) 08 96 4.700 (119.38) 4.836 (122.83) 5.0
8、00 (127.00) 5.500 (139.70) 5.800 (147.32) 4.870 (123.70) .123 (3.12) For .115 to .135 thick printed circuit board Dimensions Dash number Number of contacts A .006 (0.15) B .006 (0.15) C .006 (0.15) D .006 (0.15) E .006 (0.15) H .006 (0.15) N REF 09 24 1.100 (27.94) 1.236 (31.39) 1.400 (35.56) 1.900
9、(48.26) 2.200 (55.88) 1.270 (32.26) .155 (3.94) 10 48 2.300 (58.42) 2.436 (61.87) 2.600 (66.04) 3.100 (78.74) 3.400 (86.36) 2.470 (62.74) 11 72 3.500 (88.90) 3.636 (92.35) 3.800 (96.52) 4.300 (109.22) 4.600 (116.84) 3.670 (93.22) 12 96 4.700 (119.38) 4.836 (122.83) 5.000 (127.00) 5.500 (139.70) 5.80
10、0 (147.32) 4.870 (123.70) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are .010 (0.25 mm). 4. Dimensions are .162 (4.11 mm) hex across the flats by .052 deep (1.32 mm) 4 places. 5. Keying sockets shown are
11、 in positions 4 and D. FIGURE 1. Connector receptacle (.100 inch spacing) Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/90F 4 REQUIREMENTS Dimensions and configuration: See figure 1. Material and finish: Contact: 0.020 inch
12、 thick phosphor bronze in accordance with ASTM B139/B139M, composition A. Gold plate in accordance with ASTM B488, type II, code D, class 1.27, over nickel plating in accordance with MIL-DTL-38999, appendix A, class 2, 30 to 100 microinches. Insulator: ASTM D5948, type SDG-F. Keying hardware: 2 each
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMILDTL5530290F2008CONNECTORSPRINTEDCIRCUITSUBASSEMBLYANDACCESSORIESRECEPTACLERIGHTANGLEHERMAPHRODITICCONTACT100INCHSPACING

链接地址:http://www.mydoc123.com/p-691018.html