1、INCH-POUND MIL-DTL-55302/90F 20 August 2008 SUPERSEDING MIL-DTL-55302/90E 18 February 2005 DETAIL SPECIFICATION SHEET CONNECTORS, PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES: RECEPTACLE, RIGHT ANGLE, HERMAPHRODITIC CONTACT (.100 INCH SPACING) This specification is approved for use by all Departments
2、 and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-55302. AMSC N/A FSC 5935 FIGURE 1. Connector receptacle (.100 inch spacing). Provided by IHSNot for ResaleNo reproduction or networking permit
3、ted without license from IHS-,-,-MIL-DTL-55302/90F 2 Inches mm Inches mm Inches mm Inches mm .003 0.08 .098 2.49 .175 4.44 .330 8.38 .005 0.13 .100 2.54 .185 4.70 .340 8.64 .024 0.61 .102 2.59 .200 5.08 .410 10.41 .075 1.91 .120 3.05 .235 5.97 .462 11.73 .086 2.18 .125 3.18 For .054 to .070 thick pr
4、inted circuit board Dimensions Dash number Number of contacts A .006 (0.15) B .006 (0.15) C .006 (0.15) D .006 (0.15) E .006 (0.15) H .006 (0.15) N REF 01 24 1.100 (27.94) 1.236 (31.39) 1.400 (35.56) 1.900 (48.26) 2.200 (55.88) 1.270 (32.26) 02 48 2.300 (58.42) 2.436 (61.87) 2.600 (66.04) 3.100 (78.
5、74) 3.400 (86.36) 2.470 (62.74) 03 72 3.500 (88.90) 3.636 (92.35) 3.800 (96.52) 4.300 (109.22) 4.600 (116.84) 3.670 (93.22) 04 96 4.700 (119.38) 4.836 (122.83) 5.000 (127.00) 5.500 (139.70) 5.800 (147.32) 4.870 (123.70) .110 (2.79) FIGURE 1. Connector receptacle (.100 inch spacing) Continued. Provid
6、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/90F 3 For .084 to .103 thick printed circuit board Dash number Dimensions Number of contacts A .006 (0.15) B .006 (0.15) C .006 (0.15) D .006 (0.15) E .006 (0.15) H .006 (0.15) N REF 05 24 1.100
7、 (27.94) 1.236 (31.39) 1.400 (35.56) 1.900 (48.26) 2.200 (55.88) 1.270 (32.26) 06 48 2.300 (58.42) 2.436 (61.87) 2.600 (66.04) 3.100 (78.74) 3.400 (86.36) 2.470 (62.74) 07 72 3.500 (88.90) 3.636 (92.35) 3.800 (96.52) 4.300 (109.22) 4.600 (116.84) 3.670 (93.22) 08 96 4.700 (119.38) 4.836 (122.83) 5.0
8、00 (127.00) 5.500 (139.70) 5.800 (147.32) 4.870 (123.70) .123 (3.12) For .115 to .135 thick printed circuit board Dimensions Dash number Number of contacts A .006 (0.15) B .006 (0.15) C .006 (0.15) D .006 (0.15) E .006 (0.15) H .006 (0.15) N REF 09 24 1.100 (27.94) 1.236 (31.39) 1.400 (35.56) 1.900
9、(48.26) 2.200 (55.88) 1.270 (32.26) .155 (3.94) 10 48 2.300 (58.42) 2.436 (61.87) 2.600 (66.04) 3.100 (78.74) 3.400 (86.36) 2.470 (62.74) 11 72 3.500 (88.90) 3.636 (92.35) 3.800 (96.52) 4.300 (109.22) 4.600 (116.84) 3.670 (93.22) 12 96 4.700 (119.38) 4.836 (122.83) 5.000 (127.00) 5.500 (139.70) 5.80
10、0 (147.32) 4.870 (123.70) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are .010 (0.25 mm). 4. Dimensions are .162 (4.11 mm) hex across the flats by .052 deep (1.32 mm) 4 places. 5. Keying sockets shown are
11、 in positions 4 and D. FIGURE 1. Connector receptacle (.100 inch spacing) Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/90F 4 REQUIREMENTS Dimensions and configuration: See figure 1. Material and finish: Contact: 0.020 inch
12、 thick phosphor bronze in accordance with ASTM B139/B139M, composition A. Gold plate in accordance with ASTM B488, type II, code D, class 1.27, over nickel plating in accordance with MIL-DTL-38999, appendix A, class 2, 30 to 100 microinches. Insulator: ASTM D5948, type SDG-F. Keying hardware: 2 each
13、 hex nuts and washers, stainless steel, class 300 in accordance with ASTM B582, passivated in accordance with SAE-AMS2700, type 2, and 2 each keying sockets, free machining brass in accordance with ASTM B16/B16M, UNS C36000 or ASTM B121/B121M, UNS C35300, C34200 or ASTM B124/B124M, UNS C37700, ASTM
14、B36/B36M, UNS C23000, C24000, C26000 or C26800, nickel plated in accordance with MIL-DTL-38999, appendix A. For direct government procurement the keying hardware shall be assembled to the connector. For other orders the keying hardware may be furnished loose as specified in contract or order. Mounti
15、ng hardware: 2 each machine screws 2-56, 0.5 inch long, 2 flat washers, and 2 hex nuts or corrosion resistant steel, shall be furnished in a bag within the connector package for direct government orders. For other orders, the mounting hardware may be furnished loose as specified in contract or order
16、. Contact identification: The first and last contact in each row shall be identified by an alphabetical-numerical code (e.g., A01, B12). The letter designates the row and the number designates the contact position within that row. Every fifth contact in each row shall have its identification mark mo
17、lded in. Contact retention: 6 pounds. Mating and unmating: The maximum insertion force, in pounds, shall not exceed a value equal to .5 times the number of contacts, and the withdrawal force, in pounds, shall be a minimum of .11 times the number of contacts and shall not exceed the measured insertio
18、n force. Contact separation force: 1 ounce minimum. Contact resistance: The contact resistance shall not exceed 20 milliohms. Dielectric withstanding voltage: Sea level: 1,000 volts rms, 60 Hz. High altitude: 300 volts rms, 60Hz. Current rating, maximum: 5 amperes. Keying socket: When required, can
19、be easily keyed to the desired positions by using a standard type wrench. Connectors are supplied with keying sockets in 4 and D positions. Mating connectors: Shall conform to and MIL-DTL-55302/91 or MIL-DTL-55302/93 and MIL-DTL-55302/95. Part or Identifying Number (PIN): M55302/90-(dash number from
20、 figure I). Group submission: MIL-DTL-55302/92, MIL-DTL-55302/94, and MIL-DTL-55302/96. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/90F 5 Qualification: Qualification is not required for this specification sheet. First article testi
21、ng (FAT): FAT shall be in accordance with MIL-DTL-55302, qualification inspection. Sample size: 6 connectors shall be subjected to the FAT. All sample units shall be subjected to the inspections in subgroup I. The sample units shall be divided equally into 3 groups of 2 and subjected to the inspecti
22、on for their particular subgroups. Contacts shall be tested as specified in subgroup 4A or 4B as applicable. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only
23、and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced d
24、ocuments. In addition to MIL-DTL-55302, this document references the following: MIL-DTL-38999 MIL-DTL-55302/91 MIL-DTL-55302/92 MIL-DTL-55302/93 MIL-DTL-55302/94 MIL-DTL-55302/95 MIL-DTL-55302/96 ASTM B16/B16M ASTM B121/B121M ASTM B124/B124M ASTM B139/B139M ASTM B36/B36M ASTM B488 ASTM B582 ASTM D59
25、48 SAE-AMS2700 CONCLUDING MATERIAL Custodians: Preparing activity: Army CR DLA - CC DLA CC (Project 5935-2008-178) Review activities: Army AR, AT, AV, CR4, MI NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
