DLA MIL-DTL-28840 23 D-2013 CONNECTORS ELECTRICAL CIRCULAR THREADED HIGH SHOCK HIGH DENSITY SHIPBOARD BACKSHELL GLAND NUT WIRING.pdf

《DLA MIL-DTL-28840 23 D-2013 CONNECTORS ELECTRICAL CIRCULAR THREADED HIGH SHOCK HIGH DENSITY SHIPBOARD BACKSHELL GLAND NUT WIRING.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-28840 23 D-2013 CONNECTORS ELECTRICAL CIRCULAR THREADED HIGH SHOCK HIGH DENSITY SHIPBOARD BACKSHELL GLAND NUT WIRING.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, CIRCULAR, THREADED, HIGH SHOCK, HIGH DENSITY, SHIPBOARD, BACKSHELL, GLAND NUT, WIRING This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein s

2、hall consist of this specification sheet and MIL-DTL-28840. FIGURE 1. Dimensions and configurations. AMSC N/A FSC 5935 INCH-POUND MIL-DTL-28840/23D 21 November 2013 SUPERSEDING MIL-DTL-28840/23C 11 January 2010 Inches mm .032 0.81 .062 1.57 .228 5.79 .718 18.24 Provided by IHSNot for ResaleNo reprod

3、uction or networking permitted without license from IHS-,-,-MIL-DTL-28840/23D 2 NOTES: 1. Shell sizes are provided within parentheses for information and are not a part of the designator. 2. Dimensions are in inches. 3. Metric equivalents are given for information only. 4. Dimensions apply after pla

4、ting. 5. These gland nuts are used with MIL-DTL-28840/10, /11, /14 and /16. FIGURE 1. Dimensions and configurations - Continued. Designator (see note 1) A thread class 2B B dia max A (11) .750-20 UNEF 1.028 (26.11) B (13) .875-20 UNEF 1.141 (28.98) C (15) 1.000-20 UNEF 1.263 (32.08) D (17) 1.125-18

5、UNEF 1.387 (35.23) E (19) 1.250-18 UNEF 1. 513 (38.43) F (23) 1.438-18 UNEF 1.703 (43.26) G (25) 1.562-18 UNEF 1.825 (46.35) H (29) 1.876-16 UN 2.143 (54.43) J (33) 2.062-16 UNS 2.329 (59.16) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28

6、840/23D 3 REQUIREMENTS: Dimensions and configurations: See figure 1. Interface dimensions shall conform to MIL-DTL-28840. Material and finish: See table I. TABLE I. Material and finish. Material and finish designator Material Finish W Aluminum alloy in accordance with ASTM B85/B85M, ASTM B26/B26M, A

7、STM B108/B108M, ASTM B209, ASTM B211, or ASTM B221 Cadmium plate, olive drab over electroless nickel D Corrosion resistant steel in accordance with ASTM A276, ASTM A473, or ASTM A580/A580M, type 316 Cadmium plate, black 1/ F Aluminum alloy in accordance with ASTM B85/B85M, ASTM B26/B26M, ASTM B108/B

8、108M, ASTM B209, ASTM B211, or ASTM B221 Pure electro- deposited aluminum, non-reflective L Nickel fluorocarbon polymer, non-reflective S Zinc nickel, non-reflective N Corrosion resistant steel in accordance with ASTM A276, ASTM A473, or ASTM A580/A580M, type 316 Nickel fluorocarbon polymer, non-ref

9、lective R Zinc nickel, non-reflective 1/ Screws and washers shall be passivated in accordance with SAE-AMS2700, type 2. Marking: Backshell shall be identified with the manufacturers name or trademark and the Part or Identifying Number (PIN). PIN example: M28840/ 23 J W Military designator Specificat

10、ion sheet number Size Material and finish designator (See table I) RESTRICTIONS: Material and finish designators W and D are inactive for NAVSEA new design, unless approved by NAVSEA. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28840/23D

11、4 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and con

12、tractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-DTL-28840, this document references the following: MIL-DTL-28840/10 MIL-DTL-28

13、840/11 MIL-DTL-28840/14 MIL-DTL-28840/16 ASTM A276 ASTM A473 ASTM A580/A580M ASTM B26/B26M ASTM B85/B85M ASTM B108/B108M ASTM B209 ASTM B211 ASTM B221 SAE-AMS2700 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - EC Air Force - 85 DLA - CC (Project 5935-2013-121) Review a

14、ctivities: Army AV, MI Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-