DLA A-A-59368-1999 SOLDERING DESOLDERING STATION《锡焊 卸焊站》.pdf

《DLA A-A-59368-1999 SOLDERING DESOLDERING STATION《锡焊 卸焊站》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59368-1999 SOLDERING DESOLDERING STATION《锡焊 卸焊站》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、- A-A-57368 OL8054 0004487 588 METRIC 17 March 1999 A-A-59368 COMMERCIAL ITEM DESCRIPTION SOLDERINGDESOLDERING, STATION The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description describes altern

2、ating current (ac) powered, bench mounted, conduction or convection, hand held, solderingdesoldering stations with equipment and accessories specified herein. 2. CLASSIFICATION. The solderingdesoldering stations shall be of the following types, grades, classes, and temperature ranges. 2.1 Type. Type

3、 is defined as the working side for the solderingdesoldering station. The types described herein are as follows: Type1 -Reflow Type II - Thru-hole Type III - Combination 2.2 Grade. Grade is defined as idle temperature stability of the solderingdesoldering station. The grades described herein are as

4、follows: Grade A - Idle temperature stability f 2 degrees Celsius (OC) Grade B - Idle temperature stability f 5 OC Beneficial comment, recommendations, deletions, clarifications, ect., and any data which may improve this document should be sent to: Defense Supply Center Richmond, ATTN.: DSCR- VBD, R

5、ichmond, VA 23297-5610 AMSC NA FSC 3439 DISTRTBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-593b8 9038054 0004488 414 A-A-59368 2.3 Class. Class is defined as the heat

6、ing element on the soldering/desoldering station. The classes described herein are as follows: Class 1 - Conduction Class 2 - Convection Class 3 - Combination 2.4 Temperature range. Temperature range is defined as the output temperature of the soldering/desoldering station. The classes described her

7、ein are as follows: Temperature Range A - Standard - Temperatures from 230 “C through 425 “C Temperature Range B - Low - Temperatures from 180 “C through 425 “C Temperature Range C - High - Temperatures from 230 “C through 480 “C Temperature Range D - Multi-purpose - Temperatures from 180 OC through

8、 480 “C 3. SALIENT CHARACTERISTICS 3.1 Design. The soldering/desoldering stations shall consist of a power unit and attachments as described herein. The solderingdesoldering stations shall not cause electrical overstress (EOS) damage to standard components during soldering or desoldering operations.

9、 When specified (see 7.4) the soldering/desoldering stations shall be compatible with electrostatic discharge (ESD) sensitive components. 3.1.1 Optional eauipment. When specified (see 7.4), the solderingdesoldering stations shall include the following optional equipment. . I 3.1.1.1 Fume extraction.

10、 Stations with fume extraction capabilities shall evacuate solder fumes from tip working area. Filters, if required, shall be located for operator convenience during operation and replacement. 3.1.1.2 Preparation and repair capabilities. Unless otherwise specified (see 7.4), station equipped with pr

11、eparation and repair capabilities shall perform the following functions. 3.1.1.2.1 Machining. Machining shall include hand or foot controls and shall be capable of milling, drilling, grinding, and abrasive cleaning of standard electronic equipment. 3.1.1.2.2 Thermal wire stripring. The preparation a

12、nd repair system shall be capable of thermal removal of insulation from conductors without nicking the conductor. 3.1.1.2.3 Removing; conformal coating. The preparation and repair system shall be capable of thermally removing conformal coating without damaging standard electronic components. 2 Provi

13、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59368 W 90L054 0004489 350 H A-A-59368 3.1.1.2.4 Localized heating. The preparation and repair system shall be capable of localized heating for surface mount removal and heating of multilayer boards with

14、out damaging standard electronic components. 3.2 Displays and indicators. The following subparagraphs list the minimum characteristics for a stations displays and indicators. 3.2.1 Temperature displays and indicators. When required for system operations or specified (see 7.4), temperature shall be d

15、isplayed or indicated in degrees Celsius (OC). 3.2.2 Air pressure displavs and indicators. When specified (see 7.4), stations with air capabilities shall have air pressure displays or indicators. 3.2.3 Vacuum displays and indicators. When specified (see 7.4), stations with vacuum capabilities shall

16、have vacuum display or indicators. 3.3 Controls. All operator controls shall be located in a position convenient to the operator and in the operators plain view. 3.4 Temiierature range. Unless otherwise specified (see 7.4), temperature ranges are defined as follows. A soldering stations temperature

17、range may encompass the minimum and maximum of a specified temperature range and still be classified as that specified range. 3.4.1 Standard temperature range. The soldering stations operating temperatwe shall be adjustable from 230 “C through 425 OC, with an accuracy of k15 “C for conduction solder

18、ing/desoldering and *25 “C for convection soldering/desoldering. 3.4.2 Low temperature range. The soldering stations operating temperature shall be adjustable fiom 180 OC through 425 “Cy with an accuracy +15 “C for conduction soldering/desoldering and A25 “C for convection soldering/desoldering. 3.4

19、.3 High temiierature range. The soldering stations operating temperature shall be adjustable from 230 “C through 480 OC, with an accuracy kl5 OC for conduction soldering/desoldering and *50 “C for convection soldering/desoldering. 3.4.4 Multi-purpose temDerature range. The soldering stations operati

20、ng temperature shall be adjustable from 180 “C through 480 OC, with an accuracy *15 “C for conduction soldering/desoldering and *25 “C for convection soldering/desoldering. 3.5 Vacuum. Vacuum pressure when required shall be such that solder removed by desoldering will not flow, splash or migrate to

21、other locations. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59368 = 9018054 0004490 072 A-A-59368 3.6 Air flow. Airflow volume when required shall be such that soldering and desoldering can be performed at a rate of three operations per 5

22、minutes. 3.7 Power requirements. Unless otherwise specified (see 7.4), the station power requirements shall be 120 Vac at 60 Hz single phase. Power cord shall be either 2-wire polarized or 3-wire grounding type. 3.8 Solder handpiece. Unless otherwise specified (see 7.4), stations shall have one hand

23、piece. When multiple handpieces are specified each shall be separately controlled allowing simultaneous operation. 3.9 Nameplate. A nameplate shall be securely attached to each machine. Unless otherwise specified (see 7.4), the nameplate shall contain the information listed below. a. Nomenclature b.

24、 Manufacture?s name c. Machine model number d. Power inputs (volts, total amps, phase, Pequency, hertz) e. Short circuit/over current rating f. Contract numbers g. National stock number h. Date of manufacture 4. REGULATORY REQUIREMENTS 4.1 Recovered materials. The offerorcontractor is encouraged to

25、use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4.2 Environmental protection. During the manufacture of this soldering/desoldering station, materials hazardous to the ecological systems and as prohibited by t

26、he federal, state or local statutes in effect on the date of the contract shall not be used and shall not be emitted. 5. QUALITY ASSURANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this commercial item description and shall conform to the dra

27、wings, specifications, standards and quality assurance practices of the manufacturer and also shall be the same product offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 4 Provided by IHSNot for ResaleNo reproduction or networking perm

28、itted without license from IHS-,-,- A-A-59368 9038054 0004493 TO9 II A-A-59368 6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES 7.1 Part identification number (PIN). The following part identification numbering procedure is for government purpo

29、ses and does not constitute a requirement for the contractor. This is an example of the part numbering system for CID A-A-59368. A-A-59368 -3 C 2 C I Temperature A Temp. B Temp. C Temp. D Temp. Range Range A Range B Range C Range D Class 1 Class 1 2 Class 2 3 Class 3 Grade A GradeA B GradeB Standard

30、-Temperatures fiom 230C through 425C Low-Temperatures from 180C through 425C High-Temperatures fiom 230C through 480C Multi-Purpose-Temperatures from 180C through 480C Conduction Convection Combination Idle temperature stability f 2C Idle temperature stability f 5C Type 1 Type1 2 Type11 3 Type III C

31、ID number Prefix Reflow Thru-hole Combination 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-593b 9038054 0004492 945 5 A-A-59368 7.2 National stock number RJSN). The following NSN correspond to this CID. The list is not indicative of all pos

32、sible NSNs associated with this document. NSN PIN 3439-01-374-9173 3A3D 3439-0 1-379-7874 3A1C 3439-0 1-269-5494 3A3D 3439-01 -377-7760 3A3D 7.3 Intended use. Soldering/desoldering stations covered by this commercial item description are for use in electronics production sites, repair facilities, ma

33、intenance shops and training activities. 7.4 Orderine; data. Purchasers should select the preferred options and include the following information in the order. a. b. d. e. f. g. h. C. 1. j- k. 1. m. Title, number, and date of this specification. Type, grade, class and temperature range required. (se

34、e 2.) ESD compatible, if required. (see 3.1) Fume extraction, if required. (see 3.1.1) Preparation and repair system, if required. (see 3.1.1) Preparation and repair system, if different. (see 3.1.1.2) Air pressure display and indicators, if required (see 3.2.2) Vacuum display and indicators, if req

35、uired (see 3.2.3) Temperature range, if different (see 3.4) Power requirements if different. (see 3.7) Soldering handpiece, if different. (see 3.8) Name plate data, if different (see 3.9) Preservation, packing, and marking as required. (see 6.) 7.5 Referenced documents. 7.5.1 FED-STD-376, Preferred

36、Metric Units for General Use by the Federal Government, is available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191 11-5094, Telephone 800-225-3842. 7.5.2 The Federal Acquisition Regulation (FAR) may be obtained from the Superintendent of Document

37、s, U.S. Government Printing Office, Washington, DC 20402. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-593b8 = 9038054 0004493 883 m A-A-5 93 68 , MILITARY INTERESTS: Custodians Army-AL Navy - SH Air Force - 99 CIVIL AGENCY COORDINATION ACTIVITY: GSA - FSS PREPARING ACTIVITY (Project 3439-0900) DLA - GS Reviewers Air Force - 84 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-