DLA A-A-55809 B-2007 INSULATION TAPE ELECTRICAL 600V POLYVINYL CHLORIDE PRESSURE-SENSITIVE ADHESIVE《600伏特电器用聚氯乙烯压敏绝缘胶带》.pdf

《DLA A-A-55809 B-2007 INSULATION TAPE ELECTRICAL 600V POLYVINYL CHLORIDE PRESSURE-SENSITIVE ADHESIVE《600伏特电器用聚氯乙烯压敏绝缘胶带》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55809 B-2007 INSULATION TAPE ELECTRICAL 600V POLYVINYL CHLORIDE PRESSURE-SENSITIVE ADHESIVE《600伏特电器用聚氯乙烯压敏绝缘胶带》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or Defense Supply Center Richmond (DSCR), ATTN: DSCR-VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. AMSC N/A FSC 5970 INCH-POU

2、ND A-A-55809B 1 February 2007 SUPERSEDING A-A-55809A 7 April 2005 COMMERCIAL ITEM DESCRIPTION INSULATION TAPE, ELECTRICAL, 600V, POLYVINYL CHLORIDE, PRESSURE-SENSITIVE ADHESIVE The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1.

3、 SCOPE. This commercial item description (CID) covers an electrically insulating, flame retardant, cold weather resistant, polyvinyl chloride tape with pressure sensitive adhesive. This tape is intended for use as electrical insulation on joints and splices of wires and cables in an environment of u

4、p to 600 volts and 176 F (80 C). 2. CLASSIFICATION. The electrical insulation tape shall of the following thicknesses, widths, lengths, and colors: 2.1 Thickness. The tape thickness shall be one of the coded options listed in table I (see 7.3(b). TABLE I. Tape thickness. Code Thickness (in inches) A

5、 0.0070 B 0.0090 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55809B 2 2.2 Width. The tape width shall be one of the coded options listed in table II (see 7.3(c). TABLE II. Tape width. Code Width (in inches) Code Width (in inches) 1 0.250 6 1.

6、000 2 0.375 7 1.250 3 0.500 8 1.500 4 0.625 9 2.000 5 0.750 X Other (specify in acquisition order) 2.3 Length. The tape length shall be one of the coded options listed in table III (see 7.3(d). TABLE III. Tape length. Code Length (in feet) A 20 B 66 C 108 X Other (specify in acquisition order) 2.4 C

7、olor. The tape color shall be one of the coded options listed in table IV (see 7.3(e). TABLE IV. Tape color. Code Color Code Color 1 Black 6 Blue 2 Red 7 Gray 3 Orange 8 White 4 Yellow 9 Clear 5 Green 3. SALIENT CHARACTERISTICS 3.1 Materials. The tape shall meet the requirements of the ASTM D 2301,

8、“Standard Specification for Vinyl Chloride Plastic Pressure-Sensitive Electrical Insulating Tape“. 3.2 Performance. The tape shall be listed with Underwriters Laboratories Inc. (UL) as meeting the flame retardant, cold resistant, and weather resistant requirements of UL 510, “Standard for Safety for

9、 Polyvinyl Chloride, Polyethylene, and Rubber Insulating Tape“, and tested in accordance with Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55809B 3 industry standard test methods specified in ASTM D 1000, “Standard Test Methods for Pressure-Se

10、nsitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications“. 4. REGULATORY REQUIREMENTS 4.1 Recovered materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regula

11、tion (FAR). 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commerci

12、al marketplace. The government reserves the right to require proof of such conformance. 5.2 Market acceptability. The product offered must have been previously sold either to the government or on the commercial market. 6. PACKAGING 6.1 Preservation, packing, and marking. Preservation, packing, and m

13、arking shall be as specified in the acquisition order (see 7.3(f). 7. NOTES 7.1 Part or identification number (PIN). The following PIN procedure is for government purposes and does not constitute a requirement for the contractor. AA55809 - A 5 C 1 Example of reference part number: Color (see 2.4) Le

14、ngth (see 2.3) Width (see 2.2) Thickness (see 2.1) CID number AA55809-A5C1 identifies tape, 0.0070 inch thick, 0.75 inch wide, 108 feet long, black in color. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55809B 4 7.2 Sources of documents. 7.2.1

15、 ASTM standards. Copies of ASTM standards may be obtained from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959. Electronic copies of ASTM standards may be obtained from http:/www.astm.org/. 7.2.2 UL standards. Copies of UL standards may be obtained from Und

16、erwriter Laboratories Inc., 333 Pfingsten Road, Northbrook, IL 60062-2096. Electronic copies of UL standards may be obtained from http:/ 7.2.3 FAR. The FAR may be obtained from the Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954. Electronic copies of FAR documents may be obta

17、ined from http:/www.arnet.gov/far/. 7.3 Ordering data. The acquisition order should specify the following: a. CID document number, revision, title, the date of this document and the CID PIN. b. Thickness of tape (see 2.1). c. Width of tape (see 2.2). d. Length of tape (see 2.3). e. Color of tape (se

18、e 2.4). f. Preservation, packing, and marking (see 6.1). 7.4 Cross-reference data. Table V provides a cross-reference between the HH-I-595 PIN, the predecessor of A-A-55809, the A-A-55809 PIN, and the A-A-55809B PIN for each assigned NSN. TABLE V. Part number cross-reference list. NSN HH-I-595 PIN A

19、-A-55809 PIN A-A-55809B PIN 5970-00-816-6056 HH-I-595-B-108-0 AA55809-C0 AA55809-A5C1 5970-00-926-7219 HH-I-595-A-108-0 - AA55809-A3C1 5970-01-218-6290 HH-I-595-C-108-0 - AA55809-A6C1 5970-01-373-5674 HH-I-595-A-66-2 AA55809-A2 AA55809-A3A2 5970-01-373-5675 HH-I-595-A-66-4 - AA55809-A3B4 5970-01-373

20、-5676 HH-I-595-A-66-9 - AA55809-A3B8 5970-01-373-5677 HH-I-595-A-66-6 - AA55809-A3B6 5970-01-407-1140 HH-I-595-B-66-4 - AA55809-A5B4 5970-01-407-1142 - AA55809-C2 AA55809-A5B2 5970-01-407-1143 HH-I-595-B-66-5 - AA55809-A5B5 5970-01-407-1144 HH-I-595-B-108-2 - AA55809-A5C2 5970-01-407-1145 HH-I-595-B

21、-66-9 - AA55809-A5B8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55809B 5 TABLE V. Part number cross-reference list - Continued. NSN HH-I-595 PIN AA55809 PIN A-A-55809B PIN 5970-01-407-1146 HH-I-595-B-108-5 - AA55809-A5C5 5970-01-407-1147 HH-

22、I-595-B-108-4 - AA55809-A5C4 5970-01-407-1150 HH-I-595-B-108-6 - AA55809-A5C6 5970-01-407-2881 HH-I-595-B-66-6 AA55809-C6 AA55809-A5B6 5970-01-472-1355 HH-I-595-A-66-0 AA55809-A0 AA55809-A3A1 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: Army - AR Navy - SH Air Force - 99 GSA -

23、 FSS Review Activity: Air Force - 84 Preparing Activity: DLA - GS2 (Project 5970-2006-004) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-