DIN ISO 18421-2016 Ships and marine technology - Inland navigation vessels - Lifebuoy housings (ISO 18421 2016)《船舶与海洋技术 内河航行船只 救生圈罩套(ISO 18421-2016)》.pdf

《DIN ISO 18421-2016 Ships and marine technology - Inland navigation vessels - Lifebuoy housings (ISO 18421 2016)《船舶与海洋技术 内河航行船只 救生圈罩套(ISO 18421-2016)》.pdf》由会员分享，可在线阅读，更多相关《DIN ISO 18421-2016 Ships and marine technology - Inland navigation vessels - Lifebuoy housings (ISO 18421 2016)《船舶与海洋技术 内河航行船只 救生圈罩套(ISO 18421-2016)》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、August 2016 English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 47.020.50; 47.060!%Ylo“2547376www.

2、din.deDIN ISO 18421Ships and marine technology Inland navigation vessels Lifebuoy housings (ISO 18421:2016),English translation of DIN ISO 18421:2016-08Schiffe und Meerestechnik Fahrzeuge der Binnenschifffahrt Gehuse fr Rettungsringe (ISO 18421:2016),Englische bersetzung von DIN ISO 18421:2016-08Nav

3、ires et technologie maritime Bateaux de navigation intrieure Coffres boue de sauvetage (ISO 18421:2016),Traduction anglaise de DIN ISO 18421:2016-08www.beuth.deDocument comprises 9 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritativ

4、e.08.16 A comma is used as the decimal marker. National foreword 3Introduction 51 Scope . 62 Normative references 63 Terms and definitions . 64 Requirements 64.1 Dimensions . 64.2 Design . 74.2.1 Interior . 74.2.2 Cover. 74.2.3 Mounting . 74.3 Material . 74.4 Resistance 74.5 Temperature stability 74

5、.6 Colour 74.7 Operational status check and seal ability 84.8 Resistance 85 Testing . 85.1 Scope and testing 85.2 Visual inspection and functional test. 85.3 Resistance 85.4 Strength test 85.5 Mounting instruction . 86 Designation 87 Marking 99Contents PageDIN ISO 18421:2016-08 2. 4National Annex NA

6、 (informative) Bibliography9National foreword This standard (ISO 18421:2016) has been prepared by Technical Committee ISO/TC 8 “Ships and marine technology, Subcommittee SC 7 “Inland navigation vessels” and adopted unchanged as a German Standard. The responsible German body involved in its preparati

7、on was DIN-Normenausschuss Schiffs- und Meerestechnik (DIN Standards Committee Shipbuilding and Marine Technology), Working Committee NA 132-07-01 AA FA Binnenschifffahrt, Wasserfahrzeuge, Hafenanlagen (BWH) und NA 132-07 FB. The present standard is a product standard for inland waterways. Attention

8、 is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. The DIN Standards corresponding to the International Standards referred to in this document are as follows: IS

9、O 2768-1 DIN ISO 2768-1 IEC 60945 DIN EN 60945 DIN ISO 18421:2016-08 3 National Annex NA (informative)Bibliography DIN ISO 2768-1, General tolerances Tolerances for linear and angular dimensions without individual tolerance indications DIN EN 60945, Maritime navigation and radiocommunication equipme

10、nt and systems General requirements Methods of testing and required test results DIN ISO 18421:2016-08 4 IntroductionThe housing protects the lifebuoy against permanent exposure to the elements and acts as a deterrent against theft and vandalism of therein contained life-saving equipment.Lifebuoy ho

11、usings reduce the frequency of failure of the lifebuoys.DIN ISO 18421:2016-08 5 Ships and marine technology Inland navigation vessels Lifebuoy housings1 ScopeThis International Standard specifies the construction and dimensions of housing for lifebuoys.The housing serves to encase a lifebuoy to prot

12、ect it against deterioration from the elements and against vandalism.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references

13、, the latest edition of the referenced document (including any amendments) applies.ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indicationsISO 18422, Ships and marine technology Inland navigation vessels Plate with instructions for

14、rescue, resuscitation and first aid for drowning personsIEC 60945, Maritime navigation and radiocommunication equipment and systems General requirements Methods of testing and required test results3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.3.1

15、lifebuoybuoyant ring provided with grab lines (3.2) and reflective stripsNote 1 to entry: A lifebuoy enables a person to keep himself above water, marks the location of the emergency, and aids recovery. Lifebuoys can be fitted with lines and light sources in accordance with official regulations.3.2g

16、rab linefibre rope for seizing and grabbing the lifebuoy (3.1) in water4 Requirements4.1 DimensionsGeneral tolerances: ISO 2768-cEdges shall be rounded with: min. R = 0,3 mm.NOTE Radius is given to prevent clothing getting caught.The internal dimensions are to be chosen so that a lifebuoy of 760 mm

17、outer diameter, 440 mm inner diameter and of 103 mm thickness with a grab line at its outer edge and a floatable line with a diameter of 8 mm to 11 mm and 30 m length, with or without throw line, fits into the housing.DIN ISO 18421:2016-08 6 4.2 Design4.2.1 InteriorThe interior of the housing shall

18、be designed so that neither the lifebuoy nor the life-line will fall off when the cover is opened and at the same time allows quick and easy access to both.4.2.2 CoverThe housing shall have a cover with bolting. The cover shall have a captive connection to the housing. The closing latches shall keep

19、 the door shut, but allow quick and easy access the lifebuoy.The design of the cover shall allow an easy access of the life buoy.The cover of the housing shall have a lifebuoy symbol to the outside and the plate with directions for rescue and resuscitation of drowning persons in accordance with ISO

20、18422 shall be fastened inside the inner circle of the lifebuoy symbol.4.2.3 MountingThe housing for lifebuoys shall be manufactured in such a way that it can be fixed to masts, posts and poles or onto walls or railings.These requirements are met if there are four bolt holes for the fixing of the ho

21、using through which threaded bolts can be inserted.4.3 MaterialThe housing shall be of a suitable material, e.g.: plastics (Pl); seawater-resistant aluminium (Al); hot-dip galvanised steel (HDG); stainless steel (Stst).4.4 ResistanceThe housing shall comply with the requirements in accordance with I

22、EC 60945 regarding the following:a) rain and spray water;b) sun radiation;c) resistance against oil;d) corrosion.4.5 Temperature stabilityThe utilizability of the housing shall remain constant at air temperatures of 25 C to +65 C.4.6 ColourThe external surface of the housing shall be orange or red.D

23、IN ISO 18421:2016-08 7 4.7 Operational status check and seal abilityThe housing may be fitted with an indicating device at the front, whether a lifebuoy is inside the housing or not.The housing may allow for an indicating seal to be used.4.8 ResistanceThe housing shall have sufficient strength. Test

24、ing shall be according to 5.4.5 Testing5.1 Scope and testingType approval test on one housing shall be carried out.The tests shall include the following individual tests as described below. The test is performed by visual inspection, function test and measuring.5.2 Visual inspection and functional t

25、estThe performance, the quality of the surface, the colour, the functioning of the indicating device, if applicable, and the feasibility to attach an indicating seal, if applicable, shall be tested by visual inspection and function test.5.3 ResistanceThe manufacturer shall present certificates provi

26、ng that the relevant requirements in 4.4 and 4.5 are fulfilled.5.4 Strength testThe test shall be carried out at an ambient temperature of +20 C 5 C.Prior to the test the housing shall be fixed according to the manufacturers instruction. The housing shall be filled with lifebuoy and the line as desc

27、ribed in 4.1 and closed.Then a textile belt of a width of 35 mm 5 mm with means for attaching the test weight shall be placed around the housing. With this, the test weight of 100 kg shall be applied to the belt and maintained for 60 s.During and after the test, the housing shall neither become loos

28、ened from the fixation nor show any malfunction nor permanent deformation or damage.5.5 Mounting instructionThe manufacturer shall provide mounting instructions.6 DesignationFor the designation of material, the material abbreviation in 4.3 shall be used.Designation of a lifebuoy housing in accordance with this International Standard, material plastic Pl (Pl):Lifebuoy housing ISO 18421 PlDIN ISO 18421:2016-08 8 7 MarkingThe housing shall be permanently marked with the following details:a) a reference to this International Standard, i.e. ISO 18421;b) year of manufacture.DIN ISO 18421:2016-08 9