DIN ISO 12164-4-2016 Hollow taper interface with flange contact surface - Part 4 Dimensions of receivers for stationary tools (ISO 12164-4 2014)《带法兰连接表面的中空锥形接口 第4部分 固定式工具承受器的尺寸(ISO.pdf
《DIN ISO 12164-4-2016 Hollow taper interface with flange contact surface - Part 4 Dimensions of receivers for stationary tools (ISO 12164-4 2014)《带法兰连接表面的中空锥形接口 第4部分 固定式工具承受器的尺寸(ISO.pdf》由会员分享,可在线阅读,更多相关《DIN ISO 12164-4-2016 Hollow taper interface with flange contact surface - Part 4 Dimensions of receivers for stationary tools (ISO 12164-4 2014)《带法兰连接表面的中空锥形接口 第4部分 固定式工具承受器的尺寸(ISO.pdf(9页珍藏版)》请在麦多课文档分享上搜索。
1、October 2016 English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 25.060.20!%nc“2577564www.din.deDI
2、N ISO 12164-4Hollow taper interface with flange contact surface Part 4: Dimensions of receivers for stationary tools (ISO 121644:2014),English translation of DIN ISO 12164-4:2016-10Hohlkegelschnittstelle mit Plananlage Teil 4: Mae von Aufnahmen fr stehende Werkzeuge (ISO 121644:2014),Englische berse
3、tzung von DIN ISO 12164-4:2016-10Interfaces cne creuxface Partie 4: Dimensions des nez de broches pour outils non rotatifs (ISO 121644:2014),Traduction anglaise de DIN ISO 12164-4:2016-10www.beuth.deDocument comprises 9 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language or
4、iginal shall be considered authoritative.09.16 A comma is used as the decimal marker. Contents PageNational foreword31 Scope .42 Normative references 43 Dimensions .43.1 General .43.2 Receiver for hollow taper shank, type T .44 Design Hole for manual clamping .65 Designation 6Annex A (informative) R
5、ecommendations for use and application .8Bibliography 9National Annex NA (informative) Bibliography .3DIN ISO 12164-4:2016-102 National foreword This document (ISO 12164-4:2014) has been prepared by Technical Committee ISO/TC 29 “Small tools (Secretariat: AFNOR, France). The responsible German body
6、involved in its preparation was DIN-Normenausschuss Werkzeuge und Spannzeuge (DIN Standards Committee Tools and Clamping Devices), Working Committee NA 121-02-05 AA Werkzeugaufnahmen und Schnittstelle Maschine/Werkzeug. Attention is drawn to the possibility that some of the elements of this document
7、 may be the subject of patent rights. DIN and/or DKE shall not be held responsible for identifying any or all such patent rights. ISO 12164 consists of the following parts, under the general title Hollow taper interface with flange contact surface: Part 1: Shanks Dimensions Part 2: Receivers Dimensi
8、ons Part 3: Dimensions of shanks for stationary tools Part 4: Dimensions of receivers for stationary tools The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 1101 DIN EN ISO 1101 ISO 2768-1 DIN ISO 2768-1 ISO 3040 DIN EN ISO 3040 National
9、Annex NA(informative) Bibliography DIN EN ISO 1101, Geometrical Product Specifications (GPS) Geometrical tolerancing Tolerances of form, orientation, location and run-out DIN ISO 2768-1, General tolerances; tolerances for linear and angular dimensions without individual tolerance indications DIN EN
10、ISO 3040, Geometrical product specifications (GPS) Dimensioning and tolerancing Cones DIN ISO 12164-4:2016-103 Hollow taper interface with flange contact surface Part 4: Dimensions of receivers for stationary tools1 ScopeThis part of ISO 12164 specifies dimensions for receivers with taper and flange
11、 contact surfaces for hollow taper shanks in accordance with ISO 12164-3 to be applied to machine tools (e.g. turning machines, turning-mill machines). A range of sizes is specified.This part of ISO 12164 specifies the receiver of type T. It is for automatic tool exchange and manual clamping, which
12、is achieved via holes in both the receiver and the tool shank.The torque is transmitted via the tail end of the shank through keys as well as friction.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its applica
13、tion. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 1101, Geometrical product specifications (GPS) Geometrical tolerancing Tolerances of form, orientation, location and run-outISO 276
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DINISO1216442016HOLLOWTAPERINTERFACEWITHFLANGECONTACTSURFACEPART4DIMENSIONSOFRECEIVERSFORSTATIONARYTOOLSISO1216442014

链接地址:http://www.mydoc123.com/p-683971.html