DIN EN ISO 22391-1-2010 Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 1 General (ISO 22391-1 2009) Ger.pdf

《DIN EN ISO 22391-1-2010 Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 1 General (ISO 22391-1 2009) Ger.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 22391-1-2010 Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 1 General (ISO 22391-1 2009) Ger.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、April 2010 Translation by DIN-Sprachendienst.English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS

2、91.140.60!$aS“1626148www.din.deDDIN EN ISO 22391-1Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 1: General (ISO 22391-1:2009)English translation of DIN EN ISO 22391-1:2010-04Kunststoff-Rohrleitungssysteme fr die Warm- und Kalt

3、wasserinstallation Polyethylen erhhter Temperaturbestndigkeit (PE-RT) Teil 1: Allgemeines (ISO 22391-1:2009)Englische bersetzung von DIN EN ISO 22391-1:2010-04Systmes de canalisations en plastique pour les installations deau chaude et froide Polythylne de meilleure rsistance la temprature (PE-RT) Pa

4、rtie 1: Gnralits (ISO 22391-1:2009)Traduction anglaise de DIN EN ISO 22391-1:2010-04www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 17 pages04.10 DIN EN ISO 22391-1:2010-04 2 A comma is used as the decimal marker. National foreword This

5、 standard has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids”, Subcommittee SC 2 “Plastics pipes and fittings for water supplies” (Secretariat: SNV, Switzerland) in collaboration with Technical Committee CEN/TC 155 “Plastics piping sy

6、stems and ducting systems” (Secretariat: NEN, Netherlands). The responsible German body involved in its preparation was the Normenausschuss Wasserwesen (Water Practice Standards Committee), Joint Working Committees NA 119-04-06 GA Kunststoffrohre in der Trink-wasserversorgung and NA 119-04-06-05 GUA

7、 Warm- und Kaltwasserleitungen. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. ISO 22391 consists of the following parts1), under the general title

8、Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT): Part 1: General Part 2: Pipes Part 3: Fittings Part 5: Fitness for purpose of the system The DIN Standards corresponding to the International Standards referred to in clause 2 of the E

9、N are as follows, whereby EN ISO Standards are only listed below if these have not been published as DIN EN ISO Standards with the same number: ISO 472 DIN EN ISO 472 ISO 1043-1 DIN EN ISO 1043-1 ISO 22391-2 DIN EN ISO 22391-2 ISO 22391-3 DIN EN ISO 22391-3 ISO 22391-5 DIN EN ISO 22391-5 1) This Sys

10、tem Standard does not incorporate a Part 4: Ancillary equipment or a Part 6: Guidance for installation. For ancillary equipment, separate standards can apply. Guidance for installation of plastics piping systems made from different materials, intended to be used for hot and cold water installations,

11、 is covered by ENV 12108. DIN EN ISO 22391-1:2010-04 3 National Annex NA (informative) Bibliography DIN EN ISO 472, Plastics Vocabulary DIN EN ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics DIN EN ISO 22391-2, Plastics piping systems for h

12、ot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 2: Pipes DIN EN ISO 22391-3, Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 3: Fittings DIN EN ISO 22391-5, Plastics piping systems for

13、hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 5: Fitness for purpose of the system DIN EN ISO 22391-1:2010-04 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 22391-1 December 2009 ICS 23.040.01; 91.140.60; 93.0

14、25 English Version Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 1: General (ISO 22391-1:2009) Systmes de canalisations en plastique pour les installations deau chaude et froide - Polythylne de meilleure rsistance la tempr

15、ature (PE-RT) - Partie 1: Gnralits (ISO 22391-1:2009) Kunststoff-Rohrleitungssysteme fr die Warm- und Kaltwasserinstallation - Polyethylen erhhter Temperaturbestndigkeit (PE-RT) - Teil 1: Allgemeines (ISO 22391-1:2009) This European Standard was approved by CEN on 4 November 2009. CEN members are bo

16、und to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the

17、CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same st

18、atus as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Roman

19、ia, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved w

20、orldwide for CEN national Members. Ref. No. EN ISO 22391-1:2009: EContents Page Foreword3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms, definitions, symbols and abbreviated terms6 3.1 Terms and definitions .6 3.2 Symbols 9 3.3 Abbreviated terms 10 4 Classification of service conditions

21、 . 11 5 Material 12 5.1 General. 12 5.2 Influence on water intended for human consumption 12 5.3 Reprocessable material . 12 6 System performance requirement 12 Bibliography. 13 DIN EN ISO 22391-1:2010-04 EN ISO 22391-1:2009 (E) 2 Foreword “Plastics piping systems and ducting systems” the secretaria

22、t of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2010, and conflicting national standards shall be withdrawn at the latest by June 2010. Attention is drawn to the po

23、ssibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries

24、 are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, S

25、weden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 22391-1:2009 has been approved by CEN as a EN ISO 22391-1:2009 without any modification. This document (EN ISO 22391-1:2009) has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the

26、transport of fluids” in collaboration with Technical Committee CEN/TC 155 DIN EN ISO 22391-1:2010-04 EN ISO 22391-1:2009 (E) 3 Introduction The System Standard, of which this is Part 1, specifies the requirements for a piping system and its components when made from polyethylene of raised temperatur

27、e resistance (PE-RT). The piping system is intended to be used for hot and cold water installations. In respect of potential adverse effects on the quality of water intended for human consumption caused by the products covered by ISO 22391, the following are relevant. a) This part of ISO 22391 provi

28、des no information as to whether the products can be used without restriction. b) Existing national regulations concerning the use and/or characteristics of the products remain in force. This part of ISO 22391 specifies the general aspects of the plastics piping system. At the date of publication of

29、 this part of ISO 22391, System Standards Series for piping systems of other plastics materials used for the same application are the following: ISO 15874 (all parts), Plastics piping systems for hot and cold water installations Polypropylene (PP) ISO 15875 (all parts), Plastics piping systems for h

30、ot and cold water installations Crosslinked polyethylene (PE-X) ISO 15876 (all parts), Plastics piping systems for hot and cold water installations Polybutylene (PB) ISO 15877 (all parts), Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) DIN EN IS

31、O 22391-1:2010-04 EN ISO 22391-1:2009 (E) 4 1 Scope This part of ISO 22391 specifies the general characteristics of piping systems made of polyethylene of raised temperature resistance (PE-RT), Type I, and polyethylene of raised temperature resistance (PE-RT), Type II, intended to be used for hot an

32、d cold water installations within buildings for the conveyance of water, whether or not the water is intended for human consumption (domestic systems) and for heating systems, under specified design pressures and temperatures appropriate to the class of application. This part of ISO 22391 covers a r

33、ange of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and defines terms. In conjunction with the other parts of ISO 22391, it is applicable to PE-RT pipes, fittings, their joints and to joints having components of PE-RT,

34、as well as of other plastics and non-plastics materials, respectively, used for hot and cold water installations. It is not applicable to values of design temperature, maximum design temperature or malfunction temperature in excess of those it specifies. NOTE It is the responsibility of the purchase

35、r or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. 2 Normative references The following referenced documents are indispensable for the application of this d

36、ocument. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 472, Plastics Vocabulary ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteri

37、stics ISO 4065, Thermoplastics pipes Universal wall thickness table ISO 22391-2, Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 2: Pipes ISO 22391-3, Plastics piping systems for hot and cold water installations Polyethylene of

38、raised temperature resistance (PE-RT) Part 3: Fittings DIN EN ISO 22391-1:2010-04 EN ISO 22391-1:2009 (E) 5 ISO 22391-5, Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 5: Fitness for purpose of the system 3 Terms, definitions,

39、symbols and abbreviated terms 3.1 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 472 and ISO 1043-1 and the following apply. 3.1.1 Geometrical terms and definitions 3.1.1.1 nominal size DN numerical designation of the size of a component, which is a c

40、onvenient round number, approximately equal to the manufacturing dimensions in millimetres (mm) 3.1.1.2 nominal size DN/OD nominal size, related to outside diameter 3.1.1.3 nominal outside diameter dnspecified diameter, in millimetres, assigned to a nominal size DN/OD 3.1.1.4 outside diameter (at an

41、y point) demeasured outside diameter through the cross-section at any point of a pipe or spigot end of a fitting, rounded up to the nearest 0,1 mm 3.1.1.5 mean outside diameter demmeasured length of the outer circumference of a pipe or spigot end of a fitting in any cross-section, divided by (= 3,14

42、2) rounded up to the nearest 0,1 mm 3.1.1.6 minimum mean outside diameter dem, minminimum value of the mean outside diameter as specified for a given nominal size 3.1.1.7 maximum mean outside diameter dem, maxmaximum value of the mean outside diameter as specified for a given nominal size 3.1.1.8 me

43、an inside diameter of socket dsmarithmetical mean of two measured inside diameters perpendicular to each other at the mid-point of the socket length DIN EN ISO 22391-1:2010-04 EN ISO 22391-1:2009 (E) 6 3.1.1.9 out-of-roundness ovality difference between the measured maximum outside diameter and the

44、measured minimum outside diameter in the same cross-sectional plane of a pipe or spigot end of a fitting, or the difference between the measured maximum inside diameter and the measured minimum inside diameter in the same cross-sectional plane of a socket 3.1.1.10 nominal wall thickness ennumerical

45、designation of the wall thickness of a component, approximately equal to the manufacturing dimension in millimetres (mm) 3.1.1.11 wall thickness e measured wall thickness at any point around the circumference of a component, rounded up to the nearest 0,1 mm 3.1.1.12 minimum wall thickness eminminimu

46、m wall thickness at any point around the circumference of a component, as specified 3.1.1.13 maximum wall thickness emaxmaximum wall thickness at any point around the circumference of a component, as specified 3.1.1.14 tolerance permitted variation of the specified value of a quantity, expressed as

47、the difference between the permitted maximum and the permitted minimum value 3.1.1.15 pipe series S dimensionless number for pipe designation conforming to ISO 4065 NOTE According to ISO 22391, the pipe series, S, is used as a means for selecting pipe sizes for practical purposes (see ISO 22391-2).

48、3.1.1.16 calculated pipe value Scalcvalue for a specific pipe calculated using Equation (1), rounded up to the nearest 0,1 mm, nncalcn2deSe= (1) where dnis the nominal outside diameter, in millimetres; enis the nominal wall thickness, expressed in millimetres. DIN EN ISO 22391-1:2010-04 EN ISO 22391

49、-1:2009 (E) 7 3.1.2 Terms and definitions related to service conditions 3.1.2.1 design pressure pDhighest pressure related to the circumstances for which the system has been designed and is intended to be used NOTE The design pressure is equivalent to the maximum design pressure, MDP, as specified in EN 806-1. 3.1.2.2 hydrostatic stress stress induced in the wall of a pipe when a pressure is applied using water as a medium, and calculated using the approximate Equation (2): em