DIN EN ISO 9692-3-2016 Welding and allied processes - Types of joint preparation - Part 3 Metal inert gas welding and tungsten inert gas welding of aluminium and its alloys (ISO 96.pdf

《DIN EN ISO 9692-3-2016 Welding and allied processes - Types of joint preparation - Part 3 Metal inert gas welding and tungsten inert gas welding of aluminium and its alloys (ISO 96.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 9692-3-2016 Welding and allied processes - Types of joint preparation - Part 3 Metal inert gas welding and tungsten inert gas welding of aluminium and its alloys (ISO 96.pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、November 2016 English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 25.160.40!%u“2588299www.din.deD

2、IN EN ISO 9692-3Welding and allied processes Types of joint preparation Part 3: Metal inert gas welding and tungsten inert gas welding of aluminium and its alloys (ISO 96923:2016);English version EN ISO 96923:2016,English translation of DIN EN ISO 9692-3:2016-11Schweien und verwandte Prozesse Arten

3、der Schweinahtvorbereitung Teil 3: MetallInertgasschweien und WolframInertgasschweien von Aluminium und Aluminiumlegierungen (ISO 96923:2016);Englische Fassung EN ISO 96923:2016,Englische bersetzung von DIN EN ISO 9692-3:2016-11Soudage et techniques connexes Types de prparation de joints Partie 3: S

4、oudage MIG et TIG de laluminium et de ses alliages (ISO 96923:2016);Version anglaise EN ISO 96923:2016,Traduction anglaise de DIN EN ISO 9692-3:2016-11SupersedesDIN EN ISO 96923:200107www.beuth.deDocument comprises 19 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language orig

5、inal shall be considered authoritative.11.16 DIN EN ISO 9692-3:2016-11 2 A comma is used as the decimal marker. National foreword This document (EN ISO 9692-3:2016) has been prepared by Technical Committee ISO/TC 44 “Welding and allied processes” in collaboration with Technical Committee CEN/TC 121

6、“Welding and allied processes” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was DIN-Normenausschuss Schweien und verwandte Verfahren (DIN Standards Committee Welding and Allied Processes), Working Committee NA 092-00-19 AA Schweien von Aluminium und anderen Le

7、ichtmetallen (DVS AG W 6). The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 2553:2013 DIN EN ISO 2553:2014-04 ISO 4063 DIN EN ISO 4063 Amendments This standard differs from DIN EN ISO 9692-3:2001-07 as follows: a) the reference numbers h

8、ave been adapted to DIN EN ISO 2553. Consequently, the amendments listed under items b) to m) refer to the weld designation; b) Table 1, square butt weld: the gap has been changed to b 1; c) Table 1, square butt weld with backing: the recommended welding process has been changed to 141*); d) Table 1

9、, single-V butt weld: recommendations for workpiece thickness 3 t 6 have been newly added; e) Table 1, single-V butt weld with broad root face: angle has been changed to 60; f) Table 1, single-bevel butt weld with backing: the gap has been changed to 3 b 8; g) Table 1, butt weld between plates with

10、raised edges: recommended welding process 142 has been newly added; h) Table 2, square butt weld: the workpiece thickness has been changed to 6 t 10 and recommended welding process 131*), has been newly added; i) Table 2, double-V butt weld with broad root face: the gap has been changed to b 1; j) T

11、able 2, single-V butt weld with broad root face and backing run: angle has been changed to 60; k) Table 2, single-bevel butt weld with backing run: recommended welding process 141*)has been deleted; l) Table 3, single fillet weld and double fillet weld: angle has been changed to 90; m) normative ref

12、erences have been updated. *)Translators note. Incorrect in original German version. It should read “131”. *)Translators note. Incorrect in original German version. It should read “141”. DIN EN ISO 9692-3:2016-11 3 Previous editions DIN 8552-1: 1981-05 DIN EN ISO 9692-3: 2001-07 National Annex NA (i

13、nformative) Bibliography DIN EN ISO 2553:2014-04, Welding and allied processes Symbolic representation on drawings Welded joints (ISO 2553:2013) DIN EN ISO 4063, Welding and allied processes Nomenclature of processes and reference numbers DIN EN ISO 9692-3:2016-11 4 This page is intentionally blank

14、EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 9692-3 July 2016 ICS 25.160.10 Supersedes EN ISO 9692-3:2001English Version Welding and allied processes - Types of joint preparation -Part 3: Metal inert gas welding and tungsten inert gas welding of aluminium and its alloys (ISO 9692-3:2016)

15、 Soudage et techniques connexes - Types de prparation de joints - Partie 3: Soudage MIG et TIG de laluminium et de ses alliages (ISO 9692-3:2016) Schweien und verwandte Prozesse - Arten der Schweinahtvorbereitung - Teil 3: Metall-Inertgasschweien und Wolfram-Inertgasschweien von Aluminium und Alumin

16、iumlegierungen (ISO 9692-3:2016) This European Standard was approved by CEN on 10 July 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date

17、 lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation u

18、nder the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Forme

19、r Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EU

20、ROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 9692-3:2016 EEuropean foreword .3Introduction 51 Scope

21、. 62 Normative references 63 Materials . 64 Welding processes 65 Finish 66 Type of joint preparation 7Contents Page2DIN EN ISO 9692-3:2016-11 EN ISO 9692-3:2016 (E) Foreword .4European foreword This document (EN ISO 9692-3:2016) has been prepared by Technical Committee ISO/TC 44 “Welding and allied

22、processes” in collaboration with Technical Committee CEN/TC 121 “Welding and allied processes” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2017

23、, and conflicting national standards shall be withdrawn at the latest by January 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights.

24、 This document supersedes EN ISO 9692-3:2001. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound

25、to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,

26、Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 9692-3:2016 has been approved by CEN as EN ISO 9692-3:2016 without any modification. 3DIN EN ISO 9692-3:2016-11 EN ISO 9692-3:2016 (E)ForewordISO (the International Organization

27、 for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has

28、the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The pro

29、cedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editor

30、ial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights

31、 identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explana

32、tion on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT), see the following URL: Foreword Supplementary information .The committee responsible for this docume

33、nt is ISO/TC 44, Welding and allied processes, Subcommittee SC 7, Representation and terms.This second edition cancels and replaces the first edition (ISO 96923:2000), which has been technically revised.ISO 9692 consists of the following parts, under the general title Welding and allied processes Ty

34、pes of joint preparation: Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels Part 2: Submerged arc welding of steels Part 3: Metal inert gas welding and tungsten inert gas welding of aluminium and its alloys Part 4: Clad steelsReques

35、ts for official interpretations of any aspect of this International Standard should be directed to the Secretariat of ISO/TC 44/SC 7 via your national standards body. A complete listing of these bodies can be found at www.iso.org.4DIN EN ISO 9692-3:2016-11 EN ISO 9692-3:2016 (E) IntroductionThis par

36、t of ISO 9692 defines the parameters characterizing the joint preparation and assembly of the most often encountered dimensions and shapes.The recommendations given in this part of ISO 9692 have been compiled on the basis of experience and contain dimensions for types of joint preparation that are g

37、enerally found to provide suitable welding conditions. However, the extended field of application makes it necessary to give a range of dimensions. The dimension ranges specified represent design limits and are not tolerances for manufacturing purposes. Manufacturing limits depend, for instance, on

38、welding process, parent metal, welding position, quality level, etc. Due to the common character of this part of ISO 9692, the examples given cannot be regarded as the only solution for the selection of a joint type.Specific fields of application and manufacturing requirements may be covered by sele

39、cted ranges of dimensions specified in the relevant application standard.5DIN EN ISO 9692-3:2016-11 EN ISO 9692-3:2016 (E)1 ScopeThis part of ISO 9692 specifies recommended types of joint preparation for metal inert gas welding, MIG (131), and tungsten inert gas welding, TIG (141), and autogenous TI

40、G welding (142) on aluminium and its alloys.It applies to fully penetrated welds.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undate

41、d references, the latest edition of the referenced document (including any amendments) applies.ISO 2553:2013, Welding and allied processes Symbolic representation on drawings Welded jointsISO 4063, Welding and allied processes Nomenclature of processes and reference numbers3 MaterialsJoint preparati

42、ons recommended in this part of ISO 9692 are suitable for all types of aluminium and its weldable alloys.4 Welding processesJoint preparations recommended in this part of ISO 9692 are suitable for welding carried out in accordance with the following processes as specified in Tables 1 to 3. Combinati

43、ons of different processes are possible: MIG welding with solid wire electrode (131); TIG welding with solid filler material (wire/rod) (TIG) (141); autogenous TIG welding (142) only applicable for butt weld between plates with raised edges (see Table 1, 1.20)NOTE The numbers in parentheses refer to

44、 the reference number of the welding process specified in ISO 4063.5 FinishEdges should be prepared by mechanical means (e.g. shearing, sawing or milling). No mineral oil-based cleaning fluids shall be used. If plasma cutting is used, consideration shall be given to the quality of cut surfaces (e.g.

45、 cracks).6DIN EN ISO 9692-3:2016-11 EN ISO 9692-3:2016 (E) The longitudinal edges of the root face should be de-burred and chamfered, especially for single-sided butt welds without backing.6 Type of joint preparationThe recommended types of joint preparation and dimensions are specified in Tables 1

46、to 3.The choice of joint details (angle, gap, thickness of root face) depends on the joint thickness, the position and the welding process. The use of larger gaps (1,5 mm) permits smaller angles.If gaps are 1,5 mm, backing is preferably used.For single-sided welding, backing bars should be grooved.T

47、he reference numbers in Tables 1 to 3 have been determined in accordance with the following scheme: the first digit corresponds with the number of the table (e.g. digit 1 for Table 1 with joint preparation for butt welds, welded from one side); the second digit or numerical group corresponds with th

48、e number in ISO 2553 (e.g. digit 2 for square butt weld as given in ISO 2553:2013, Table 1); the third indication, expressed by a letter, covers the variants of joint preparations.EXAMPLE Joint preparation for a butt weld, welded from one side (1), finished for single-V butt weld (3):1.37DIN EN ISO

49、9692-3:2016-11 EN ISO 9692-3:2016 (E)Table 1 Joint preparation for butt welds, welded from one sideDimensions in millimetresWeld Joint preparationRecommend-ed welding processcRemarksRef. No.aWorkpiece thickness tDesignation SymbolbIllustration Cross-sectionAngle , Gap bThick-ness of root face cOther dimensions1.1t 4 Square butt weld b 1 141Chamfering on the root side is rec-ommended2 t