DIN EN ISO 4018-2011 Hexagon head screws - Product grade C (ISO 4018 2011) German version EN ISO 4018 2011《六角头螺钉 产品等级C级(ISO 4018-2011) 德文版本EN ISO 4018-2011》.pdf

《DIN EN ISO 4018-2011 Hexagon head screws - Product grade C (ISO 4018 2011) German version EN ISO 4018 2011《六角头螺钉 产品等级C级(ISO 4018-2011) 德文版本EN ISO 4018-2011》.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 4018-2011 Hexagon head screws - Product grade C (ISO 4018 2011) German version EN ISO 4018 2011《六角头螺钉 产品等级C级(ISO 4018-2011) 德文版本EN ISO 4018-2011》.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、July 2011 Translation by DIN-Sprachendienst.English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 2

2、1.060.10!$s“1805659www.din.deDDIN EN ISO 4018Hexagon head screws Product grade C (ISO 4018:2011)English translation of DIN EN ISO 4018:2011-07Sechskantschrauben mit Gewinde bis Kopf Produktklasse C (ISO 4018:2011)Englische bersetzung von DIN EN ISO 4018:2011-07Vis tte hexagonale entirement filetes G

3、rade C (ISO 4018:2011)Traduction anglaise de DIN EN ISO 4018:2011-07SupersedesDIN EN ISO 4018:2001-03www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.1706.11A comma is used as the decimal marker. DIN EN ISO 4018:2011-07 National for

4、eword This standard has been prepared by Technical Committee ISO/TC 2 “Fasteners” in collaboration with Technical Committee CEN/TC 185 “Fasteners” (both secretariats are held by DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Mechanische Verbindungselem

5、ente (Fasteners Standards Committee), Working Committee NA 067-00-02 AA Verbindungselemente mit metrischem Auengewinde. The DIN 4000-160-1 tabular layout of article characteristics shall apply to screws covered in this standard. The DIN Standards corresponding to the International Standards referred

6、 to in Clause 2 of this document are as follows: ISO 225 DIN EN ISO 225 ISO 724 DIN ISO 724 ISO 898-1 DIN EN ISO 898-1 ISO 965-1 DIN ISO 965-1 ISO 3269 DIN EN ISO 3269 ISO 4042 DIN EN ISO 4042 ISO 4759-1 DIN EN ISO 4759-1 ISO 8992 DIN ISO 8992 ISO 10683 DIN EN ISO 10683 Amendments This standard diff

7、ers from DIN EN ISO 4018:2001-03 as follows: a) normative references are now undated; b) property class 3.6 has been deleted from Table 3; c) the standard has been editorially revised and normative references have been updated; d) Annex ZA has been deleted. Previous editions DIN 558-1: 1941-01, 1953

8、-08, 1963-03 DIN 558 Supplement: 1926-10 DIN 558: 1923-02, 1925-04, 1934-07, 1967-12, 1983-12, 1987-09 DIN ISO 4018: 1987-09, 1989-10 DIN EN 24018: 1992-02 DIN EN ISO 4018: 2001-03 2 A comma is used as the decimal marker. DIN EN ISO 4018:2011-07 National Annex NA (informative) Bibliography DIN 4000-

9、160, Tabular layout of product properties Part 160: Fasteners with external thread DIN EN ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions DIN EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs

10、with specified property classes Coarse thread and fine pitch thread DIN EN ISO 3269, Fasteners Acceptance inspection DIN EN ISO 4042, Fasteners Electroplated coatings DIN EN ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C DIN EN ISO 10683, Fastene

11、rs Non-electrolytically applied zinc flake coatings DIN ISO 724, ISO general purpose metric screw threads Basic dimensions DIN ISO 965-1, ISO general purpose metric screw threads Tolerances Part 1: Principles and basic data DIN ISO 8992, Fasteners General requirements for bolts, screws, studs and nu

12、ts 3 DIN EN ISO 4018:2011-07 This page is intentionally blank 4 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 4018 April 2011 ICS 21.060.10 Supersedes EN ISO 4018:2000English Version Hexagon head screws Product grade C (ISO 4018:2011) Vis tte hexagonale entirement filetes Grade C (ISO 401

13、8:2011) Sechskantschrauben mit Gewinde bis Kopf Produktklasse C (ISO 4018:2011) This European Standard was approved by CEN on 31 January 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a nat

14、ional standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A ve

15、rsion in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus,

16、 Czech Republic, Denmark, Estonia,Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT E

17、UROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 4018:2011: EContents Page Foreword3 Introduction .4 1 Scope .5 2 N

18、ormative references.5 3 Dimensions .6 4 Specifications and reference International Standards .11 2EN ISO 4018:2011 (E) DIN EN ISO 4018:2011-07 5 Designation .11 Bibliography 12 Foreword This document (EN ISO 4018:2011) has been prepared by Technical Committee ISO/TC 2 “ Fasteners“ in collaboration w

19、ith Technical Committee CEN/TC 185 “Fasteners”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2011, and conflicting national standards shall be w

20、ithdrawn at the latest by October 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 4018:2000. Acc

21、ording to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, I

22、taly, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 4018:2011 has been approved by CEN as a EN ISO 4018:2011 without any modification. 3EN ISO 4018:2011 (

23、E) DIN EN ISO 4018:2011-07 Introduction This International Standard belongs to a complete family of product standards developed by ISO on external hexagon drive fasteners. It comprises the following: a) hexagon head bolts (ISO 4014, ISO 4015, ISO 4016 and ISO 8765); b) hexagon head screws (ISO 4017,

24、 ISO 4018 and ISO 8676); c) hexagon nuts (ISO 4032, ISO 4033, ISO 4034, ISO 4035, ISO 4036, ISO 7040, ISO 7041, ISO 7042, ISO 7719, ISO 7720, ISO 8673, ISO 8674, ISO 8675, ISO 10511, ISO 10512 and ISO 10513); d) hexagon bolts with flange (ISO 4162, ISO 15071 and ISO 15072); e) hexagon nuts with flan

25、ge (ISO 4161, ISO 7043, ISO 7044, ISO 10663, ISO 12125, ISO 12126 and ISO 21670). 4EN ISO 4018:2011 (E) DIN EN ISO 4018:2011-07 1 Scope This International Standard specifies the characteristics of hexagon head screws with threads from M5 up to and including M64, of product grade C. NOTE This type of

26、 product is the same as that covered by ISO 4016 with the exception of threading up to head. If, in special cases, specifications other than those listed in this International Standard are required, they can be selected from existing International Standards, for example ISO 724, ISO 888, ISO 898-1,

27、ISO 965-1 and ISO 4759-1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

28、ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions ISO 724, ISO general-purpose metric screw threads Basic dimensions ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classe

29、s Coarse thread and fine pitch thread ISO 965-1, ISO general-purpose metric screw threads Tolerances Part 1: Principles and basic data ISO 3269, Fasteners Acceptance inspection ISO 4042, Fasteners Electroplated coatings ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Produ

30、ct grades A, B and C ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings 5EN ISO 4018:2011 (E) DIN EN ISO 4018:2011-07 3 Dimensions See Figure 1 and Tables 1 and 2. Symbols and descriptions of dimensions are

31、 specified in ISO 225. Dimensions in millimetres a = 15 to 30. e Reference datum for dw. b End without special requirements. f ds pitch diameter. c Incomplete thread u u 2P. g Permissible shape. d Washer face permissible. Figure 1 6EN ISO 4018:2011 (E) DIN EN ISO 4018:2011-07 Table 1 Preferred threa

32、ds Dimensions inmillimetres Thread, dM5 M6 M8 M10 M12 M16 M20 M24 M30 M36 M42 M48 M56 M64 Pa0,8 1 1,25 1,5 1,75 2 2,5 3 3,5 4 4,5 5 5,5 6 max. 2,4 3 4 4,5 5,3 6 7,5 9 10,5 12 13,5 15 16,5 18 amin. 0,8 1 1,25 1,5 1,75 2 2,5 3 3,5 4 4,5 5 5,5 6 cmax. 0,5 0,5 0,6 0,6 0,6 0,8 0,8 0,8 0,8 0,8 1 1 1 1 dam

33、ax. 6 7,2 10,2 12,2 14,7 18,7 24,4 28,4 35,4 42,4 48,6 56,6 67 75 dwmin. 6,74 8,74 11,47 14,47 16,47 22 27,7 33,25 42,75 51,11 59.95 69,45 78,66 88,16 emin. 8,63 10,89 14,2 17,59 19,85 26,17 32,95 39,55 50,85 60,79 71,3 82,6 93,56 104,86nom. 3,5 4 5,3 6,4 7,5 10 12,5 15 18,7 22,5 26 30 35 40 max. 3,

34、875 4,375 5,675 6,85 7,95 10,75 13,4 15,9 19,75 23,55 27,05 31,05 36,25 41,25 kmin. 3,125 3,625 4,925 5,95 7,05 9,25 11,6 14,1 17,65 21,45 24,95 28,95 33,75 38,75 kwbmin. 2,19 2,54 3,45 4,17 4,94 6,48 8,12 9,87 12,36 15,02 17,47 20,27 23,63 27,13 rmin. 0,2 0,25 0,4 0,4 0,6 0,6 0,8 0,8 1 1 1,2 1,6 2

35、2 nom. =max. 8,00 10,00 13,00 16,00 18,00 24,00 30,00 36 46 55,0 65,0 75,0 85,0 95,0 smin. 7,64 9,64 12,57 15,57 17,57 23,16 29,16 35 45 53,8 63,1 73,1 82,8 92,8 lcnom. min. max. 10 9,25 10,75 12 11,1 12,9 16 15,1 16,9 20 18,95 21,05 25 23,95 26,05 30 28,95 31,05 35 33,75 36,25 40 38,75 41,25 45 43,

36、75 46,25 50 48,75 51,25 55 53,5 56,5 60 58,5 61,5 65 63,5 66,5 70 68,5 71,5 80 78,5 81,5 7EN ISO 4018:2011 (E) DIN EN ISO 4018:2011-07 Table 1(continued)Dimensions inmillimetres Thread, dM5 M6 M8 M10 M12 M16 M20 M24 M30 M36 M42 M48 M56 M64 lcnom. min. max. 90 88,25 91,75 100 98,25 101,75110 108,2511

37、1,75120 118,25121,75130 128 132 140 138 142 150 148 152 160 156 164 180 176 184 200 195,4 204,6 220 215,4 224,6 240 235,4 244,6 260 254,8 265,2 280 274,8 285,2 300 294,8 305,2 320 314,3 325,7 340 334,3 345,7 360 354,3 365,7 380 374,3 385,7 400 394,3 405,7 420 413,7 426,3 440 433,7 446,3 460 453,7 46

38、6,3 480 473,7 486,3 500 493,7 506,3 aPis the pitch of the thread. bkw,min=0,7 kmin. cThe range of preferred lengths is between the solid, bold, stepped lines. 8EN ISO 4018:2011 (E) DIN EN ISO 4018:2011-07 Table 2 Non-preferredthreads Dimensions inmillimetres Thread, dM14 M18 M22 M27 M33 M39 M45 M52

39、M60 Pa2 2,5 2,5 3 3,5 4 4,5 5 5,5 max. 6 7,5 7,5 9 10,5 12 13,5 15 16,5 amin. 2 2,5 2,5 3 3,5 4 4,5 5 5,5 cmax. 0,6 0,8 0,8 0,8 0,8 1 1 1 1 damax. 16,7 21,2 26,4 32,4 38,4 45,4 52,6 62,6 71 dwmin. 19,15 24,85 31,35 38 46,55 55,86 64,7 74,2 83,41 emin. 22,78 29,56 37,29 45,2 55,37 66,44 76,95 88,25 9

40、9,21 nom. 8,8 11,5 14 17 21 25 28 33 38 max. 9,25 12,4 14,9 17,9 22,05 26,05 29,05 34,25 39,25 kmin. 8,35 10,6 13,1 16,1 19,95 23,95 26,95 31,75 36,75 kwbmin. 5,85 7,42 9,17 11,27 13,97 16,77 18,87 22,23 25,73 rmin. 0,6 0,6 0,8 1 1 1 1,2 1,6 2 nom. =max. 21,00 27,00 34 41 50 60,0 70,0 80,0 90,0 smin

41、. 20,16 26,16 33 40 49 58,8 68,1 78,1 87,8 lcnom. min. max. 30 28,95 31,05 35 33,75 36,25 40 38,75 41,25 45 43,75 46,25 50 48,75 51,25 55 53,5 56,5 60 58,5 61,5 65 63,5 66,5 70 68,5 71,5 80 78,5 81,5 90 88,25 91,75 100 98,25 101,75110 108,25111,75120 118,25121,75130 128 132 9EN ISO 4018:2011 (E) DIN

42、 EN ISO 4018:2011-07 Table 2(continued)Dimensions inmillimetres Thread, dM14 M18 M22 M27 M33 M39 M45 M52 M60 lcnom. min. max. 140 138 142 150 148 152 160 156 164 180 176 184 200 195,4 204,6 220 215,4 224,6 240 235,4 244,6 260 254,8 265,2 280 274,8 285,2 300 294,8 305,2 320 314,3 325,7 340 334,3 345,

43、7 360 354,3 365,7 380 374,3 385,7 400 394,3 405,7 420 413,7 426,3 440 433,7 446,3 460 453,7 466,3 480 473,7 486,3 500 493,7 506,3 aPis the pitch of the thread. bkw,min=0,7 kmin. cThe range of preferred lengths is between the solid, bold, stepped lines.10EN ISO 4018:2011 (E) DIN EN ISO 4018:2011-07 4

44、 Specifications and reference International Standards See Table 3. Table 3 Specifications and reference International Standards Material Steel General requirements International Standard ISO 8992 Tolerance class 8g Thread International Standard ISO 724, ISO 965-1 Property classad u 39 mm: 4.6, 4.8 d

45、 39 mm: as agreed Mechanical property International Standard d u 39 mm: ISO 898-1 d 39 mm: as agreed Product grade C Tolerance International Standard ISO 4759-1 As processed Finish Coating Requirements for electroplating are specified in ISO 4042. Requirements for non-electrolytically applied zinc f

46、lake coatings are specified in ISO 10683. Additional requirements or other finishes or coatings shall be agreed between the supplier and the purchaser. Acceptability Acceptance inspection is specified in ISO 3269. aOther property classes are specified in ISO 898-1. 5 Designation EXAMPLE A hexagon he

47、ad screw, product grade C, with thread M12, nominal length l = 80 mm and property class 4.6 is designated as follows: Hexagon head screw ISO 4018 - M12 80 - 4.6 11EN ISO 4018:2011 (E) DIN EN ISO 4018:2011-07 Bibliography 1 ISO 888, Bolts, screws and studs Nominal lengths, and thread lengths for gene

48、ral purpose bolts 2 ISO 4014, Hexagon head bolts Product grades A and B 3 ISO 4015, Hexagon head bolts Product grade B Reduced shank (shank diameter approximately equal to pitch diameter) 4 ISO 4016, Hexagon head bolts Product grade C 5 ISO 4017, Hexagon head screws Product grades A and B 6 ISO 4032

49、, Hexagon nuts, style 1 Product grades A and B 7 ISO 4033, Hexagon nuts, style 2 Product grades A and B 8 ISO 4034, Hexagon nuts Product grade C 9 ISO 4035, Hexagon thin nuts (chamfered) Product grades A and B 10 ISO 4036, Hexagon thin nuts (unchamfered) Product grade B 11 ISO 4161, Hexagon nuts with flange Coarse thread 12 ISO 4162, Hexagon flange bolts Small series 13 ISO 7040, Prevailing torque type hexagon nuts (with non-m