DIN EN ISO 4017-2015 Fasteners - Hexagon head screws - Product grades A and B (ISO 4017 2014) German version EN ISO 4017 2014《紧固件 六角头螺钉 产品等级A和B级(ISO 4017-2014) 德文版本EN ISO 4017-2014.pdf

《DIN EN ISO 4017-2015 Fasteners - Hexagon head screws - Product grades A and B (ISO 4017 2014) German version EN ISO 4017 2014《紧固件 六角头螺钉 产品等级A和B级(ISO 4017-2014) 德文版本EN ISO 4017-2014.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 4017-2015 Fasteners - Hexagon head screws - Product grades A and B (ISO 4017 2014) German version EN ISO 4017 2014《紧固件 六角头螺钉 产品等级A和B级(ISO 4017-2014) 德文版本EN ISO 4017-2014.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、May 2015Translation by DIN-Sprachendienst.ICS 21.060.10DDIN EN ISO 4017Fasteners Hexagon head screws Product grades A and B (ISO 4017:2014);English version EN ISO 4017:2014,English translation of DIN EN ISO 4017:2015-05Mechanische Verbindungselemente Sechskantschrauben mit Gewinde bis Kopf Produktkl

2、assen A und B (ISO 4017:2014);Englische Fassung EN ISO 4017:2014,Englische bersetzung von DIN EN ISO 4017:2015-05Fixations Vis tte hexagonale entirement filetes Grades A et B (ISO 4017:2014);Version anglaise EN ISO 4017:2014,Traduction anglaise de DIN EN ISO 4017:2015-05SupersedesDIN EN ISO 4017:201

3、4-10In case of doubt, the German-language original shall be considered authoritative.English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sal

4、e for German Standards (DIN-Normen).!%BI.“2313811www.din.dewww.beuth.deDocument comprises 20 pages04.15 DIN EN ISO 4017:2015-05 2 A comma is used as the decimal marker. National foreword This document (EN ISO 4017:2014) has been prepared by Technical Committee ISO/TC 2 “Fasteners” in col-laboration

5、with Technical Committee CEN/TC 185 “Fasteners” (both secretariats are held by DIN, Germany). The responsible German body involved in its preparation was the DIN-Normenausschuss Mechanische Verbindungselemente (DIN Standards Committee Fasteners), Working Committee NA 067-00-02 AA Verbin-dungselement

6、e mit metrischem Auengewinde. The DIN 4000-160-1 tabular layout of product properties applies to hexagon head screws covered in this standard. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 225 DIN EN ISO 225 ISO 724 DIN ISO 724 ISO 89

7、8-1 DIN EN ISO 898-1 ISO 965-1 DIN ISO 965-1 ISO 3269 DIN EN ISO 3269 ISO 3506-1 DIN EN ISO 3506-1 ISO 4014 DIN EN ISO 4014 ISO 4015 DIN EN 24015 ISO 4016 DIN EN ISO 4016 ISO 4018 DIN EN ISO 4018 ISO 4032 DIN EN ISO 4032 ISO 4033 DIN EN ISO 4033 ISO 4034 DIN EN ISO 4034 ISO 4035 DIN EN ISO 4035 ISO

8、4036 DIN EN ISO 4036 ISO 4042 DIN EN ISO 4042 ISO 4753 DIN EN ISO 4753 ISO 4759-1 DIN EN ISO 4759-1 ISO 6157-1 DIN EN 26157-1 ISO 7040 DIN EN ISO 7040 ISO 7042 DIN EN ISO 7042 ISO 7719 DIN EN ISO 7719 ISO 8673 DIN EN ISO 8673 ISO 8674 DIN EN ISO 8674 ISO 8675 DIN EN ISO 8675 ISO 8676 DIN EN ISO 8676

9、 ISO 8765 DIN EN ISO 8765 ISO 8839 DIN EN 28839 ISO 8992 DIN ISO 8992 ISO 10511 DIN EN ISO 10511 ISO 10512 DIN EN ISO 10512 ISO 10513 DIN EN ISO 10513 ISO 10683 DIN EN ISO 10683 ISO 10684 DIN EN ISO 10684 ISO 21670 DIN EN ISO 21670 The DIN Standards corresponding to the following International Stand

10、ards adopted as European Standards are as follows: ISO 4161 DIN EN 1661 ISO 7043 DIN EN 1663 ISO 7044 DIN EN 1664 ISO 10663 DIN EN 14218 ISO 12125 DIN EN 1666 ISO 12126 DIN EN 1667 DIN EN ISO 4017:2015-05 3 Amendments This standard differs from DIN EN ISO 4017:2011-07 as follows: a) the standard has

11、 been editorially revised and normative references have been updated; b) the values of cminand cmax, which were erroneously interchanged in Table 1 (for threads M8 to M64) and in Table 2 have been corrected; c) the value lmaxfor product grade B at lnom= 110 mm in Table 1 has been changed for threads

12、 M8 to M24 from 111,25 mm to 111,75 mm; d) in Tables 1 and 2, the number of decimal places has been unified; e) in Table 3, column “Finish Coating”, an information about requirements for hot dip galvanized coatings for steel fasteners has been added. Compared with DIN EN ISO 4017:2014-10, the follow

13、ing corrections have been made: a) the dashed lines in Tables 1 and 2 are now correct; in the 2014-10 edition they had been incorrectly represented as solid lines. Previous editions DIN 933-1: 1926-07, 1942-04, 1952-12, 1963-03 DIN 933-2: 1926-07, 1942-04 DIN KrK 144: 1931-02 DIN Kr 553: 1935-09 DIN

14、 933: 1967-12, 1970-12, 1983-12, 1987-09 DIN ISO 4017: 1987-09, 1989-10 DIN EN 24017: 1992-02 DIN EN ISO 4017: 2001-03, 2011-07, 2014-10 DIN EN ISO 4017 Corrigendum 1:2005-03 DIN EN ISO 4017:2015-05 4 National Annex NA (informative) Bibliography DIN 4000-160, Tabular layout of product properties Par

15、t 160: Fasteners with external thread DIN EN 1661, Hexagon nuts with flange DIN EN 1663, Prevailing torque type hexagon nuts with flange (with non-metallic insert) DIN EN 1664, Prevailing torque type All-metal hexagon nuts with flange DIN EN 1666, Prevailing torque type hexagon nuts with flange (wit

16、h non-metallic insert), with metric fine pitch thread DIN EN 1667, Prevailing torque type all hexagon nuts with flange, with metric fine pitch thread DIN EN 14218, Hexagon nuts with flange Fine pitch thread DIN EN 24015, Hexagon head bolts with reduced shank (shank diameter pitch diameter) Product g

17、rade B DIN EN 26157-1, Fasteners Surface discontinuities Bolts, screws and studs subject to general require-ments DIN EN 28839, Mechanical properties of fasteners Nonferrous metal bolts, screws, studs and nuts DIN EN ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimens

18、ions DIN EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and fine pitch thread DIN EN ISO 3269, Fasteners Acceptance inspection DIN EN ISO 3506-1, Mechanical properties of corrosion-re

19、sistant stainless steel fasteners Part 1: Bolts, screws and studs DIN EN ISO 4014, Hexagon head bolts Product grades A and B DIN EN ISO 4016, Hexagon head bolts Product grade C DIN EN ISO 4018, Hexagon head screws Product grade C DIN EN ISO 4032, Hexagon regular nuts (style 1) Product grades A and B

20、 DIN EN ISO 4033, Hexagon high nuts (style 2) Product grades A and B DIN EN ISO 4034, Hexagon regular nuts (style 1) Product grade C DIN EN ISO 4035, Hexagon thin nuts chamfered (style 0) Product grades A and B DIN EN ISO 4036, Hexagon thin nuts unchamfered (style 0) Product grade B DIN EN ISO 4042,

21、 Fasteners Electroplated coatings DIN EN ISO 4017:2015-05 5 DIN EN ISO 4753, Fasteners Ends of parts with external ISO metric thread DIN EN ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C DIN EN ISO 7040, Prevailing torque type hexagon regular nut

22、s (with non-metallic insert) Property classes 5, 8 and 10 DIN EN ISO 7042, Prevailing torque type all-metal hexagon high nuts Property classes 5, 8, 10 and 12 DIN EN ISO 7719, Prevailing torque type all-metal hexagon regular nuts Property classes 5, 8 and 10 DIN EN ISO 8673, Hexagon regular nuts (st

23、yle 1) with metric fine pitch thread Product grades A and B DIN EN ISO 8674, Hexagon high nuts (style 2) with metric fine pitch thread Product grades A and B DIN EN ISO 8675, Hexagon thin nuts chamfered (style 0) with metric fine pitch thread Product grades A and B DIN EN ISO 8676, Hexagon head scre

24、ws with metric fine pitch thread Product grades A and B DIN EN ISO 8765, Hexagon head bolts with metric fine pitch thread Product grades A and B DIN EN ISO 10511, Prevailing torque type hexagon thin nuts (with non-metallic insert) DIN EN ISO 10512, Prevailing torque type hexagon regular nuts (with n

25、on-metallic insert) with metric fine pitch thread Property classes 6, 8 and 10 DIN EN ISO 10513, Prevailing torque type all-metal hexagon high nuts with metric fine pitch thread Property classes 8, 10 and 12 DIN EN ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings DIN EN ISO 1068

26、4, Fasteners Hot dip galvanized coatings DIN EN ISO 21670, Fasteners Hexagon weld nuts with flange DIN ISO 724, ISO general purpose metric screw threads Basic dimensions DIN ISO 965-1, ISO general purpose metric screw threads Tolerances Part 1: Principles and basic data DIN ISO 8992, Fasteners Gener

27、al requirements for bolts, screws, studs and nuts DIN EN ISO 4017:2015-05 6 This page is intentionally blank EN ISO 4017June 2014 ICS 21.060.10 Supersedes EN ISO 4017:2011English Version Fasteners - Hexagon head screws - Product grades A and B (ISO 4017:2014) Fixations - Vis tte hexagonale entiremen

28、t filetes - Grades A et B (ISO 4017:2014)Mechanische Verbindungselemente - Sechskantschraubenmit Gewinde bis Kopf - Produktklassen A und B(ISO 4017:2014)This European Standard was approved by CEN on 10 May 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulat

29、e the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Stan

30、dard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the nat

31、ional standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Sl

32、ovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 4017:2014 EEUROPEAN COMMITTEE FOR STA

33、NDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMContents Page Foreword . 3 Introduction . 4 1 Scope . 5 2 Normative references. 5 3 Dimensions . 6 4 Specifications and reference International Standards . 12 5 Designation . 12 Bib

34、liography 13 2DIN EN ISO 4017:2015-05 EN ISO 4017:2014 (E) ForewordThis document (EN ISO 4017:2014) has been prepared by Technical Committee ISO/TC 2 “Fasteners” in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN. This European Standard shall be

35、given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2014, and conflicting national standards shall be withdrawn at the latest by December 2014. Attention is drawn to the possibility that some of the elements of this documen

36、t may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 4017:2011. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bou

37、nd to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portuga

38、l, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 4017:2014 has been approved by CEN as EN ISO 4017:2014 without any modification. 3DIN EN ISO 4017:2015-05EN ISO 4017:2014 (E)IntroductionThis International Standard belongs t

39、o a complete family of product standards developed by ISO on external hexagon drive fasteners. It comprises the following:a) hexagon head bolts (ISO 4014, ISO 4015, ISO 4016 and ISO 8765);b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676);c) hexagon nuts (ISO 4032, ISO 4033, ISO 4034, ISO 4035

40、, ISO 4036, ISO 7040, ISO 7041, ISO 7042, ISO 7719, ISO 7720, ISO 8673, ISO 8674, ISO 8675, ISO 10511, ISO 10512 and ISO 10513);d) hexagon bolts with flange (ISO 4162, ISO 15071 and ISO 15072);e) hexagon nuts with flange (ISO 4161, ISO 7043, ISO 7044, ISO 10663, ISO 12125, ISO 12126 and ISO 21670).4

41、DIN EN ISO 4017:2015-05 EN ISO 4017:2014 (E) 1 ScopeThis International Standard specifies the characteristics of hexagon head screws with threads from M1,6 up to and including M64, of product grade A for threads M1,6 to M24 and nominal lengths up to and including 10 d or 150 mm, whichever is the sho

42、rter, and product grade B for threads over M24 or nominal lengths over 10 d or 150 mm, whichever is the shorter.NOTE This type of product is the same as that covered by ISO 4014 with the exception of threading up to head and nominal lengths up to and including 200 mm as preferred lengths.If, in spec

43、ial cases, specifications other than those listed in this International Standard are required, they can be selected from existing International Standards, for example ISO 724, ISO 888, ISO 898-1, ISO 965-1, ISO 3506-1, ISO 4753 and ISO 4759-1.2 Normative referencesThe following documents, in whole o

44、r in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 225, Fasteners Bolts, screws, studs and

45、 nuts Symbols and descriptions of dimensionsISO 724, ISO general-purpose metric screw threads Basic dimensionsISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and fine pitch threadISO 965-

46、1, ISO general purpose metric screw threads Tolerances Part 1: Principles and basic dataISO 3269, Fasteners Acceptance inspectionISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studsISO 3508, Thread run-outs for fasteners with thread in ac

47、cordance with ISO 261 and ISO 262ISO 4042, Fasteners Electroplated coatingsISO 4753, Fasteners Ends of parts with external ISO metric threadISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and CISO 6157-1, Fasteners Surface discontinuities Part 1: Bolts,

48、 screws and studs for general requirementsISO 8839, Mechanical properties of fasteners Bolts, screws, studs and nuts made of non-ferrous metalsISO 8992, Fasteners General requirements for bolts, screws, studs and nutsISO 10683, Fasteners Non-electrolytically applied zinc flake coatingsISO 10684, Fas

49、teners Hot dip galvanized coatings5DIN EN ISO 4017:2015-05EN ISO 4017:2014 (E)3 DimensionsSee Figure 1 and Tables 1 and 2.Symbols and descriptions of dimensions are specified in ISO 225.Dimensions in millimetresKeya = 15 to 30bPoint shall be chamfered or for threads M4 may be as-rolled (sheared end) in accordance with ISO 4753.cIncomplete thread u 2P.dR