DIN EN ISO 13565-1-1998 Geometrical Product Specifications (GPS) - Surface texture Profile method - Surfaces having stratified functional properties - Part 1 Filtering and general .pdf

《DIN EN ISO 13565-1-1998 Geometrical Product Specifications (GPS) - Surface texture Profile method - Surfaces having stratified functional properties - Part 1 Filtering and general .pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 13565-1-1998 Geometrical Product Specifications (GPS) - Surface texture Profile method - Surfaces having stratified functional properties - Part 1 Filtering and general .pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、DEUTSCHE NORM Amil 1998 GPS - Surface texture: Profile method Surfaces having stratified functional properties Part 1 : Filtering and general measurement conditions English version of DIN EN IS0 13565-1 (IS0 13565-1 : 1996) DIN EN IS0 13565-1 ICs 17.040.20 Descriptors: GPS, surface texture, filterin

2、g. This standard, together with DIN EN IS0 13565-2, April 1998 edition, super- sedes DIN 4776 and Suppl 1 to DIN 4776, May 1990 editions. Geometrische Produktspezifikationen (GPS) - Oberflchen- beschaffenheit: Tastschnittverfahren - Oberflchen mit plateauartigen funktionsrelevanten Eigenschaften - T

3、eil 1 : Filterung und allgemeine Mebedingungen (IS0 13565-1 : 1996) European Standard EN IS0 13565-1 : 1997 has the status of a DIN Standard. A comma is used as the decimal marker. National foreword This standard has been published in accordance with a decision taken by CEN/TC 290 to adopt, without

4、alteration, International Standard IS0 13565-1 as a European Standard. The responsible German body involved in its preparation was the Normenausschu Technische Grundlagen (Fundamentals in Technology Standards Committee), Technical Committee Geometrische Produktspezifi- kation und -Prfung. DIN EN IS0

5、 3274 and DIN EN IS0 11562 are the DIN Standards corresponding to International Standards IS0 3274 and IS0 11562, respectively, referred to in clause 2 of the EN. Amendments DIN 4776 and Suppl 1 to DIN 4776, May 1990 editions, have been superseded by the specifications of EN IS0 13565-1 and EN IS0 1

6、3565-2, which are identical to IS0 13565-1 and IS0 13565-2, respectively. Previous editions DIN 4776: 1990-05; SUPPI 1 to DIN 4776: 1990-05. National Annex NA Standards referred to (and not included in Normative references and Annex ZA) DIN EN IS0 3274 DIN EN IS0 11 562 GPS - Surface texture: Profil

7、e method - Nominal characteristics of contact (stylus) instruments (IS0 3274 : 1996) GPS - Surface texture: Profile method - Metrological characteristics of phase correct filters (IS0 11 562 : 1996) EN comprises 7 pages. No pari of this standard may be reproduced without the prior permission of Ref.

8、 No. DIN EN IS0 13565-1 : 1998-0 V Deutsches Institut fr Nonung e. V., Berlin. Luth Verlag GmbH, D-10772 Berlin, has the exclusive right of sale for German Standards (DIN-Normen). English price group 08 Sales No. 11 08 09.98 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IS0 13565-1 December 1

9、997 ICs 17.040.20 Descriptors: GPS, surface texture, filtering. English version Geometrical Product Specifications (GPS) Surfaces having stratified functional properties Part 1 : Filtering and general measurement conditions Surface texture: Profile method (IS0 13565-1 : 1996) Spcification gomtrique

10、des Geometrische Produktspezifikationen produits (GPS) - tat de surface: Mthode du profil - Surfaces ayant des proprits fonctionnelles diff- rentes suivant les niveaux - Partie 1 : Filtrage et conditions gnrales de allgemeine Mebedingungen (GPS) - Oberflchenbeschaffenheit: Tastschnittverfahren - Obe

11、rflchen mit plateauartigen funktionsrelevanten Eigenschaften - Teil1 : Filterung und mesurage (IS0 13565-1 : 1996) (IS0 13565-1 : 1996) This European Standard was approved by CEN on 1997-1 1-02. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions f

12、or giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national stand- ards may be obtained on application to the Central Secretariat or to any CEN member. The European Standards exist in three offici

13、al versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Be

14、lgium, the Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung C

15、entral Secretariat: rue de Stassart 36, 8-1050 Brussels O 1997. CEN - All rights of exploitation in any form and by any means reserved worldwide for CEN national members. Ref. No. EN IS0 13565-1 : 1997 E Page 2 EN IS0 13565-1 : 1997 Foreword International Standard IS0 13565-1 : 1996 Geometrical Prod

16、uct Specifications (GPS) - Surface texture: Profile method - Surfaces having stratified functional properties - Part 1 : Filtering and general measurement con- ditions, which was prepared by ISO/TC 57 Metrology and properties of surfaces of the International Organization for Standardization, has bee

17、n adopted by Technical Committee CEN/TC 290 Dimensional and geometrical prod- uct specification and verification, the Secretariat of which is held by DIN, as a European Standard. This European Standard shall be given the status of a national standard, either by publication of an identical text or by

18、 endorsement, and conflicting national standards withdrawn, by June 1998 at the latest. In accordance with the CENKENELEC Internal Regulations, the national standards organizations of the follow- ing countries are bound to implement this European Standard: Austria, Belgium, the Czech Republic, Denma

19、rk, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom. Endorsement notice The text of the International Standard IS0 13565-1 : 1996 was approved by CEN as a European Standard without any modifi

20、cation. NOTE: Normative references to international publications are listed in Annex ZA (normative). Introduction This part of IS0 13565 is a Geometrical Product Specification (GPS) standard and is to be regarded as a General GfS standard (see ISO/TR 14638). It influences chain links 2 and 3 of the

21、chain of standards for roughness profile. For more detailed information of the relation of this standard to other standards and the GPS matrix model, see annex A. The roughness profile generated using the filter defined in IS0 11 562 suffers some undesirable distortions, when the measured surface co

22、nsists of relatively deep valleys beneath a more finely finished plateau with minimal waviness. This type of surface is very common, for example in cylinder liners for internal combustion engines. This part of IS0 13565 provides a method of greatly reducing these distortions, thus enabling the param

23、eters defined in IS0 13565-2 and IS0 13565-3 to be used for evaluating the above mentioned type of surface, with minimal influence from these distortions. Page 3 EN IS0 13565-1 : 1997 1 Scope This part of IS0 13565 describes a filtering method for use with surfaces that have deep valleys below a mor

24、e finely finished plateau with a relatively small amount of waviness. The reference line resulting from filtering according to IS0 11562 for such surfaces is undesirably influenced by the presence of the valleys. The filtering approach described in this standard suppresses the valley influence on th

25、e reference line such that a more satisfactory reference line is generated. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of IS0 13565. At the time of publication, the editions indicated were valid. All sta

26、ndards are subject to revision, and parties to agreements based on this part of IS0 13565 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. IS0 327

27、4: 1996, Geometrical Product Specifications (GPSI - Surface texture: Profile method - Nominal characteristics of contact (stylus) instruments. IS0 4287: 1 996, Geometrical Product Specifications (GPSI - Surface texture: Profile method - Terms, definitions and surface texture parameters. IS0 1 1562:1

28、996, Geometrical Product Specifications (GPS) - Surface texture: Profile method - Metrological characteristics of phase correct filters. 3 Definitions For the purposes of this part of IS0 13565, the definitions given in IS0 3274 and IS0 4287 apply. Page 4 EN IS0 13565-1 : 1997 25 4 Reference guide 1

29、2,5 To measure profiles in accordance with this part of IS0 13565, a measuring system which incorporates an external reference is recommended. In case of arbitration the use of such a system is obligatory. 5 Traversing direction The traversing direction shall be perpendicular to the direction of lay

30、 unless otherwise indicated. 6 Filtering process to determine the roughness profile The filtering process is carried out in several stages giving the modified profiles, sections of which are illustrated in figure la) to d). The first mean line is determined by a preliminary filtering of the primary

31、profile with the phase correct filter in accordance with IS0 11562 using a cut-off wavelength Ac in accordance with clause 7 and corresponding measuring conditions in accordance with table 1 of IS0 3274:1996. All valley portions which lie below this mean line (shown hatched in figure la) are removed

32、. In these places the primary profile is replaced by the curve of the mean line. The same filter is used again on this profile with the valleys suppressed. The second mean line thus obtained (see figure 1 b) is the reference line relative to which the assessment of profile parameters is performed. T

33、his reference line is tranferred to the original primary profile (see figure IC) and the roughness profile according to this part of IS0 13565 is obtained from the difference between the primary profile and the reference line (see figure Id). 7 Selection of the cut-off wavelength Ac and the evaluati

34、on length In The measurements shall preferably be carried out using a cut-off wavelength of Ac = 0,8 mm. In justified exceptional cases, Ac = 2,5 mm may be selected and this shall be stated in the specification and test results. Table 1 provides the relationship between cut-off wavelength Ac and the

35、 evaluation length In Table 1 - Relationship between the cut-off wavelength Ac and the evaluation length In Dimensions in millimetres Page 5 EN IS0 13565-1 : 1997 I a) Unfiltered primary profile (valleys shown hatched) b) Unfiltered primary profile after suppression of valleys c) Position of the ref

36、erence line in the primary profile Figure 1 - Filtering process Page 6 EN IS0 13565-1 : 1997 Size I I Annex A (informative) I I Relation to GPS matrix model For full details about the GPS matrix model see ISOTTR 14638. A.l Information about this part of IS0 13565 and its use This part of IS0 13565 d

37、escribes a filtering method for use with surfaces that have deep valleys below a more finely finished plateau with a relatively small amount of waviness. The roughness profile generated using the filter defined in IS0 1 1562 suffers some undesirable distortions, when measuring this type of surface,

38、which is very common. This method serves to reduce these distortions, thus enabling the parameters defined in IS0 13565-2 and IS0 13565-3 to be used for evaluating the above-mentioned type of surface, with minimal influence from these distortions. A.2 Position in the GPS matrix model This part of IS

39、0 13565 is a General GPS standard, which influences the chain links 2 and 3 of the chain of standards for roughness profile in the General GPS matrix, as graphically illustrated in figure A.1. Fundamental GPS standards 7 Global GPS standards I General GPC matrix Chain link number 111213141516 Radius

40、 Form of surface deisendent on datum Orientation Location Circular run-out Total run-out Figure A.l A.3 Related standards The related International Standards are those of the chains of standards indicated in figure A.l. Page 7 EN IS0 13565-1 : 1997 Annex B (informative) Bibliography I 1 IS0 13565-2:

41、 1996, Geometrical Product Specifications (GPS) - Surface texture: Profile method; Surfaces having stratified functional properties - Part 2: Height characterization using the linear material ratio curve. 21 I SO 13565-3:- having stratified functional properties - Part 3: Height characterization usi

42、ng the material probability curve. ISO/TR 14638:1995, Geometrical Product Specifications (GPSI - Masterplan VIM - International vocabulary of basic and general terms in metrology. BIPM, IEC, IFCC, KO, IUPAC, IUPAP, OIML, 2nd edition, 1993. Geometrical Product Specifications (GPSI - Surface texture:

43、Profile method; Surfaces 131 141 1) To be published. Annex ZA (normative) Normative references to international publications with their relevant European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references cit

44、ed at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. Publication Year Title - EN Year IS0 1 1562 1996 Geometrical product specifications (GPS) EN IS0 11 562 1997 - Surface texture: Profile method - Metrological characteristics of phase correct filters