DIN EN ISO 1207-2011 Slotted cheese head screws - Product grade A (ISO 1207 2011) German version EN ISO 1207 2011《开槽圆柱头螺钉 产品等级A (ISO 1207-2011) 德文版本EN ISO 1207-2011》.pdf
《DIN EN ISO 1207-2011 Slotted cheese head screws - Product grade A (ISO 1207 2011) German version EN ISO 1207 2011《开槽圆柱头螺钉 产品等级A (ISO 1207-2011) 德文版本EN ISO 1207-2011》.pdf》由会员分享,可在线阅读,更多相关《DIN EN ISO 1207-2011 Slotted cheese head screws - Product grade A (ISO 1207 2011) German version EN ISO 1207 2011《开槽圆柱头螺钉 产品等级A (ISO 1207-2011) 德文版本EN ISO 1207-2011》.pdf(12页珍藏版)》请在麦多课文档分享上搜索。
1、October 2011 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS
2、 21.060.10!$u%6“1820219www.din.deDDIN EN ISO 1207Slotted cheese head screws Product grade A (ISO 1207:2011)English translation of DIN EN ISO 1207:2011-10Zylinderschrauben mit Schlitz Produktklasse A (ISO 1207:2011)Englische bersetzung von DIN EN ISO 1207:2011-10Vis mtaux tte cylindrique fendue Grade
3、 A (ISO 1207:2011)Traduction anglaise de DIN EN ISO 1207:2011-10SupersedesDIN EN ISO 1207:1994-10www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.1209.11DIN EN ISO 1207:2011-10 A comma is used as the decimal marker. National forewor
4、d This standard has been prepared by Technical Committee ISO/TC 2 “Fasteners” in collaboration with Technical Committee CEN/TC 185 “Fasteners” (both secretariats are held by DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Mechanische Verbindungselemente
5、 (Fasteners Standards Committee), Working Committee NA 067-00-05 AA Kleinschrauben und gewindeformende Schrauben. The DIN 4000-160 tabular layout of article characteristics shall apply to screws covered in this standard. The DIN Standards corresponding to the International Standards referred to in t
6、his document are as follows: ISO 225 DIN EN ISO 225 ISO 261 DIN ISO 261 ISO 898-1 DIN EN ISO 898-1 ISO 965-2 DIN ISO 965-2 ISO 965-3 DIN ISO 965-3 ISO 3269 DIN EN ISO 3269 ISO 3506-1 DIN EN ISO 3506-1 ISO 4042 DIN EN ISO 4042 ISO 4753 DIN EN ISO 4753 ISO 4759-1 DIN EN ISO 4759-1 ISO 6157-1 DIN EN 26
7、157-1 ISO 6157-3 DIN EN 26157-3 ISO 8839 DIN EN 28839 ISO 8992 DIN ISO 8992 ISO 10683 DIN EN ISO 10683 ISO 16048 DIN EN ISO 16048 Amendments This standard differs from DIN EN ISO 1207:1994-10 as follows: a) normative references have been revised; b) in Table 2, specifications relating to the surface
8、 have been rendered more precise and requirements for non-electrolytically applied zinc flake coatings and passivation have been added; c) the standard has been editorially revised. 2 DIN EN ISO 1207:2011-10 Previous editions DIN 83-1: 1924-03 DIN 83-2: 1924-03 DIN 83: 1938-11 DIN 84-1: 1921-08, 192
9、4-03, 1937-01 DIN 84-2: 1921-08, 1924-03, 1943-04 DIN 84: 1942x-10, 1952-12, 1964-04, 1968-07, 1970-10, 1988-10, 1990-08 DIN EN ISO 1207: 1994-10 3 DIN EN ISO 1207:2011-10 4 National Annex NA (informative) Bibliography DIN 4000-160, Tabular layout of product properties Part 160: Fasteners with exter
10、nal thread DIN EN 26157-1, Fasteners Surface discontinuities Bolts, screws and studs subject to general requirements DIN EN 26157-3, Fasteners Surface discontinuities Bolts, screws and studs subject to special requirements DIN EN 28839, Mechanical properties of fasteners Nonferrous metal bolts, scre
11、ws, studs and nuts DIN EN ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions DIN EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and fine pitch thr
12、ead DIN EN ISO 3269, Fasteners Acceptance inspection DIN EN ISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs DIN EN ISO 4042, Fasteners Electroplated coatings DIN EN ISO 4753, Fasteners Ends of parts with external ISO metric thread DI
13、N EN ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C DIN EN ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings DIN EN ISO 16048, Passivation of corrosion-resistant stainless-steel fasteners DIN ISO 261, ISO general purpose metri
14、c screw threads General plan DIN ISO 965-2, ISO general purpose metric screw threads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads Medium quality DIN ISO 965-3, ISO general purpose metric screw threads Tolerances Part 3: Deviations for constructional thre
15、ads DIN ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 1207 August 2011 ICS 21.060.10 Supersedes EN ISO 1207:1994English Version Slotted cheese head screws - Product grade A (ISO 1207:2011) Vis mtaux tte cylindrique
16、 fendue - Grade A(ISO 1207:2011) Zylinderschrauben mit Schlitz - Produktklasse A(ISO 1207:2011) This European Standard was approved by CEN on 1 July 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the st
17、atus of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French,
18、German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cro
19、atia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARD
20、IZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 1207:2011: EContents Page Foreword 3EN ISO 1207:201
21、1 (E) DIN EN ISO 1207:2011-10 21 Scope4 2 Normative references4 3 Dimensions 5 4 Specifications and reference International Standards 7 5 Designation 7 Bibliography8 Foreword This document (EN ISO 1207:2011) has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in collaboration with Technica
22、l Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2012, and conflicting national standards shall be withdrawn at
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DINENISO12072011SLOTTEDCHEESEHEADSCREWSPRODUCTGRADEAISO12072011GERMANVERSIONENISO12072011 开槽 圆柱 螺钉 产品
链接地址:http://www.mydoc123.com/p-679090.html