DIN EN 16307-5-2013 Industrial trucks - Safety requirements and verification - Part 5 Supplementary requirements for pedestrian-propelled trucks German version EN 16307-5 2013《工业卡车.pdf

《DIN EN 16307-5-2013 Industrial trucks - Safety requirements and verification - Part 5 Supplementary requirements for pedestrian-propelled trucks German version EN 16307-5 2013《工业卡车.pdf》由会员分享，可在线阅读，更多相关《DIN EN 16307-5-2013 Industrial trucks - Safety requirements and verification - Part 5 Supplementary requirements for pedestrian-propelled trucks German version EN 16307-5 2013《工业卡车.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、June 2013 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 53

2、.060!%B|“2023189www.din.deDDIN EN 16307-5Industrial trucks Safety requirements and verification Part 5: Supplementary requirements for pedestrian-propelled trucks;English version EN 16307-5:2013,English translation of DIN EN 16307-5:2013-06Flurfrderzeuge Sicherheitstechnische Anforderungen und Verif

3、izierung Teil 5: Zustzliche Anforderungen fr mitgngerbetriebene Flurfrderzeuge;Englische Fassung EN 16307-5:2013,Englische bersetzung von DIN EN 16307-5:2013-06Chariots de manutention Exigences de scurit et vrification Partie 5: Exigences supplmentaires pour les chariots conducteur accompagnant;Vers

4、ion anglaise EN 16307-5:2013,Traduction anglaise de DIN EN 16307-5:2013-06www.beuth.deDocument comprises 13 pagesIn case of doubt, the German-language original shall be considered authoritative.06.13DIN EN 16307-5:2013-06 2 A comma is used as the decimal marker. National foreword This standard inclu

5、des safety requirements. This document (EN 16307-5:2013) has been prepared by Technical Committee CEN/TC 150 “Industrial trucks Safety” (Secretariat: BSI, United Kingdom). The responsible German body involved in its preparation was the Normenausschuss Maschinenbau (Mechanical Engineering Standards C

6、ommittee), Working Committee NA 060-22-42 AA Sicherheit von Flurfrderzeugen of Section Frdertechnik. Representatives of manufacturers and users of industrial trucks, and of the employers,liability insurance associations contributed to this standard. This standard contains specifications meeting the

7、essential requirements set out in Annex I of the “Machinery Directive”, Directive 2006/42/EC, and which apply to machines that are either first placed on the market or commissioned within the EEA. This standard serves to facilitate proof of compliance with the essential requirements of that directiv

8、e. The European Standards referred to in Clause 2 and in the Bibliography of the EN have been published as the corresponding DIN EN or DIN EN ISO Standards with the same number. Where the International Standards referred to are not also DIN ISO Standards with the same number, there are no national s

9、tandards available. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16307-5 March 2013 ICS 53.060 English Version Industrial trucks - Safety requirements and verification - Part 5: Supplementary requirements for pedestrian-propelled trucks Chariots de manutention - Exigences de scurit et vrific

10、ation - Partie 5: Exigences supplmentaires pour les chariots conducteur accompagnant Flurfrderzeuge - Sicherheitstechnische Anforderungen und Verifizierung - Teil 5: Zustzliche Anforderungen fr mitgngerbetriebene Flurfrderzeuge This European Standard was approved by CEN on 10 February 2013. CEN memb

11、ers are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on applicati

12、on to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Managem

13、ent Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

14、Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Br

15、ussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16307-5:2013: EEN 16307-5:2013 (E) 2 Contents Page Foreword 3 0 Introduction 4 0.1 General 4 0.2 Assessment of hazards .4 1 Scope 5 2 Normative references 5 3 Terms and de

16、finitions .5 4 Safety requirements and/or protective measures 6 4.1 General 6 4.2 Protection against crushing, shearing and trapping .6 4.2.1 General 6 4.2.2 Pedestrian-propelled trucks with mast .6 4.3 Electrical requirements .6 4.4 Electromagnetic compatibility (EMC) 6 4.5 Operation in potentially

17、 explosive atmospheres 6 5 Verification of safety requirements and/or protective measures .6 6 Information for use 6 6.1 Instruction handbook(s) - Operation of truck .6 6.2 Marking Information plates 7 Annex A (informative) List of significant hazards 8 Annex ZA (informative) Relationship between th

18、is European Standard and the Essential Requirements of EC Directive 2006/42/EC . 10 Bibliography . 11 DIN EN 16307-5:2013-06 EN 16307-5:2013 (E) 3 Foreword This document (EN 16307-5:2013) has been prepared by Technical Committee CEN/TC 150 “Industrial trucks - Safety”, the secretariat of which is he

19、ld by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2013,and conflicting national standards shall be withdrawn at the latest by September 2013. Attention is drawn to the possibili

20、ty that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Assoc

21、iation, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. EN 16307, Industrial trucks Safety requirements and verification, consists of the following parts: Part 1: Supplementary requir

22、ements for self-propelled industrial trucks, other than driverless trucks, variable-reach trucks and burden-carrier trucks Part 2: Supplementary requirements for self-propelled variable-reach trucks Part 3: Supplementary requirements for trucks with elevating operator position and trucks specificall

23、y designed to travel with elevated loads Part 4: Supplementary requirements for driverless industrial trucks and their systems Part 5: Supplementary requirements for pedestrian-propelled trucks Part 6: Supplementary requirements for burden and personnel carriers This document is based on ISO/TS 3691

24、-7, Industrial trucks Safety requirements and verification Part 7: Regional requirements for countries within the European Community, and is limited to pedestrian-propelled industrial trucks. This document is to be used with EN ISO 3691-5, Industrial trucks Safety requirements and verification Part

25、5: Pedestrian-propelled trucks (ISO 3691-5). According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Forme

26、r Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 16307-5:2013-06 EN 16307-5:2013 (E)

27、 4 0 Introduction 0.1 General This document is a type-C standard as stated in EN ISO 12100. The machines concerned and the extent to which hazards, hazardous situations or hazardous events are covered are indicated in the Scope of this document. When requirements of this type-C standard are differen

28、t from those which are stated in type-A or type-B standards, the requirements of this type-C standard take precedence over the requirements of the other standards for machines that have been designed and built according to the requirements of this type-C standard. The EN 16307 series of standards co

29、vers safety requirements and their verification for industrial trucks, as defined in ISO 5053, that are not covered exhaustively by the EN ISO 3691 series. 0.2 Assessment of hazards The product needs to be designed in such a way that it is fit for its purpose or function and can be adjusted and main

30、tained without putting persons at risk when used under the conditions foreseen by the manufacturer. In order to properly design a product and to cover all specific safety requirements, the manufacturer will have to identify the hazards that apply to his product and carry out a risk assessment. The m

31、anufacturer will then need to design and construct the product taking this assessment into account. The aim of this procedure is to eliminate the risk of accidents throughout the expected lifetime of the machinery, including the phases of assembling and dismantling where risks of accidents could als

32、o arise from foreseeable abnormal situations. In selecting the most appropriate methods, the manufacturer will need to apply the following principles, in the order given here: a) eliminate or reduce risks as far as possible by design (inherently safe machinery design and construction); b) take the n

33、ecessary protective measures in relation to risks that cannot be eliminated by design; c) inform users of any shortcoming of the protective measures adopted; d) indicate whether any particular training is required; e) specify any need to provide personal protection equipment; f) refer to the appropr

34、iate users document for proper operating instructions. Industrial trucks need to be designed to prevent foreseeable misuse wherever possible if such misuse would engender risk. In other cases, the instructions will need to draw the users attention to ways shown by experience in which the machinery o

35、ught not be used. This part of EN 16307 does not repeat all the technical rules which are state-of-the art and which are applicable to the material used to construct the industrial truck. Reference will also need to be made to EN ISO 12100. DIN EN 16307-5:2013-06 EN 16307-5:2013 (E) 5 1 Scope This E

36、uropean Standard gives requirements for the types of industrial trucks specified in the scope of EN ISO 3691-5. This European Standard is intended to be used in conjunction with EN ISO 3691-5. These requirements are supplementary to those stated in EN ISO 3691-5 with the addition of the following ha

37、zards: Electromagnetic compatibility (EMC); when operating in potentially explosive atmospheres. This European standard partially replaces the following requirements of EN ISO 3691-5: Electrical requirements. This European standard defines supplementary requirements to EN ISO 3691-5: protection agai

38、nst crushing, shearing and trapping; information for use (instruction handbook and marking). Annex A (informative) contains the list of significant hazards covered by this standard. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and a

39、re indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 953, Safety of machinery Guards General requirements for the design and construction of fixed and m

40、ovable guards EN 1175-1, Safety of industrial trucks Electrical requirements Part 1: General requirements for battery powered trucks EN 1755, Safety of industrial trucks Operation in potentially explosive atmospheres Use in flammable gas, vapour, mist and dust EN 12895, Industrial trucks Electromagn

41、etic compatibility EN ISO 3691-5:2009, Industrial trucks Safety requirements and verification Part 5: Pedestrian-propelled trucks (ISO 3691-5:2009) ISO 5053:1987, Powered industrial trucks Terminology 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 5

42、053:1987 and EN ISO 3691-5:2009 apply. DIN EN 16307-5:2013-06 EN 16307-5:2013 (E) 6 4 Safety requirements and/or protective measures 4.1 General The following applies to the pedestrian-propelled trucks, dealt with in EN ISO 3691-5. These are additional to the requirements of EN ISO 3691-5 and, in ce

43、rtain instances, replace them. 4.2 Protection against crushing, shearing and trapping 4.2.1 General The requirements of EN ISO 3691-5:2009, 5.8 shall apply with the following additions: Where fixed and/or removable guard systems are needed, the requirements of EN 953 shall be met. When a fixed guard

44、 is removed, its fixing system shall remain on the guard or truck. This requirement applies to any fixed guards that are liable to be removed by the user with a risk of loss of the fixings, e.g. fixed guards that are liable to be removed during routine maintenance or setting operations carried out a

45、t the place of use. 4.2.2 Pedestrian-propelled trucks with mast The mast shall be guarded on the side facing the operating controls, e.g. by a transparent cover. The guard shall, as a minimum, cover the whole width of the hazardous zone and the full length of the non-elevated mast, or up to 2,2 m fr

46、om the ground, whichever is less. 4.3 Electrical requirements Subclause 5.11.2, first paragraph of EN ISO 3691-5:2009 is replaced with the following: Electrical systems and equipment shall be in accordance with EN 1175-1. 4.4 Electromagnetic compatibility (EMC) The trucks EMC shall comply with EN 12

47、895. 4.5 Operation in potentially explosive atmospheres Trucks operating in potentially explosive atmospheres shall comply with EN 1755. 5 Verification of safety requirements and/or protective measures The requirements specified in Clause 4 shall be verified in accordance with the reference standard

48、s. 6 Information for use 6.1 Instruction handbook(s) - Operation of truck The requirements of EN ISO 3691-5:2009, 7.2.3 shall apply with the following addition: The instruction handbook(s) shall include, as applicable, the following: information about specific protective devices (e.g. protective scr

49、een) and their use. DIN EN 16307-5:2013-06 EN 16307-5:2013 (E) 7 6.2 Marking Information plates The requirements of EN ISO 3691-5:2009, 7.3.1 shall apply with the following modifications. Replace EN ISO 3691-5:2009, 7.3.1.1 b) with the following: designation of the machinery, designation of series or type and the mandatory marking1). 1) For industrial trucks intended to be put on the market in the EEA, CE marking as defined in the applicable European directive(s), e.g. Machinery, Out