DIN EN 13523-2-2014 Coil coated metals - Test methods - Part 2 Gloss German version EN 13523-2 2014《涂覆金属卷材 试验方法 第2部分 光泽度 EN 13523-2 2014的德文版本》.pdf
《DIN EN 13523-2-2014 Coil coated metals - Test methods - Part 2 Gloss German version EN 13523-2 2014《涂覆金属卷材 试验方法 第2部分 光泽度 EN 13523-2 2014的德文版本》.pdf》由会员分享,可在线阅读,更多相关《DIN EN 13523-2-2014 Coil coated metals - Test methods - Part 2 Gloss German version EN 13523-2 2014《涂覆金属卷材 试验方法 第2部分 光泽度 EN 13523-2 2014的德文版本》.pdf(11页珍藏版)》请在麦多课文档分享上搜索。
1、August 2014 Translation by DIN-Sprachendienst.English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS
2、25.220.60!%:;4“2232417www.din.deDDIN EN 13523-2Coil coated metals Test methods Part 2: Gloss;English version EN 13523-2:2014,English translation of DIN EN 13523-2:2014-08Bandbeschichtete Metalle Prfverfahren Teil 2: Glanz;Englische Fassung EN 13523-2:2014,Englische bersetzung von DIN EN 13523-2:2014
3、-08Tles prlaques Mthodes dessai Partie 2: Brillant;Version anglaise EN 13523-2:2014,Traduction anglaise de DIN EN 13523-2:2014-08SupersedesDIN EN 13523-2:2001-12www.beuth.deDocument comprises 11 pagesIn case of doubt, the German-language original shall be considered authoritative.07.14DIN EN 13523-2
4、:2014-08 2 A comma is used as the decimal marker. National foreword This document (EN 13523-2:2014) has been prepared by Technical Committee CEN/TC 139 “Paints and varnishes”, (Secretariat: DIN, Germany), Working Group WG 9 “Testing of coil coated metals” (Secretariat: DIN, Germany). The responsible
5、 German body involved in its preparation was the Normenausschuss Beschichtungsstoffe und Beschichtungen (DIN Standards Committee Coatings and Coating Materials), Working Committee NA 002-00-07 AA Allgemeine Prfverfahren fr Beschichtungsstoffe und Beschichtungen. Amendments This standard differs from
6、 DIN EN 13523-2:2001-12 as follows: a) the text of this standard has been brought in line with the revised version of EN ISO 2813, i.e. the result of the measurement is expressed in gloss units (GU); b) the definition of specular gloss has been deleted; c) for calibration of the glossmeter, referenc
7、e to EN ISO 2813 has been added; d) an information concerning the conditioning of the specimen has been added; e) the procedure has been amended so that measurements can be taken in the rolling direction or perpendicular to the rolling direction, which has to be stated in the test report; f) the sel
8、ection of the measuring geometry has been brought in line with the revised version of EN ISO 2813; g) for precision data, reference to EN ISO 2813 has been added. Previous editions DIN EN 13523-2: 2001-12 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13523-2 June 2014 ICS 25.220.60 Supersedes
9、 EN 13523-2:2001English Version Coil coated metals - Test methods - Part 2: Gloss Tles prlaques - Mthodes dessai - Partie 2: Brillant Bandbeschichtete Metalle - Prfverfahren - Teil 2: Glanz This European Standard was approved by CEN on 7 May 2014. CEN members are bound to comply with the CEN/CENELEC
10、 Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or t
11、o any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the offici
12、al versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, N
13、orway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of ex
14、ploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13523-2:2014 EEN 13523-2:2014 (E) 2 Contents Page Foreword 3 Introduction .5 1 Scope 6 2 Normative references 6 3 Terms and definitions .6 4 Principle 6 5 Apparatus .6 6 Sampling .6 7 Test panels .7 8 Pr
15、ocedure .7 8.1 Selection of the measuring geometry7 8.2 Calibration 7 8.3 Measurement 7 9 Expression of results 7 10 Precision .7 11 Test report 7 Bibliography 9 DIN EN 13523-2:2014-08 EN 13523-2:2014 (E) 3 Foreword This document (EN 13523-2:2014) has been prepared by Technical Committee CEN/TC 139
16、“Paints and varnishes”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2014, and conflicting national standards shall be withdrawn at the latest
17、by December 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13523-2:2001. The main technical changes
18、 are: a) the text was aligned with the revision of EN ISO 2813, i.e. the result of the measurement is expressed in gloss units (GU); b) the definition for specular gloss was deleted; c) for calibration of the glossmeter, a reference to EN ISO 2813 was added; d) a remark on preconditioning was added;
19、 e) the procedure was amended so that measurements can be taken in the rolling direction or perpendicular to the rolling direction, which has to be stated in the test report; f) the selection of the measuring geometry was aligned with the revision of EN ISO 2813. g) for precision data, a reference t
20、o EN ISO 2813 was added. EN 13523, Coil coated metals Test methods, consists of the following parts: Part 0: General introduction Part 1: Film thickness Part 2: Gloss Part 3: Colour difference Instrumental comparison Part 4: Pencil hardness Part 5: Resistance to rapid deformation (impact test) Part
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DINEN1352322014COILCOATEDMETALSTESTMETHODSPART2GLOSSGERMANVERSIONEN1352322014 金属 卷材 试验 方法 部分 光泽 EN1352322014

链接地址:http://www.mydoc123.com/p-666251.html