BS ISO 96-1-2016 Textile machinery and accessories Rings and travellers for ring spinning and ring twisting frames Flange rings T and SF and their travellers《纺织机械和附件 环锭细纱机和环锭捻线机用钢领.pdf

《BS ISO 96-1-2016 Textile machinery and accessories Rings and travellers for ring spinning and ring twisting frames Flange rings T and SF and their travellers《纺织机械和附件 环锭细纱机和环锭捻线机用钢领.pdf》由会员分享，可在线阅读，更多相关《BS ISO 96-1-2016 Textile machinery and accessories Rings and travellers for ring spinning and ring twisting frames Flange rings T and SF and their travellers《纺织机械和附件 环锭细纱机和环锭捻线机用钢领.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO 96-1:2016T e x t i l e m a c h i n e r y a n d accessories Rings and travellers for ring spinning and ring twisting framesPart 1: Flange rings T and SF and their travellersBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 96-1:2016 BRITISH STANDARDNationa

2、l forewordThis British Standard is the UK implementation of ISO 96-1:2016. It supersedes BS ISO 96-1:2009 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee TCI/33, Textile machinery.A list of organizations represented on this committee can be obtained on

3、 request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 88139 8 ICS 59.120.10 Compliance with a B

4、ritish Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 November 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 96-1:2016 ISO 2016Textile machiner

5、y and accessories Rings and travellers for ring spinning and ring twisting frames Part 1: Flange rings T and SF and their travellersMatriel pour lindustrie textile Anneaux et curseurs pour machines filer et retordre Partie 1: Anneaux T et SF et leurs curseursINTERNATIONAL STANDARDISO96-1Third editio

6、n2016-11-15Reference numberISO 96-1:2016(E)BS ISO 96-1:2016ISO 96-1:2016(E)ii ISO 2016 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or

7、 by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 C

8、P 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 96-1:2016ISO 96-1:2016(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Principal dimensions of T- and SF-rings. 15 Travellers . 36 Designation of traveller

9、s 4 ISO 2016 All rights reserved iiiContents PageBS ISO 96-1:2016ISO 96-1:2016(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through

10、ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates

11、 closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval crite

12、ria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of

13、patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name u

14、sed in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) pr

15、inciples in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.The committee responsible for this document is ISO/TC 72, Textile machinery and accessories, Subcommittee SC 1, Spinning preparatory, spinning, twisting and winding machinery and accessories.This t

16、hird edition cancels and replaces the second edition (ISO 96-1:2009), of which it constitutes a minor revision with the following changes:a) full height h1in Figure 1 given;b) full height h2in Figure 2 given;c) value of flange width b2in Table 1 changed;d) new value of 8 for height h1and h2in Table

17、1 inserted;e) flange width b1in Figure 3 removed and adapted to Figure 4;f) Clause 6 editorially revised.A list of all parts in the ISO 96 series can be found on the ISO website.iv ISO 2016 All rights reservedBS ISO 96-1:2016INTERNATIONAL STANDARD ISO 96-1:2016(E)Textile machinery and accessories Ri

18、ngs and travellers for ring spinning and ring twisting frames Part 1: Flange rings T and SF and their travellers1 ScopeThis document specifies the principal dimensions of T- and SF-rings, and the mass and tolerance on the mass, of the appropriate travellers for flange rings employed on ring spinning

19、 and ring twisting machines. It also specifies the method of designation of the travellers.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited

20、 applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 3, Preferred numbers Series of preferred numbers3 Terms and definitionsNo terms and definitions are listed in this document.ISO and IEC maintain terminological databases for use in

21、standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at https:/www.iso.org/obp/4 Principal dimensions of T- and SF-ringsThe principal dimensions of T- and SF-rings are illustrated in Figures 1 and 2, and specif

22、ied in Table 1.Figure 1 Example of a T-ring ISO 2016 All rights reserved 1BS ISO 96-1:2016ISO 96-1:2016(E)Figure 2 Example of an SF-ringTable 1 Ring dimensionsDimensions in millimetresT-Ring SF-RingInside diameter dHeight h1Fitting diameter d1Flange width b1Height h2Fitting diameter d2Flange width b

23、2nominal tolerancea+0,15 0nominal tolerancea+0,2 0,136384042454881000,200,2(50)5154(55)576063(65)7075810d + 700,252,6b3,2c4d81012d + 1200,252,83,8aThe tolerance refers to the diameter d1, respectively d2, excluding any ovality.bThe flange width b1= 2,6 mm was designated previously as ring flange No.

24、 1/2.cThe flange width b1= 3,2 mm was designated previously as ring flange No. 1.dThe flange width b1= 4 mm was designated previously as ring flange No. 2.2 ISO 2016 All rights reservedBS ISO 96-1:2016ISO 96-1:2016(E)5 Travellers5.1 Examples of travellers appropriate for T- and SF-rings are shown in

25、 Figures 3 and 4.Figure 3 Example of a traveller for a T-ring in the running positionFigure 4 Example of a traveller for an SF-ring in the running position5.2 The values for traveller mass are given in Table 2.Traveller mass is taken from the R20 series of preferred numbers in accordance with ISO 3.

26、 The range of traveller mass comprises values from 4 to 900 inclusive.The traveller mass represents the nominal mass, in grams, of 1 000 travellers of the same type. The tolerance on the nominal mass for 1 000 travellers of the same type is 3 %. ISO 2016 All rights reserved 3BS ISO 96-1:2016ISO 96-1

27、:2016(E)Table 2 Traveller massMass of traveller (grams per 1 000 travellers)4 25 1604,5 28 1805 31,5 2005,6 35,5 2246,3 40 2507,1 45 2808 50 3159 56 35510 63 40011,2 71 45012,5 80 50014 90 56016 100 63018 112 71020 125 80022,4 140 9006 Designation of travellersThe designation on the packing of trave

28、llers for the T- and SF-ring includes the following information:a) the denotation “Traveller” (optional);b) a reference to this document, i.e. ISO 96-1 (optional);c) the symbol “T” or “SF” (optional);d) the flange width, b1, in millimetres, of the appropriate ring (optional);e) the manufacturers des

29、ignation for the traveller style (e.g. “C”, “EL”);f) the wire section symbol (if applicable), e.g. “f ”, “r ” (“f” = flat, “r” = round);g) the traveller mass (see Table 2);h) the traveller material or traveller name if it is other than steel (where this information is omitted, it is assumed that the

30、 traveller material is steel);i) the surface finish (optional);j) the appearance (optional).4 ISO 2016 All rights reservedBS ISO 96-1:2016BS ISO 96-1:2016ISO 96-1:2016(E) ISO 2016 All rights reservedICS 59.120.10Price based on 4 pagesThis page deliberately left blankBSI is the national body responsi

31、ble for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together busine

32、ss, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of

33、all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Know

34、ledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Developmen

35、t Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the inter

36、national standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or pub

37、licly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use onl

38、y. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard copy format: A British Standard pu

39、rchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you

40、 can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For fur

41、ther information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch wit

42、h standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of y

43、our standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wi

44、sh. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit

45、 your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Group Headquarters389 Chiswick High Road London W4 4AL UKBSI Back Cover.indd 1 27/01/2016 14:20