BS ISO 4548-6-2012 Methods of test for full-flow lubricating oil filters for internal combustion engines Static burst pressure test《内燃机全流式机油滤清器试验方法 静压耐破度试验》.pdf

《BS ISO 4548-6-2012 Methods of test for full-flow lubricating oil filters for internal combustion engines Static burst pressure test《内燃机全流式机油滤清器试验方法 静压耐破度试验》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 4548-6-2012 Methods of test for full-flow lubricating oil filters for internal combustion engines Static burst pressure test《内燃机全流式机油滤清器试验方法 静压耐破度试验》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 4548-6:2012Methods of test for full-flow lubricating oil filters forinternal combustion enginesPart 6: Static burst pressure testBS ISO 4548-6:2012 BRITISH STANDARDNationa

2、l forewordThis British Standard is the UK implementation of ISO 4548-6:2012. Itsupersedes BS7403-6:1991 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MCE/21/5, Filters for lubricating oil.A list of organizations represented on this committee can beobt

3、ained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012. Published by BSI StandardsLimited 2012ISBN 978 0 580 68597 2ICS 27.020Compliance with a

4、British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 October 2012.Amendments issued since publicationDate Text affectedBS ISO 4548-6:2012 ISO 2012Methods of test for full-flow lubrica

5、ting oil filters for internal combustion engines Part 6: Static burst pressure testMthodes dessai des filtres huile de lubrification passage intgral pour moteurs combustion interne Partie 6: Essai de pression dclatement statiqueINTERNATIONAL STANDARDISO4548-6Second edition2012-09-15Reference numberI

6、SO 4548-6:2012(E)BS ISO 4548-6:2012ISO 4548-6:2012(E)ii ISO 2012 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2012All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photoco

7、pying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS

8、 ISO 4548-6:2012ISO 4548-6:2012(E) ISO 2012 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 14 Test rig . 15 Test liquid 16 Preparation and test procedure . 17 Report of test results 2BS ISO 4548-6:2012ISO 4548-6:2012(E)Forewo

9、rdISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technica

10、l committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of ele

11、ctrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the

12、member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identi

13、fying any or all such patent rights.ISO 4548-6 was prepared by Technical Committee ISO/TC 70, Internal combustion engines, Subcommittee SC 7, Tests for lubricating oil filters.This second edition cancels and replaces the first edition (ISO 4548-6:1985, including ISO 4548-6:1985/Cor 1:1990), which ha

14、s been technically revised.ISO 4548 consists of the following parts, under the general title Methods of test for full-flow lubricating oil filters for internal combustion engines: Part 1: Differential pressure/flow characteristics Part 2: Element by-pass valve characteristics Part 3: Resistance to h

15、igh differential pressure and to elevated temperature Part 4: Initial particle retention efficiency, life and cumulative efficiency (gravimetric method) Part 5: Method of test for cold start simulation and hydraulic pulse durability Part 6: Static burst pressure test Part 7: Vibration fatigue test P

16、art 9: Inlet and outlet anti-drain valve tests Part 11: Self-cleaning filters Part 12: Filtration efficiency using particle counting, and contaminant retention capacity Part 13: Static burst pressure test for composite pressure vessel materials Part 15: Vibration fatigue test with composite material

17、siv ISO 2012 All rights reservedBS ISO 4548-6:2012ISO 4548-6:2012(E)IntroductionThis International Standard establishes standard test procedures for measuring the performance of full-flow lubricating oil filters for internal combustion engines. It has been prepared in separate parts, each part relat

18、ing to a particular performance characteristic. ISO 2012 All rights reserved vBS ISO 4548-6:2012BS ISO 4548-6:2012Methods of test for full-flow lubricating oil filters for internal combustion engines Part 6: Static burst pressure test1 ScopeThis part of ISO 4548 specifies a method of testing full-fl

19、ow lubricating oil filters for internal combustion engines to determine their ability to withstand a static pressure objective and to determine their burst pressure and the failure mode concerned.It does not apply to filters for use in aeronautical applications or plastic components.2 Normative refe

20、rencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 4548-1, Methods of test for full-flow lu

21、bricating oil filters for internal combustion engines Part 1: Differential pressure/flow characteristics3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 4548-1 apply.4 Test rigHydraulic hand pump or other appropriate technology, with high-pressure tubi

22、ng and valves, pressure gauge with measuring range of 0 kPa to 3000 kPa or higher (see 6.6). A transparent safety shield shall be used.5 Test liquidISO Grade 22 oil with a 96 VI (or SAE 5 W oil) at ambient temperature shall be used.6 Preparation and test procedure6.1 Assemble the complete filter usi

23、ng the recommended tightening torque. If a tolerance is given, apply the minimum tightening torque.The filter to adaptor connection shall be equivalent to the production mounting conditions.6.2 Connect the pump to the inlet of the filter or adaptor, and the outlet of the filter or adaptor to an open

24、 valve. The outlet of the valve should be the highest point of the system.6.3 Introduce oil into the system by operating the pump until oil is seen to emerge from the outlet of the valve. This indicates that all the air has been excluded from the system.6.4 Close the valve and position the safety sh

25、ield between observer and filter.INTERNATIONAL STANDARD ISO 4548-6:2012(E) ISO 2012 All rights reserved 1BS ISO 4548-6:2012ISO 4548-6:2012(E)6.5 Raise the pressure gradually to 200 kPa, maintain for about 1 min, and check the filter and all fittings for leaks.NOTE If appropriate burst pressure is kn

26、own, the first pressure increment can be 50 % of the known value. This shortens the test time for high pressure filters without a loss in data quality.6.6 Now raise the pressure at a controlled pressure ramp up to approximately 345 kPa to 690 kPa per minute and maintain for approximately 15 s and ch

27、eck filter for leaks or distortion. Continue until a specified (see 7g)pressure objective is reached as determine by the customer, or otherwise failure occurs.6.7 Relieve the pressure to zero. Check the filter for permanent distortion and tightening torque.Take note of the remaining tightening torqu

28、e and if loosening has occurred, restore the initial value.6.8 Gradually apply pressure again until the previous pressure is reached, then proceed gradually in increments of approximately 345 kPa to 690 kPa and maintain for approximately 15 s until ultimate failure occurs.6.9 Examine the filter for

29、details of the failure mode.7 Report of test resultsThe test report shall indicate at least the following:a) a reference to this part of ISO 4548, i.e. ISO 4548-6;b) test establishment;c) filter type (manufacturer model No. and batch No.);d) date of test;e) a description of the filter, whether it is

30、 new or used (in the latter case, approximate period of service);f) the torque applied initially (see 6.1);g) the specified pressure objective as determined by the customer and whether reached (see 6.6);h) the remaining tightening torque (see 6.7);i) visible permanent distortion (see 6.7);j) the bur

31、st pressure (see 6.8);k) the mode of failure and its location.2 ISO 2012 All rights reservedBS ISO 4548-6:2012ISO 4548-6:2012(E)124356Figure 1 Static burst pressure test standKey1 Oil sump2 Pump3 Pressure sensor4 Filter under test5 Valve6 Pressure regulating valve ISO 2012 All rights reserved 3BS IS

32、O 4548-6:2012ISO 4548-6:2012(E) ISO 2012 All rights reservedICS 27.020Price based on 3 pagesThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on

33、 standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20

34、 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be

35、grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44

36、 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy v

37、ersions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international st

38、andards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax:

39、 +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email:

40、 Information regarding online access to British Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the pr

41、operty of and copyrighted by BSI, or some person or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act

42、1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: