BS ISO 3320-2013 Fluid power systems and components Cylinder bores and piston rod diameters and area ratios Metric series《流体动力系统和组件 缸内径及活塞杆外径和面积比 米制系列》.pdf

《BS ISO 3320-2013 Fluid power systems and components Cylinder bores and piston rod diameters and area ratios Metric series《流体动力系统和组件 缸内径及活塞杆外径和面积比 米制系列》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 3320-2013 Fluid power systems and components Cylinder bores and piston rod diameters and area ratios Metric series《流体动力系统和组件 缸内径及活塞杆外径和面积比 米制系列》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 3320:2013Fluid power systems andcomponents Cylinder boresand piston rod diameters andarea ratios Metric seriesBS ISO 3320:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 3320:2013. Itsupersedes BS ISO 7181:1991 which is with

2、drawn.The UK participation in its preparation was entrusted to TechnicalCommittee MCE/18/-/3, Cylinders.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are r

3、esponsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 80094 8ICS 23.100.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStanda

4、rds Policy and Strategy Committee on 31 December 2013.Amendments issued since publicationDate Text affectedBS ISO 3320:2013 ISO 2013Fluid power systems and components Cylinder bores and piston rod diameters and area ratios Metric seriesTransmissions et composants hydrauliques et pneumatiques Alsages

5、 des vrins et diamtres des tiges de piston et rapports de surface Srie mtriqueINTERNATIONAL STANDARDISO3320Third edition2013-12-01Reference numberISO 3320:2013(E)BS ISO 3320:2013ISO 3320:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved. Unless otherwise

6、specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below

7、or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 3320:2013ISO 3320:2013(E) ISO 2013 All rights reserved iiiContents PageForeword ivI

8、ntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 14 Symbols and units . 15 Dimensions . 26 Area ratios . 37 Identification statement (reference to this International Standard) 3BS ISO 3320:2013ISO 3320:2013(E)ForewordISO (the International Organization for Standardization) i

9、s a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represe

10、nted on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop

11、 this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IE

12、C Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the

13、 development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning o

14、f ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 131, Flui

15、d power systems, Subcommittee SC 3, Cylinders.This third edition of ISO 3320 cancels and replaces the second edition (ISO 3320:1987) and the second edition of ISO 7181:1991, which have been combined and technically revised.iv ISO 2013 All rights reservedBS ISO 3320:2013ISO 3320:2013(E)IntroductionIn

16、 fluid power systems, power is transmitted and controlled through a liquid (for hydraulics) or a gas (for pneumatics) under pressure within an enclosed circuit.One component of such systems is the fluid power cylinder. This is a device that converts power into linear mechanical force and motion. It

17、consists of a movable element, i.e. a piston and piston rod, operating within a cylindrical bore. ISO 2013 All rights reserved vBS ISO 3320:2013BS ISO 3320:2013Fluid power systems and components Cylinder bores and piston rod diameters and area ratios Metric series1 ScopeThis International Standard e

18、stablishes a metric series of cylinder bore and piston rod diameters for hydraulic and pneumatic cylinders, and specifies for each pair of diameters a corresponding standard ratio between the useful areas.This International Standard applies only to the dimensional criteria of products manufactured i

19、n conformity with this International Standard; it does not apply to their functional characteristics.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited

20、 applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3, Preferred numbers Series of preferred numbersISO 5598, Fluid power systems and components VocabularyISO 6099, Fluid power systems and components Cylinders Identification code fo

21、r mounting dimensions and mounting types3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 5598 apply.4 Symbols and unitsSymbols and units used in this International Standard are shown in Table 1.Table 1 Symbols and unitsSymbol Designation UnitALaCylinde

22、r bore diameter mmMMaPiston rod diameter mmA=4AL12pi Area cylinder cap side cm2A=4AL MM222pi()Area cylinder rod side cm2=AA12Area ratio -aLetter codes are in accordance with ISO 6099.INTERNATIONAL STANDARD ISO 3320:2013(E) ISO 2013 All rights reserved 1BS ISO 3320:2013ISO 3320:2013(E)5 Dimensions5.1

23、 The cylinder bore diameter (AL) is shown in Figure 1 and values are specified in Table 2.5.2 The cylinder rod diameter (MM) is shown in Figure 1 and values are specified in Table 3.Figure 1 Identification of bore and rod dimensionsTable 2 Cylinder bore diameters (AL)Dimensions in millimetresAL8 10

24、12 16 20 25 32 40 50 60 63 80 (90) 100(110) 125 (140) 160 (180) 200 (220) 250 (280) 320 (360) 400 (450) 500NOTE 1 An extension upwards of the diameter ranges can be made using the series of preferred numbers given in ISO 3 (R10 for diameters up to bore diameter 100 mm and R20 for bore diameters larg

25、er than 100 mm).NOTE 2 Values in parentheses are non-preferred values and should be used for special applications only.Table 3 Piston rod diameters (MM)Dimensions in millimetresMM4 5 6 8 10 12 14 16 18 20 22 25 28 (30)32 36 40 45 50 56 (60) 63 70 80 90 100 110 (120)125 140 160 180 200 220 250 280 32

26、0 360 400 450 - -NOTE 1 An extension upwards of the diameter ranges can be made using the series of preferred numbers R20 given in ISO 3.NOTE 2 Values in parentheses are non-preferred values and should be used for special applications only.2 ISO 2013 All rights reservedBS ISO 3320:2013ISO 3320:2013(

27、E)6 Area ratios6.1 For each pair of diameters of bore and piston rod, there is a corresponding ratio between the useful areas.6.2 Ratios approximately equal to one of the following preferred numbers are shown in Table 4:1,06 1,12 1,25 1,33 1,4 1,6 2 2,5 56.3 Moreover, for each pair of diameters of b

28、ore (AL) and piston rod (MM), Table 4 gives calculated values of A1and A2and their corresponding effective value .7 Identification statement (reference to this International Standard)It is recommended to manufacturers who have chosen to conform to this International Standard that the following state

29、ment be used in test reports, catalogues, and sales literature:“Cylinder bores, piston rod diameters and ratios selected in accordance with ISO 3320, Fluid power systems and components Cylinder bores and piston rod diameters and area ratios Metric series.” ISO 2013 All rights reserved 3BS ISO 3320:2

30、013ISO 3320:2013(E)Table4 Bore and pistonrod area ratiosDiameters in millimetres, areas in square centimetres AL253240506380(90)100(110)125(140)160(180)200(220)250(280)320(360)400(450)500A14,918,0412,619,631,250,363,678,595,012315420125431438049161680410181257159019631,06MMA284,411,11107,261,111011,

31、81,071218,51,061629,21,072047,11,072259,81,062573,61,072888,91,07321151,07361441,07401881,07452391,07502951,07563561,07634601,07705771,07807541,07909541,0710011781,0711014951,0612518411,071,12MMA2104,121,19126,911,161211,41,101617,61,112028,01,112545,41,112857,51,113270,51,113684,91,12401101,1145138

32、1,12501811,11562301,11632831,11703421,11804411,11905521,121007261,11110923 1,1012511341,1114014361,1116017621,111,25MMA2123,781,30146,501,241810,01,252215,81,242825,01,253640,11,254051,11,254562,61,255075,41,265698,11,25631231,25701631,24802041,25902511,251003021,261103961,241254931,251406501,241608

33、171,2518010021,2520012761,2522015831,241,33MMA2123,781,30166,031,33209,421,332514,71,333024,11,294037,71,334547,71,335058,91,335670,41,356094,41,30701151,33801511,33901911,331002361,331102851,331253681,331404621,331606031,331807631,332009421,3322012101,3125014731,331,4MMA2143,371,46185,501,46228,771

34、,432813,51,463621,01,484534,41,465044,01,455653,91,466363,91,497084,21,46801041,48901371,461001761,451102191,431252571,481403371,461604151,481805501,462007041,45220877 1,4325011001,4528013481,461,6MMA2162,901,69204,901,64257,661,643211,61,694018,61,685030,61,645639,01,636347,41,667056,51,688072,51,6

35、99090,31,701001231,641101591,601251911,641402261,681602901,691803611,702004901,642206381,602507661,642809751,6332011591,692MMA2182,362,08224,241,90286,411,96369,52,084515,32,045625,61,966332,41,967040,11,968044,82,129059,12,0810075,42,041101061,901251321,931401601,961601792,121802362,082003022,04220

36、4241,902505271,932806411,963207862,023609462,082,5MMA2201,772,78253,132,57324,522,7840 7,12,85011,52,706319,12,637025,12,538028,32,789031,43,0310044,22,7811058,92,6112578,32,571401012,531601132,781801263,032001772,782202362,612503132,572804022,533204522,783605732,784007072,785MMA2221,114,43281,884,2

37、7362,395,2645 3,75,26566,54,767011,84,278013,44,769014,95,2610016,55,7611027,74,4312531,24,9314047,14,2716053,44,7618059,75,2620066,05,762201114,432501254,932801884,273202144,763602395,264003344,764503735,26NOTEValues in parentheses are non-preferred values and should be used for special application

38、s only.4 ISO 2013 All rights reservedBS ISO 3320:2013BS ISO 3320:2013ISO 3320:2013(E) ISO 2013 All rights reservedICS 23.100.20Price based on 4 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, informa

39、tion and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government

40、, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all

41、 sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying stan

42、dardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard co

43、pies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and ad

44、opted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format,

45、by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, plea

46、se visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .Revisi

47、onsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre

48、.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed

49、 such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained fro