BS ISO 15644-2002 Road construction and maintenance equipment - Chippings spreaders - Terminology and commercial specifications《道路建设和维修设备 碎石摊铺机 术语和商业规范》.pdf

《BS ISO 15644-2002 Road construction and maintenance equipment - Chippings spreaders - Terminology and commercial specifications《道路建设和维修设备 碎石摊铺机 术语和商业规范》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 15644-2002 Road construction and maintenance equipment - Chippings spreaders - Terminology and commercial specifications《道路建设和维修设备 碎石摊铺机 术语和商业规范》.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 15644:2002 Road construction and maintenance equipment Chippings spreaders Terminology and commercial specifications ICS 91.220 BS ISO 15644:2002 This British Standard, having been prepared under the direction of the Building and Civil Engineering Sector Policy and Strategy C

2、ommittee, was published under the authority of the Standards Policy and S t r a t e g y C o m m i t t e e o n 9 August 2002 BSI 9 August 2002 ISBN 0 580 40205 3 National foreword This British Standard reproduces verbatim ISO 15644:2002 and implements it as the UK national standard. The UK participat

3、ion in its preparation was entrusted to Technical Committee B/513, Construction equipment and plant, and site safety, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which imple

4、ment international publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purpor

5、t to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee

6、any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii to v, a

7、 blank page, pages 1 to 21, and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsINTERNATIONAL STANDARD ISO 15644 First edition 2002-05-01 Reference number ISO 15644:2002(E) Road con

8、struction and maintenance equipment Chippings spreaders Terminology and commercial specifications quipement pour la construction et lentretien des routes Gravillonneuses Terminologie et spcifications commercialesBSISO15644:2002ISO :44651(2002)E ii ISO 2002 Ar llithgr seresvde FDP dicslaimre This FDP

9、 fam elitnoc yt deddebme niayfep.seca In roccatiw ecnadA hycilop gnisnecil sebod, thf sim eliarp eb ytnieiv ro dewb detu sllah ton eb tidesselnu de tt ehyfepseca hwich rae meil era deddebct desneo tsni dnalat no delmoc ehtupre epfrromign tide ehti.gn In odaolnwding htis life, rapticca setpe trehiet

10、neh serilibisnopty fo ton fnirisebodA gnign ilop gnisnecilcy. TI ehSO tneCraceS lrteraiat catpecon s illibayti in ihts aera. ebodA si t armedarak fo dAS ebotsysme Inroctarop.de teDailfo s tfos ehtware prtcudos t desuo crtaet ehFDP si ff eb nac elit ni dnuoG ehlarene Info talerive to tf eh;eli teh PD

11、F-rctaeirap nomateers weer tpof dezimior rptnii.gn vErec yaeeb sah ert nakt neo rusnet etah tf ehi elis tiusbaf elob esu ry ISO merebm seidob. In the kilnuley evtne ttah a borpmel talerign to ti f si,dnuo saelpfni eorm teh tneCS laretercratai ta thserdda es igvne olebw. ISO 2002 Ar llieser sthgrvsse

12、lnU .de torehceps esiwfi,dei rap ont iht fos bupliactim noarper eb yro decudo tuzilina ni dey form b roy nasnaem y, tcelernahcem ro cinoicla, inclidung tohppocoying m dnaicrfomli, tiwtuoh permini noiss wrtif gnirmo ietI rehSO ta tserdda eheb slow or SIsO memreb ydob in toc ehtnury fo tr ehtseuqeer.

13、ISO copyrithg fofiec tsop esaCael 65 G 1121-HCeneva 02 Te.l + 22 14 10 947 11 Fax + 14 47 2290 9 74 E-liam copyrightsio.ch Web wwwsi.oc.h Prni detni Sztiwerldna BSISO15644:2002iiISO 46512002:4)E( ISO 2002 r llAithgs reservde iii Contents Page 1 Scope . 1 2 Normative reference . 1 3 Terms and definit

14、ions 1 4 Description of chippings spreader operation 3 4.1 Extraction or distribution of chippings from the dumper body bottom 3 4.2 Adjustment of chippings flow . 4 4.3 Adjustment of spreading width 4 4.4 Automatic control by vehicle speed . 4 4.5 Diffuser 4 5 Commercial specifications 4 5.1 Transp

15、orted chippings spreader 4 5.2 Self-propelled chippings spreader . 5 5.3 Chippings spreader pushed by tipper truck . 6 BSISO15644:2002iiiISO :44651(2002)E vi ISO 2002 Ar llithgr seresvde Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards

16、 bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organiza

17、tions, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in t

18、he ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that

19、 some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO15644 was prepared by Technical Committee ISO/TC195, Building construction machinery and equipment. BSI

20、SO15644:2002ivISO 46512002:4)E( ISO 2002 r llAithgs reservde v Introduction This International Standard deals with chippings spreaders used in road construction and surface coating. A chippings spreader is a machine used to spread a layer of chippings on the pavement at a predetermined rate. This In

21、ternational Standard describes the performance characteristics and methods of operation of chippings spreaders and their components. It also provides their definitions and technical characteristics. It includes figures explaining the principles of machine operation and showing the main dimensions re

22、lated to the machines performance. BSISO15644:2002vANRETNIITOTS LANDNADRA ISO 46512002:4)E( ISO 2002 r llAithgs reservde 1 Road construction and maintenance equipment Chippings spreaders Terminology and commercial specifications 1 Scope This International Standard establishes the terminology and det

23、ermines the type of technical and commercial specifications for chippings spreaders. This International Standard is applicable to chippings spreaders intended for road construction and surface coating. 2 Normative reference The following normative document contains provisions which, through referenc

24、e in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, this publication do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most

25、 recent edition of the normative document indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. EN 13020, Road-surface treatment machines Safety requirements 3 T

26、erms and definitions For the purposes of this International Standard, the following terms and definitions apply. 3.1 chippings spreader machine used to spread a layer of chippings on the pavement at a pre-determined rate NOTE A chippings spreader may be defined by its operating principle. Three type

27、s of chippings spreaders may be identified: transported, self-propelled and pushed by tipper truck. 3.2 transported chippings spreader machine equipped with chippings spreading device mounted on the rear of a truck or semi-trailer NOTE The chippings spreading device can be provided with rollers deli

28、very, see Figure 2 a) or spreading, see Figure 3 a). Chippings may be distributed also from the dumping body bottom by gravity Figure 3 b). 3.3 self-propelled chippings spreader self-propelled machine provided with delivery roller cf. Figure 2 a) BSISO15644:20021ISO :44651(2002)E 2 ISO 2002 Ar llith

29、gr seresvde 3.4 chippings spreader pushed by tipper truck machine equipped with its own travelling axle and attached to the rear axle of the pushing tipper truck NOTE Delivery roller of the spreader is driven from its travelling axle. 3.5 transport vehicle truck or tractor semi-trailer unit which ca

30、rries all the components and provides movement of the chippings spreader during spreading and road transfers 3.6 dumping body bin in form of a box for storage of chippings during operation and transport NOTE The dumping body supplies the chippings spreading device with chippings. It may be equipped

31、with either a scraper shield or conveyor (see Figure 1). 3.7 partial partition of dumping body division wall added in order to improve the distribution of loads over the axle and reducing the load on the chippings spreading device 3.8 chippings spreading device spreading unit mounted on the rear of

32、a tipper truck, and which travels mainly in reverse during work NOTE The chippings spreading device can be fixed in the place of a tailgate or rear gate of the dumping body. The design of the chippings spreader device is adapted to the vehicle. 3.9 control station assembly which contains the control

33、 and adjustment equipment NOTE 1 The control station of a transported chippings spreader is typically installed on a platform, which may be fixed or articulated. The controls fulfil the following functions: on-off control of chippings spreading, adjustment of flow blade with or without indicator, ad

34、justment of spreading width, and adjustment of dumper tilt. NOTE 2 The control station of a self-propelled chippings spreader contains the controls to move the vehicle forward, supply the storage hoppers and spread the chippings. The control station enables the operator to monitor spreading and usua

35、lly contains: vehicle operation controls with speedometer and revolutions counter for each roller, the control to unhook the towed truck, conveyors, flow blade, bin gates or slanted blades and expandable hoppers. 3.10 power plant assembly which consists of mechanical components (engine, drive train

36、and driven axles) that contribute to accomplishing the drive function in order to move the chippings spreader during spreading and transfer 3.11 feed system system designed to transport chippings from receiving hopper to spreading hopper NOTE The receiving hopper receives the chippings discharged by

37、 a truck or semi-trailer. The truck of the semi-trailer is coupled to the chippings spreader by means of a rear-mounted tow hook. One or more conveyors may provide transfer of chippings from this hopper to the spreading hopper. The feed system (Figure 9) is composed of a receiving hopper to enable s

38、upply of conveyors, and the conveyors which transport the chippings from the receiving hopper to the spreading hopper. BSISO15644:20022ISO 46512002:4)E( ISO 2002 r llAithgs reservde 3 3.12 spreading hopper bin supplied by one or more conveyors, which spreads a defined quantity of chippings on the gr

39、ound cf. Figure 12 NOTE The spreading hopper may be equipped with one delivery roller for a fixed width hopper, or multiple rollers or expandable hoppers or moving hoppers. Each delivery roller (1) provided at the hopper base enables regulation of the chippings spreader flow. The roller speed may be

40、 automatically controlled by the travel speed of the chippings spreader. The passage of chippings may be regulated by opening the flow blade (2). A feeder (3) ensures a regular fall of chippings on the ground. The spreading width can be adjusted by bin gates or slanting blades (4) for a fixed width

41、hopper, the position of the expandable hoppers and the operation of cut-off plates to vary the width of chippings supplied to the spread roller, thereby varying the width of chippings laid onto the road surface. 3.13 dumping body tilt angle angle of tilt of a dumping body bottom in relation to the h

42、orizontal, taken along the longitudinal axis of the vehicle ( in Figure 1) 3.14 dumping body slope angle of a dumping body bottom in relation to the horizontal, taken along the transverse axis of the vehicle ( in Figure 1) 3.15 rear overhang of dumping body distance between the tipping axis and the

43、rear of the dumping body cf. Figure 8 3.16 clearance distance between the ground and the lowest part of a spreader, taken with the dumping body raised cf. Figure 8 4 Description of chippings spreader operation 4.1 Extraction or distribution of chippings from the dumper body bottom Extraction is unde

44、rtaken by a roller or by a conveyor (Figure 2) and enables automatic control of the chippings flow by the forward movement speed of the vehicle. Distribution is undertaken by a roller or by gravity (Figure 3). The flow of chippings does not depend on the feeder element, which requires a constant veh

45、icle speed and a constant angle of inclination of the dumping body bottom. For safety requirements for chippings spreaders, see EN 13020. BSISO15644:20023ISO :44651(2002)E 4 ISO 2002 Ar llithgr seresvde 4.2 Adjustment of chippings flow The adjustment of chippings flow per unit of width is illustrate

46、d in Figure 4. The flow blade (or register) enables adjustment of the thickness of the stream of chippings. Adjustment may be undertaken either by using a flow blade or a stop on the bin gates, or by adjusting the speed of the roller or conveyor. 4.3 Adjustment of spreading width This adjustment may

47、 be undertaken either by the bin gates or by slanting blades (Figure 5). 4.4 Automatic control by vehicle speed In order to obtain a constant proportion of chippings on the ground, the roller speed, or the conveyor speed, or the opening of the flow blade may be linked to the vehicle speed unless the

48、 latter is kept absolutely constant. 4.5 Diffuser A simple diffuser (Figure 6) typically has the following forms: smooth or partitioned; flat or curved. A diffuser with built-in or separate distributor (Figure 7) may be equipped on each side with a folding flap extension so that the spreading width

49、will then be greater than the vehicle width. 5 Commercial specifications 5.1 Transported chippings spreader 5.1.1 Main assemblies These shall be as shown in Figure 1: transporting vehicle; dumping body; chippings spreading device; control station; partial partition. 5.1.2 Dimensional characteristics 5.1.2.1 In transport position The dimensions shown in Figure 8 a) shall be specified: rear projection, (m