BS ISO 11630-1998 Cranes - Measurement of wheel alignment《起重机 轮位对准测量》.pdf
《BS ISO 11630-1998 Cranes - Measurement of wheel alignment《起重机 轮位对准测量》.pdf》由会员分享,可在线阅读,更多相关《BS ISO 11630-1998 Cranes - Measurement of wheel alignment《起重机 轮位对准测量》.pdf(16页珍藏版)》请在麦多课文档分享上搜索。
1、BRITISH STANDARD BS ISO 11630:1997 Cranes Measurement of wheel alignment ICS 53.020.20BSISO11630:1997 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comesintoeffect on 15 July 1998 BSI 05-1
2、999 ISBN 0 580 30121 4 National foreword This British Standard reproduces verbatim ISO 11630:1997 and implements it as the UK national standard. The UK participation in its preparation was entrusted by Technical Committee MHE/3, Cranes and derricks, to Subcommittee MHE/3/11, Crane safety and testing
3、, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgat
4、e them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the sec
5、tion entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application
6、. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theISO title page, page ii, pages 1 to 8 and a back cover. This standard has been updated (see copyright date
7、) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSISO11630:1997 BSI 05-1999 i Contents Page National foreword Inside front cover Foreword ii 1 Scope 1 2 Normative references
8、 1 3 Measurement of the alignment of crane wheels in plan view 1 4 Determination of the alignment of crane wheels in elevation profile 2 5 Determination of vertical deviations of crane wheels from the horizontal 3 Annex A (informative) Bibliography 8 Figure 1 4 Figure 2 5 Figure 3 6 Figure 4 7 Table
9、 1 Position of crane wheels in plan view 2 Table 2 Position of crane wheels in elevation profile 3 Table 3 Vertical distances from the raised wheels of the crane to the rail 3ii blankBSISO11630:1997 ii BSI 05-1999 Foreword ISO (the International Organization for Standardization) is a worldwide feder
10、ation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that commit
11、tee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the tec
12、hnical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least75% of the member bodies casting a vote. International Standard ISO11630 was prepared by Technical Committee ISO/TC96, Cranes, Subcommittee SC4, Test methods. Annex
13、 A of this International Standard is for information only.BSISO11630:1997 BSI 05-1999 1 1 Scope This International Standard establishes requirements for methods of measuring the alignment of crane wheels in accordance with ISO4310, ISO9373 and ISO12488-1. The procedures given are based on the use of
14、 optical methods for measurement, however this International Standard permits the use of other methods which ensure at least an equivalent accuracy of measurements. This International Standard applies to measurements on four-wheel cranes which move on rails (except railway cranes). NOTEProcedures fo
15、r measurements on cranes with more than four wheels are intended for the next edition of this International Standard. 2 Normative references The following standards contain provisions, which, through reference in this text, constitute provisions of this International Standard. At the time of publica
16、tion, the editions indicated were valid. All standards are subject to revision, and parties to agreement based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers
17、 of currently valid International Standards. ISO 4310:1981, Cranes Test code and procedures. ISO 9373:1989, Cranes and related equipment Accuracy requirements for measuring parameters during testing. 3 Measurement of the alignment of crane wheels in plan view The measurement of the alignment of whee
18、ls on cranes should proceed by the following steps: a) select the baseline for the coordinate system; b) establish the geodetic rectangle; c) measure distances from the sides of the geodetic rectangle to the wheels; d) calculate actual deviations of the wheels in plane from the design position. Meas
19、urements shall be made in accordance with ISO4310 and ISO9373. See also ISO12488-1. 3.1 Selection of baseline for the coordinate system To simplify the calculation of deviations, it is necessary to assume a base coordinate system and take measurements in reference to it. 3.1.1 From two select points
20、 on the external surface of the crane end-carriage, erect perpendiculars as shown inFigure 1. 3.1.2 On the perpendicular thus erected from the crane end-carriage, measure off segments Y 0of equal length. The theodolite should be positioned so that the direction of the collimating ray passes through
21、the ends of the segments Y 0 . 3.1.3 Taking the location of the theodolite as point O and arbitrary point of the theodolite collimating ray outside the crane as point R, then O and R will identify the direction of the x axis and serve as a base to establish the geodetic rectangle (seeFigure 1). 3.2
22、Establishing the geodetic rectangle 3.2.1 Based on the points O and R, the geodetic rectangle OPQR is established using the theodolite. The error in laying out corners of the rectangle should not exceed6seconds of arc. Identify the vertices P and Q by corresponding points as shown inFigure 2. 3.2.2
23、Measure distances OP, QR, PQ and OR. Differences in the dimensions (OP-QR) and (PQ-OR) shall not exceed a) for cranes with span S # 10m:2mm; b) for cranes with span S 10m: 2+0,1 (S10)mm. 3.3 Measurement of distances from the sides of the geodetic rectangle to the crane wheels 3.3.1 Establish referen
24、ces points corresponding to the crane wheels (seeFigure 2) and measure distances on the sides OR and PQ of the geodetic rectangle from points O, P, Q and R to the reference points, distances X O , X P , X Qand X R . Record the measurements inTable 1. 3.3.2 Measure distances Y O1 , Y O2 , Y P1 , Y P2
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSISO116301998CRANESMEASUREMENTOFWHEELALIGNMENT 起重 机轮 对准 测量 PDF

链接地址:http://www.mydoc123.com/p-583626.html