BS EN ISO 15976-2002 Closed end blind rivets with break pull mandrel and protruding head - St St《盘头离心牵引心轴的封闭型盲铆钉 St St》.pdf

《BS EN ISO 15976-2002 Closed end blind rivets with break pull mandrel and protruding head - St St《盘头离心牵引心轴的封闭型盲铆钉 St St》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 15976-2002 Closed end blind rivets with break pull mandrel and protruding head - St St《盘头离心牵引心轴的封闭型盲铆钉 St St》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN ISO 15976:2002 Incorporating Corrigenda Nos. 1 and 2 Closed end blind rivets with break pull mandrel and protruding head St/St The European Standard EN ISO 15976:2002 has the status of a British Standard ICS 21.060.40 BS EN ISO 15976:2002 This British Standard, having been pre

2、pared under the direction of the Engineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee and comes into effect on 20 November 2002 BSI 29 November 2004 ISBN 0 580 40780 2 National foreword This British Standard is the officia

3、l English language version of EN ISO 15976:2002. It is identical with ISO 15976:2002. BS EN ISO 15976:2002, together with BS EN ISO 14588:2001, BS EN ISO 14589:2001, BS EN ISO 15973:2000, BS EN ISO 15974:2001, BS EN ISO 15975:2002, BS EN ISO 15977:2002, BS EN ISO 15978:2002 and BS EN ISO 15979:2002,

4、 supersedes BS 7349-1:1993 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee FME/6, Rivets, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British

5、Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.

6、 This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible

7、international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the

8、 EN ISO title page, the EN ISO foreword page, the ISO title page, pages ii and iii, a blank page, pages 1 to 5, the Annex ZA page, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publicati

9、on Amd. No. Date Comments 14325 Corrigendum No. 1 3 February 2003 Correction to EN ISO foreword page and addition of Annex ZA page details 15345 Corrigendum No. 2 29 November 2004 Correction to National foreword supersession detailsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM ENISO15976 November20

10、02 ICS21.060.40 Englishversion Closedendblindrivetswithbreakpullmandrelandprotrudiing headSt/St(ISO15976:2002) Rivetsaveuglesrupturedetigecorpsferm,tte bombeSt/St(ISO15976:2002) GeschlosseneBlindnietemitSollbruchdornundFlachkopf St/St(ISO15976:2002) ThisEuropeanStandardwasapprovedbyCENon14October200

11、2. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheManagementCentreortoan

12、yCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheManagementCentrehasthesamestatusasthe official versions. CENmembersarethenationalstandardsbodiesofAust

13、ria,Belgium,CzechRepublic,Denmark,Finland,France,Germany,Greece, Iceland,Ireland,Italy,Luxembourg,Malta,Netherlands,Norway,Portugal,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B

14、1050Brussels 2002CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.ENISO15976:2002ECORRECTED20021218 Foreword Thisdocument(ENISO15976:2002)hasbeenpreparedbyTechnicalCommitteeISO/TC2 “Fasteners“incollaborationwithTechnicalCommitteeCEN/TC185“Threadedandno

15、n threadedmechanicalfastenersandaccessories“,thesecretariatofwhichisheldbyDIN. ThisEuropeanStandardshallbegiventhestatusofanationalstandard,eitherbypublicationof anidenticaltextorbyendorsement,atthelatestbyMay2003,andconflictingnationalstandards shallbewithdrawnatthelatestbyMay2003. AccordingtotheCE

16、N/CENELECInternalRegulations,thenationalstandardsorganizationsof thefollowingcountriesareboundtoimplementthisEuropeanStandard:Austria,Belgium,Czech Republic,Denmark,Finland,France,Germany,Greece,Iceland,Ireland,Italy,Luxembourg, Malta,Netherlands,Norway,Portugal,Spain,Sweden,SwitzerlandandtheUnitedK

17、ingdom. Endorsementnotice ThetextofISO15976:2002hasbeenapprovedbyCENasENISO15976:2002withoutany modifications. NOTENormativereferencestoInternationalStandardsarelistedinAnnexZA(normative). ENISO15976:2002 Reference number ISO 15976:2002(E)INTERNATIONAL STANDARD ISO 15976 First edition 2002-11-01 Clo

18、sed end blind rivets with break pull mandrel and protruding head St/St Rivets aveugles rupture de tige corps ferm, tte bombe St/St ENISO15976:2002DPlcsid Fremia ihTs PDF file mc yatnoaie nmt deddebyfepca.se Icca ncnadrow eitA hebods licsneilop gnic,y tihs file mirp eb yatniv ro deewb detu slahl ton

19、ide ebtlnu desse tt ehyfepacse wihce era hml era deddebicsnede to i dnasntlalde t noeh comtupfrep remroign tide ehti.gn Iwod nnlidaogn tihs fil,e trapies ccatpe tiereht nsnopser ehiiblity fo ton ifnriignA gnebods licnesilop gnic.y I ehTStneC Oarl Scerteiraat cacpets l oniibality it nihs .aera Ai ebo

20、ds a tedarmfo kra Aebod SystemI snctaropro.de teDials fo ts ehfotworp eracudts ust dec ortaet eihs PDF filc eeb na fi dnuot nlareneG eh Ifnler otait evt of ehil;e tP ehD-Fcrtaeiarap nomtesre wretpo eimizf deirp rotni.gn Evyre csah era t neebkat nesne ot eruaht tf ehili es siutlbaf esu roI yb eSO mem

21、idob rebse. It neh lnuikletneve y ttah a lborpem leratign ti ot is fnuo,d lpsaee ifnrom ttneC ehlar Secrteirata at tsserdda eh igleb nevwo. ISO 2002 Athgir lls serevr.de selnUs towrehise specfi,dei trap on fo this ilbupctanoi may cudorper ebtu ro deziliyna ni de fomr yb ro nam y,snae lecetinorc m ro

22、ecinahcal, inclidutohp gnocpoiym dna gnicrfoilm, wittuoh repmissii now nritif gnrom ietreh ISa Ot tserdda ehs lebwo I roSOs membre ydob it neh ctnuoo yrf ttseuqer eh.re ISO cirypothg fofice saCe tsopale 65 eneG 1121-HC 02 av leT. 4 + 10 947 22 1 11 xaF0 947 22 14 + 9 74 E-mial coirypthgis.oc h Web w

23、w.wiso.ch ii ENISO15976:2002 iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body inter

24、ested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical

25、 Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the te

26、chnical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of pat

27、ent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15976 was prepared by Technical Committee ISO/TC 2, Fasteners. Annex A of this International Standard is for information only. ENISO15976:2002INTENRATIONAL TSANDADR IS:67951 O2002(E)I SO 2002 All irthgs

28、ersedevr 1Closed end blind rivets with break pull mandrel and protruding head St/St 1 Scope This International Standard specifies dimensional and mechanical characteristics and application data for closed end blind rivets with break pull mandrel and protruding head, with a steel body (St) and an ste

29、el mandrel (St) and with nominal diameters, d, from 3,2 mm up to and including 6,4 mm. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments

30、to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition o

31、f the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 3269:2000, Fasteners Acceptance inspection ISO 4042:1999, Fasteners Electroplated coatings ISO 4520:1981, Chromate conversion coatings of electroplated zinc and cad

32、mium coatings ISO 14588:2000, Blind rivets Terminology and definitions ISO 14589:2000, Blind rivets Mechanical testing 3 Dimensions 3.1 General Symbols and designations of dimensions are specified in ISO 14588. 3.2 Rivet dimensions See Figure 1 and Table 1. ENISO15976:20021ISO 15976:2002(E) 2 I SO 2

33、002 All irthgs ersedevrFigure 1 Rivet dimensions Table 1 Rivet dimensions Dimensions in millimetres nom. 3,2 4 4,8 6,4 max. 3,28 4,08 4,88 6,48 d min. 3,05 3,85 4,65 6,25 max. 6,7 8,4 10,1 13,4 d kmin. 5,8 6,9 8,3 11,6 Rivet body k max. 1,3 1,7 2 2,7 d mmax. 2 2,35 2,95 3,9 Mandrel p min. 25 25 27 2

34、7 Rivet length l nom. = min. max. Recommended grip ranges a6 7 0,5 to 1,5 0,5 to 1,5 8 9 1,5 to 3,0 1,5 to 3,0 0,5 to 3,0 10 11 3 to 5 3 to 5 3 to 5 12 13 5,0 to 6,5 5,0 to 6,5 5,0 to 6,5 15 16 6,5 to 10,5 6,5 to 10,5 3,0 to 6,5 16 17 6,5 to 8,0 21 22 8,0 to 12,5 NOTE The rivet body dimensions are g

35、enerated from the design formulae specified in the annex A. aThe grip ranges of rivets with dimensions as given in Table 1, with the material combination as given in clause 4, are specified by the minimum and maximum grip lengths. The minimum grip lengths are given as a recommendation only. It may b

36、e possible to go into individual cases below the minimum values. ENISO15976:20022ISO 15976:2002(E) I SO 2002 All irthgs ersedevr 33.3 Clearance hole diameters The diameters of the clearance holes (d h1 ) to accommodate the rivet in the components to be fastened are given in Table 2. Table 2 Clearanc

37、e hole diameters Dimensions in millimetres d d h1nom. min. max. 3,2 3,3 3,4 4 4,1 4,2 4,8 4,9 5,0 6,4 6,5 6,6 Non-conformance to the values listed in Table 2 may result in assembly difficulties and/or reduction in the shear and tensile loads specified in Table 3. When necessary to facilitate alignme

38、nt, only the component on the access side may have a clearance hole larger than specified in Table 2 (see Figure 2). This may also result in a reduction of the shear and tensile loads specified in Table 3. aEnlarged clearance hole Figure 2 Enlarged clearance hole to facilitate alignment 4 Material a

39、nd finish Blind rivets in accordance with this International Standard shall have a rivet body made of steel (St) and a mandrel made of steel (St) and shall have mechanical properties as specified in clause 5. Material specification is at the discretion of the manufacturer. The surface of rivet body

40、and mandrel shall be zinc plated 5 m minimum in accordance with ISO 4042 measured at the rivet head. The chromate conversion coating shall be c2C in accordance with ISO 4520:1981. The complete finish designation is then Fe/Zn5c2C. ENISO15976:20023ISO 15976:2002(E) 4 I SO 2002 All irthgs ersedevr5 Me

41、chanical properties The minimum shear load, minimum tensile load and maximum mandrel break load shall be as specified in Table 3 when tested in accordance with ISO 14589. Table 3 Mechanical properties Shear load Tensile load Mandrel break load d nom. min. min. max. mm N N N 3,2 1 150 1 300 4 000 4 1

42、 700 1 550 5 700 4,8 2 400 2 800 7 500 6,4 3 600 4 000 10 500 6 Workmanship Rivets shall be free from burrs and harmful defects and shall have well-formed heads and shanks. After setting, rivets shall not show evidence of cracking when viewed at 5 magnification. 7 Acceptance testing If there is no o

43、ther agreement, acceptance inspection in accordance with ISO 3269 applies. 8 Designation EXAMPLE A closed end blind rivet, with break pull mandrel and protruding head, with nominal diameter d = 4 mm and nominal length l = 12 mm with a steel body (St) and a steel mandrel (St) is designated as follows

44、: Blind rivet ISO 15976 - 4 12 - St/St ENISO15976:20024ISO 15976:2002(E) I SO 2002 All irthgs ersedevr 5Annex A (informative) Design formulae A.1 General Blind rivets in accordance with this International Standard comply with the following design formulae and tolerances. A.2 Shank diameter The maxim

45、um shank diameter complies with the formula: d max= d nom+ 0,08 mm The minimum shank diameter complies with the formula: d min= d nom 0,15 mm A.3 Head diameter The maximum head diameter complies with the formula: d k max= 2,1 d nomrounded to one decimal place. A.4 Head diameter tolerance The head di

46、ameter tolerance is h16 for d nomu 3,2 mm and h17 for d nom 3,2 mm. A.5 Head height The maximum head height complies with the formula: k max= 0,415 d nomrounded to one decimal place. A.6 Clearance hole diameter The clearance hole diameter for blind rivet application complies with the formulae: d h1

47、max= d nom+ 0,2 mm d h1 min= d nom+ 0,1 mm ENISO15976:20025AnnexZA (normative) Normativereferencestointernationalpublications withtheirrelevantEuropeanpublications ThisEuropeanStandardincorporatesbydatedorundatedreference,provisionsfromother publications.Thesenormativereferencesarecitedattheappropriateplacesinthetextandthe publicationsarelistedhereafter.Fordatedreferences,subsequentamendmentstoorrevisionsof anyofthesepublicationsapplytothisEuropeanStandardonlywhenincorporatedinitby amendmentorrevision.Forundatedreferencesthelatestediti