BS EN ISO 1-2016 Geometrical product specifications (GPS) Standard reference temperature for the specification of geometrical and dimensional properties《产品几何技术规范(GPS) 规范几何和尺寸性能的标准参.pdf

《BS EN ISO 1-2016 Geometrical product specifications (GPS) Standard reference temperature for the specification of geometrical and dimensional properties《产品几何技术规范(GPS) 规范几何和尺寸性能的标准参.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 1-2016 Geometrical product specifications (GPS) Standard reference temperature for the specification of geometrical and dimensional properties《产品几何技术规范(GPS) 规范几何和尺寸性能的标准参.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO 1:2016Geometrical productspecifications (GPS) Standard referencetemperature for thespecification of geometricaland dimensional properties(ISO 1:2016)BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN ISO 1:2016 BRITISH STANDARDNational forewordThis Briti

2、sh Standard is the UK implementation of EN ISO 1:2016. Itsupersedes BS EN ISO 1:2002 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee TDW/4, Technical Product Realization.A list of organizations represented on this committee can be obtained on request t

3、o its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 88599 0 ICS 17.040.01 Compliance with a British Sta

4、ndard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN

5、 ISO 1 September 2016 ICS 17.040.01 Supersedes EN ISO 1:2002English Version Geometrical product specifications (GPS) - Standard reference temperature for the specification of geometrical and dimensional properties (ISO 1:2016) Spcification gomtrique des produits (GPS) - Temprature normale de rfrence

6、 pour la spcification des proprits gomtriques et dimensionnelles (ISO 1:2016) Geometrische Produktspezifikation (GPS) - Referenztemperatur fr geometrische Produktspezifikation und -prfung (ISO 1:2016) This European Standard was approved by CEN on 7 August 2016. CEN members are bound to comply with t

7、he CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Manageme

8、nt Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status

9、 as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

10、Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All

11、 rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 1:2016 EBS EN ISO 1:2016EN ISO 1:2016 (E) 3 European foreword This document (EN ISO 1:2016) has been prepared by Technical Committee ISO/TC 213 “Dimensional and geometrical product speci

12、fications and verification“ in collaboration with Technical Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identi

13、cal text or by endorsement, at the latest by March 2017, and conflicting national standards shall be withdrawn at the latest by March 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held respo

14、nsible for identifying any or all such patent rights. This document supersedes EN ISO 1:2002. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus,

15、 Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Ki

16、ngdom. Endorsement notice The text of ISO 1:2016 has been approved by CEN as EN ISO 1:2016 without any modification. BS EN ISO 1:2016ISO 1:2016(E)Foreword ivIntroduction v1 Scope . 12 Terms and definitions . 13 Standard reference temperature value for the specification of geometrical and dimensional

17、 properties . 1Annex A (informative) Use of the reference temperature specification 2Annex B (informative) Relation to the GPS matrix model 3Bibliography 4 ISO 2016 All rights reserved iiiContents PageBS EN ISO 1:2016ISO 1:2016(E)ForewordISO (the International Organization for Standardization) is a

18、worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented

19、 on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop thi

20、s document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Di

21、rectives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the deve

22、lopment of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO

23、specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html .The committee responsible for this document is

24、ISO/TC 213, Dimensional and geometrical product specifications and verification.This third edition cancels and replaces the second edition (ISO 1:2002), which has been technically revised. Specifically, the following points have changed: the standard reference temperature definition has been include

25、d; consequently, the title, introduction and scope, have been changed; the general definition of reference temperature has been included.iv ISO 2016 All rights reservedBS EN ISO 1:2016ISO 1:2016(E)IntroductionThis International Standard is a geometrical product specification (GPS) standard and is to

26、 be regarded as a fundamental GPS Standard (see ISO 14638:20151). For more detailed information on the relationship of this International Standard to other standards and the GPS matrix model, see Annex B.The definitions of the units, including those of length and temperature, are adopted by the Gene

27、ral Conference of Weights and Measures (CGPM) under the authority of the Convention of the Metre. These definitions are maintained in the SI brochure.5The unit of length, the metre, is independent of temperature. The current definition of the metre6is based on the distance light travels in vacuum du

28、ring a unit of time. However, a physical object is subject to thermal expansion and consequently, its geometrical and dimensional properties are dependent on its temperature. Specifying a reference temperature allows the geometrical and dimensional properties of a physical object to be unambiguously

29、 stated. ISO 2016 All rights reserved vBS EN ISO 1:2016BS EN ISO 1:2016Geometrical product specifications (GPS) Standard reference temperature for the specification of geometrical and dimensional properties1 ScopeThis International Standard defines the concepts of a reference temperature and of the

30、standard reference temperature, and specifies the standard reference temperature value for the specification of geometrical and dimensional properties of an object. Some examples of geometrical and dimensional properties include size, location, orientation (including angle), form and surface texture

31、 of a workpiece.This International Standard is also applicable to the definition of the measurand used in verification or calibration.2 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.2.1reference temperaturetemperature of an object, having a uniform

32、 temperature, specified as part of the definition of a geometrical or dimensional propertyNote 1 to entry: The specification of a geometrical or dimensional property is typically given in technical product documentation, e.g., on an engineering drawing or in a CAD file, or in the specification of th

33、e measurand (the quantity intended to be measured).2.2standard reference temperatureinternationally agreed-upon reference temperatureNote 1 to entry: In prior editions of this International Standard, the term “standard reference temperature” was defined as its assigned numerical value, i.e. 20 C. In

34、 this edition, the definition of the reference temperature (2.1) and the assignment of a standardized value to this temperature are separately addressed (Clause 3).3 Standard reference temperature value for the specification of geometrical and dimensional propertiesThe standard reference temperature

35、 value for the specification of geometrical and dimensional properties shall be fixed at 20 C. Unless otherwise explicitly specified, the reference temperature for geometrical and dimensional properties of workpieces shall be the standard reference temperature. See Annex A for information on the use

36、 of the reference temperature specification.NOTE 1 There is only one standard reference temperature value and it is fixed at 20 C. However, this does not prevent a different (non-standard) reference temperature from being specified for all geometrical and dimensional properties of a workpiece or for

37、 a specific geometrical or dimensional property on a workpiece, provided it is explicitly stated as part of the specification.NOTE 2 The specification of a non-standard reference temperature may increase the measurement uncertainty during verification because most dimensional measuring equipment and

38、 gauges are calibrated with their measurand defined at the standard reference temperature.INTERNATIONAL STANDARD ISO 1:2016(E) ISO 2016 All rights reserved 1BS EN ISO 1:2016ISO 1:2016(E)Annex A (informative) Use of the reference temperature specificationSpecifying geometrical and dimensional propert

39、ies at a single temperature value can raise questions sincea) the functional requirements of any physical workpiece include other temperatures,b) verification cannot physically occur at an exact, uniform temperature.Regarding the issue that workpiece functional requirements include other temperature

40、s, it is important to note that a designer typically specifies not only the requirements on the geometric and dimensional properties of the workpiece (usually at the standard reference temperature value), but also separate requirements on the material properties of the workpiece. Combining the knowl

41、edge of how a specified material behaves at different temperatures and the specified geometric and dimensional properties at a single temperature can allow a designer to ensure a workpiece will meet geometric and dimensional functional requirements over a range of temperatures.Regarding the issue th

42、at any geometrical or dimensional verification inevitably occurs at a temperature different than the reference temperature, an adequate correction for that difference is necessary (see for example ISO/IEC Guide 99:2007, 2.3, Note 32). In some cases, the correction might be zero (i.e. no correction i

43、s performed); however, in all cases, it is necessary that the lack of knowledge of the exact correction be accounted for appropriately in the measurement uncertainty see for example ISO/IEC GUIDE 98-3:2008, 3.3.2 b)3.Most measuring systems are designed to produce measurement results specified at the

44、 standard reference temperature value of 20 C even though they may be operating at a different temperature. In this case, deviations from the standard reference temperature for either the measuring system or the workpiece under measurement lead to additional measurement uncertainty contributors; see

45、 ISO/TR 160154for additional information. The term reference temperature should not be confused with the term rated operating condition.2 ISO 2016 All rights reservedBS EN ISO 1:2016ISO 1:2016(E)Annex B (informative) Relation to the GPS matrix modelB.1 GeneralThe ISO GPS matrix model given in ISO 14

46、638 gives an overview of the ISO GPS system of which this standard is a part.B.2 Information about this International Standard and its useThis International Standard is used whenever GPS specifications for workpieces and measuring equipment are given. It constitutes the basis for the evaluation of m

47、easurement uncertainty.B.3 Position in GPS matrix modelThis standard is a fundamental GPS standard. The rules and principles given in this standard apply to all general and complementary ISO GPS standards in the ISO GPS matrix. See Table B.1.Table B.1 Position in the GPS matrix modelChain linksA B C

48、 D E F GSymbols and indica-tionsFeature re-quirementsFeature propertiesConform-ance and non-con-formanceMeasurement Measurement equipmentCalibrationsSize Distance Form Orientation Location Run-out Profile sur-face texture Areal sur-face texture Surface im-perfections B.4 Related International Standa

49、rdsThe related standards are those of the chains of standards indicated in Table B.1. ISO 2016 All rights reserved 3BS EN ISO 1:2016ISO 1:2016(E)Bibliography1 ISO 14638, Geometrical product specifications (GPS) Matrix model2 ISO/IEC Guide 99:2007, International vocabulary of metrology Basic and general concepts and associated terms (VIM)3 ISO/IEC Guide 98-3:2008, Uncertainty of measurement Part 3: G