BS EN 61629-2-1997 Aramid pressboard for electrical purposes - Methods of test《电气设备用芳族聚酰胺板 试验方法》.pdf

《BS EN 61629-2-1997 Aramid pressboard for electrical purposes - Methods of test《电气设备用芳族聚酰胺板 试验方法》.pdf》由会员分享，可在线阅读，更多相关《BS EN 61629-2-1997 Aramid pressboard for electrical purposes - Methods of test《电气设备用芳族聚酰胺板 试验方法》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 61629-2:1997 IEC 1629-2: 1996 Aramid pressboard for electrical purposes Part 2: Methods of test The European Standard EN 61629-2:1996 has the status of a British Standard ICS 29.035.10BS EN 61629-2:1997 This British Standard, having been prepared under the directionof the Elec

2、trotechnical Sector Board, was published underthe authority of the Standards Board and comes intoeffect on 15 May 1997 BSI 01-1999 The following BSI references relate to the work on this standard: Committee reference GEL/15 Draft for comment 94/216488 DC ISBN 0 580 26675 3 Committees responsible for

3、 this British Standard The preparation of this British Standard was entrusted by Technical Committee GEL/15, Insulating materials, to Subcommittee GEL/15/3, Material specifications, upon which the following bodies were represented: Adhesive Tape Manufacturers Association British Capacitors Manufactu

4、rers Association (BEAMA Ltd.) British Industrial Ceramic Manufacturers Association British Plastics Federation ERA Technology Ltd. Electrical and Electronic Insulation Association (BEAMA Ltd.) Federation of the Electronics Industry Transmission and Distribution Association (BEAMA Ltd.) The following

5、 bodies were also represented in the drafting of the standard, through subcommittees and panels: Electricity Association British Telecommunications Plc Diamond Fibre Company Ltd. Paper Federation of Great Britain Rotating Electrical Machines Association (BEAMA Ltd.) Royal Society of Chemistry Amendm

6、ents issued since publication Amd. No. Date CommentsBS EN 61629-2:1997 BSI 01-1999 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN 61629-2 3BS EN 61629-2:1997 ii BSI 01-1999 National foreword This British Standard has been prepared by Subcommittee

7、 GEL/15/3 and is the English language version of EN61629-2:1996 Aramid pressboard for electrical purposes Part2: Methods of test published by the European Committee for Electrotechnical Standardization (CENELEC). It is identical with IEC1629-2:1996 published by the International Electrotechnical Com

8、mission(IEC). IEC1629 consists of the following parts, under the general title Aramid pressboard for electrical purposes: Part 1: Definitions, designations and general requirements; Part 2: Methods of test; Part 3: Specifications for individual materials. A British Standard does not purport to inclu

9、de all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references Publication referred to Corresponding British Standard EN 60641-2:19

10、95 (IEC 641-2:1979) BS EN 60641 Specification for pressboard and presspaper for electrical purposes Part 2:1996 Methods of test EN 61629-1:1996 (IEC 1629-1:1996) BS EN 61629 Aramid pressboard for electrical purposes Part 1:1996 Definitions, designations and general requirements Summary of pages This

11、 document comprises a front cover, an inside front cover, pagesi andii, theEN title page, pages2 to4 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on theinside front cover.EUROPEAN STANDAR

12、D NORME EUROPENNE EUROPISCHE NORM EN 61629-2 December 1996 ICS 29.040.20 Descriptors: Solid electrical insulating materials, paper, paper boards, aramid fibres, designation, tests specimen preparation English version Aramid pressboard for electrical purposes Part 2: Methods of test (IEC 1629-2:1996)

13、 Carton comprim aramide usages lectriques Partie 2: Mthodes dessai (CEI 1629-2:1996) Aramid-Tafelprespan fr elektrotechnische Zwecke Teil 2: Prfverfahren (IEC 1629-2:1996) This European Standard was approved by CENELEC on 1996-10-01. CENELEC members are bound to comply with the CEN/CENELEC Internal

14、Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member

15、. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC m

16、embers are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit

17、 Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1996 Copyright reserved to CENELEC members Ref. No. EN 61629-2:1996 EEN 61629-2:1996 BSI 01-1999 2 Foreword The text of document 15C/619/FDIS, future e

18、dition1 of IEC1629-2, prepared by SC15C, Specifications, of IECTC15, Insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN61629-2 on1996-10-01. The following dates were fixed: Annexes designated “normative” are part of the body of the standard. In thi

19、s standard, annexZA is normative. Annex ZA has been added by CENELEC. Endorsement notice The text of the International Standard IEC 1629-2:1996 was approved by CENELEC as a European Standard without any modification. Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 General note 3 4 Cond

20、itioning of test specimens 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications 4 latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 1997-07-0

21、1 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 1997-07-01EN61629-2:1996 BSI 01-1999 3 1 Scope This part of IEC1629 gives the methods of test applicable for the materials classified in IEC1629-1. 2 Normative references The following normative document

22、s contain provisions which, through reference in this text, constitute provisions of this part of IEC1629. At the time of publication, the editions indicated were valid. All normative documents are subject to revision, and parties to agreements based on IEC1629 are encouraged to investigate the poss

23、ibility of applying the most recent editions of the normative documents indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. IEC 641-2:1979, Specification for pressboard and presspaper for electrical purposes Part 2: Method of test Amendment 1 (1993)

24、. IEC 1629-1:1996, Aramid pressboard for electrical purposes Part 1: Definitions, designations and general requirements. 3 General note Aramid pressboards for electrical purposes are tested according to the requirements of IEC641-2 with the exception described in4.2. 4 Conditioning of test specimens

25、 4.1 Aramid board type APB-LD, APB and APB-C are conditioned according to clause1 of IEC641-2. 4.2 Aramid board APB-HD shall also be conditioned according to clause1 of IEC641-2, but in case of dispute the conditioning time shall be: Nominal thickness: # 2,0mm 2,0 mm and # 5,0mm 5,0 mm Time: 120 h 2

26、40h 360hEN 61629-2:1996 4 BSI 01-1999 Annex ZA (normative) Normative references to international publications with their corresponding European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at

27、the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of t

28、he publication referred to applies (including amendments). NOTEWhen an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC641-2 1979 Specification for pressboard and presspaper for electrical purpo

29、ses Part 2: Methods of test +A1 1993 EN 60641-2 a 1995 IEC 1629-1 1996 Aramid pressboard for electrical purposes Part1: Definitions, designations and general requirements EN 61629-1 1996 a EN60641-2 includes corrigendum October1994 to IEC641-2.5 blankBSI 389 Chiswick High Road London W4 4AL | | | |

30、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independe

31、nt national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they po

32、ssess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the ident

33、ity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and for

34、eign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Infor

35、mation on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact

36、the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 70

37、02. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retr

38、ieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designati

39、ons. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.