BS EN 61629-1-1997 Aramid pressboard for electrical purposes - Definitions designations and general requirements《电气设备用芳族聚酰胺压纸板 定义、名称及一般要求》.pdf

《BS EN 61629-1-1997 Aramid pressboard for electrical purposes - Definitions designations and general requirements《电气设备用芳族聚酰胺压纸板 定义、名称及一般要求》.pdf》由会员分享，可在线阅读，更多相关《BS EN 61629-1-1997 Aramid pressboard for electrical purposes - Definitions designations and general requirements《电气设备用芳族聚酰胺压纸板 定义、名称及一般要求》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 61629-1:1997 IEC 1629-1: 1996 Aramid pressboard for electrical purposes Part 1: Definitions, designations and general requirements The European Standard EN 61629-1:1996 has the status of a British Standard ICS 29.035.10BSEN61629-1:1997 This British Standard, having been prepar

2、ed under the directionof the ElectrotechnicalSector Board, was published under the authorityof the Standards Boardand comes into effect on 15 May 1997 BSI 09-1999 The following BSI references relate to the work on this standard: Committee reference GEL/15 Draft for comment 94/214037 DC ISBN 0 580 26

3、674 5 Committees responsible for this British Standard The preparation of this British Standard was entrusted by Technical Committee GEL/15, Insulating materials, to Subcommittee GEL/15/3, Material specifications, upon which the following bodies were represented: Adhesive Tape Manufacturers Associat

4、ion British Capacitors Manufacturers Association (BEAMA Ltd.) British Industrial Ceramic Manufacturers Association British Plastics Federation ERA Technology Ltd. Electrical and Electronic Insulation Association (BEAMA Ltd.) Federation of the Electronics Industry Transmission and Distribution Associ

5、ation (BEAMA Ltd.) The following bodies were also represented in the drafting of the standard, through subcommittees and panels: Electricity Association British Telecommunications plc Diamond Fibre Company Ltd. Paper Federation of Great Britain Rotating Electrical Machines Association (BEAMA Ltd.) R

6、oyal Society of Chemistry Amendments issued since publication Amd. No. Date CommentsBSEN61629-1:1997 BSI 09-1999 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN 61629-1 3 List of references Inside back coverBSEN61629-1:1997 ii BSI 09-1999 National

7、 foreword This British Standard has been prepared by Subcommittee GEL/15/3 and is the English language version of EN 61629-1:1996 Aramid pressboard for electrical purposes Part 1: Definitions, designations and general requirements published by the European Committee for Electrotechnical Standardizat

8、ion (CENELEC). It is identical with IEC1629-1:1996 published by the International Electrotechnical Commission (IEC). IEC 1629 consists of the following parts, under the general title Aramid pressboard for electrical purposes: Part 1: Definitions, designations and general requirements; Part 2: Method

9、s of test; Part 3: Specifications for individual materials. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from

10、legal obligations. Cross-references Publication referred to Corresponding British Standard BS EN 60641 Specification for pressboard and presspaper for electrical purposes EN 60641-1:1995 (IEC 641-1:1979) Part 1:1996 Definitions and general requirements EN 60641-2:1995 (IEC 641-2:1979) Part 2:1996 Me

11、thods of test EN 60641-3-1:1994 (IEC 641-3-1:1992) Part 3 Specifications for individual materials Sheet 1:1994 Requirements for pressboard, types B.0.1, B.2.1, B.2.3, B.3.1, B.3.3, B.4.1, B.4.3, B.5.1, B.6.1 and B.7.1 Summary of pages This document comprises a front cover, an inside front cover, pag

12、es i and ii, the EN title page, pages 2 to 6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM

13、 EN 61629-1 December 1996 ICS 29.040.20 Descriptors: Solid electrical insulating materials, paper, paper boards, aramid fibres, designation, specification, thickness, marking, packing English version Aramid pressboard for electrical purposes Part 1: Definitions, designations and general requirements

14、 (IEC 1629-1:1996) Carton comprim aramide usages lectriques Partie 1: Dfinitions, dsignations etprescriptions gnrales (CEI 1629-1:1996) Aramid-Tafelprespan fr elektrotechnische Zwecke Teil 1: Begriffe, Kennzeichnung undallgemeineAnforderungen (IEC 1629-1:1996) This European Standard was approved by

15、CENELEC on 1996-10-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national sta

16、ndards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and no

17、tified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland

18、and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1996 Copyright reserved to CENELEC members Ref. No. EN 61629-1

19、:1996 EEN61629-1:1996 BSI 09-1999 2 Foreword The text of document 15C/618/FDIS, future edition1 of IEC1629-1, prepared by SC 15C, Specifications, of IEC TC15, Insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN61629-1 on1996-10-01. The following dat

20、es were fixed: Endorsement notice The text of the International Standard IEC1629-1:1996 was approved by CENELEC as a European Standard without any modification. In the official version, for Annex A, Bibliography, the following notes have to be added for the standards indicated: Contents Page Forewor

21、d 2 1 Scope 3 2 Definitions 3 3 Designation 3 4 General requirements 3 5 Thickness 4 6 Conditions of supply Packaging 4 7 Marking 4 Annex A (informative) Bibliography 5 latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsem

22、ent (dop) 1997-07-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 1997-07-01 IEC 641-1 NOTEHarmonized, together with its amendment 1:1993, as EN60641-1:1995 (not modified). IEC 641-2 NOTEHarmonized, together with its corrigendum 1994 and its amendmen

23、t 1:1993, as EN 60641-2:1995 (not modified). IEC 641-3-1 NOTEHarmonized as EN 60641-3-1:1994 (not modified).EN61629-1:1996 BSI 09-1999 3 1 Scope This part of IEC1629 contains the definitions, designations and general requirements of aramid pressboard for electrical purposes. Materials which conform

24、to this specification meet established levels of performance. However, the selection of a material for a specific application should be based on the actual requirements necessary for the adequate performance in that application and not based on this specification alone. While the primary use of thes

25、e materials is an electrical insulation, there is no intent to discourage their use in other applications for which their properties may make them suitable. 2 Definitions For the purpose of this part of IEC1629, the following definitions apply: 2.1 aramid pressboard board produced normally on an int

26、ermittent board-making machine from pulp made from high temperature resistant aramid fibres and fibrids which are produced of synthetic polyamid having at least85% of amide linkage attached directly to two aromatic rings 2.2 calendered aramid pressboard aramid pressboard which is densified by a subs

27、equent calendering process 2.3 high-density aramid pressboard aramid pressboard which is densified by a subsequent heat-pressing operation 3 Designation The aramid pressboard materials shall be designated as follows: 4 General requirements 4.1 Composition The material shall be manufactured from aram

28、id high temperature resistant fibres, according to the definition given in2.1. 4.2 Finish Boards shall be plane, free from local deformations or surface defects. All boards shall be supplied with trimmed edges. The surface texture of types APB-LD, APB and APB-C shows a cloth mark impression. Type AP

29、B-HD has a smoother surface than the other types of aramid pressboard and an off-white aspect. 4.3 Machinability When cut, sawn, punched or otherwise machined in accordance with the recommendations of the supplier, the board shall not show any undue splitting, cracking, or ragging of the edges. Type

30、 Description Apparent density (g/cm 3 ) APB-LD Low density 0,5 to 0,7 APB Standard density 0,6 to 1,0 APB-C Medium density/calendered 0,8 to 1,1 APB-HD High density/heat compressed 1,0 to 1,2EN61629-1:1996 4 BSI 09-1999 5 Thickness 5.1 Preferred nominal thicknesses of the boards 5.2 Deviation of thi

31、ckness The deviation from nominal thickness shall not exceed the values which will be given in the sheets of the futureIEC 1629-3 1) . 6 Conditions of supply Packaging The material shall be supplied in a packaging which ensures adequate protection during handling, transportation, and storage. 7 Mark

32、ing 7.1 Identification Every material consignment shall be legibly marked with a clearly identifiable code. 7.2 Marking material Any marking material used on the pressboard shall be electrically neutral, oil resistant and non-polluting to oil. Type Preferred nominal thicknesses (mm) APB-LD 1,6 3,2 A

33、PB 1,0 1,5 2,0 2,4 3,0 4,0 5,0 APB-C 0,8 1,2 1,7 2,1 2,7 3,7 4,7 APB-HD 1,0 1,5 2,0 3,0 3,3 4,0 4,8 6,0 6,4 8,0 9,6 1) Under consideration.EN61629-1:1996 BSI 09-1999 5 Annex A (informative) Bibliography IEC 641-1:1979, Specification for pressboard and presspaper for electrical purposes Part 1: Defin

34、itions and general requirements. IEC 641-2:1979, Specification for pressboard and presspaper for electrical purposes Part 2: Methods of test. IEC 641-3-1:1992, Specification for pressboard and presspaper for electrical purposes Part3:Specifications for individual materials Sheet 1: Requirements for

35、pressboard, types B.0.1, B.2.1, B.2.3, B.3.1, B.3.3, B.4.1, B.4.3, B.5.1, B.6.1 and B.7.1. 6 blankBSEN61629-1:1997 BSI 09-1999 List of references See national foreword.BS EN 61629-1:1997 IEC 1629-1: 1996 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent n

36、ational body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess t

37、he latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of w

38、hich can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards

39、 publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards B

40、SI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centr

41、e. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright

42、 Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any

43、 form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.