BS EN 60851-4-2016 Winding wires Test methods Chemical properties《绕组线试验方法 化学性能》.pdf

《BS EN 60851-4-2016 Winding wires Test methods Chemical properties《绕组线试验方法 化学性能》.pdf》由会员分享，可在线阅读，更多相关《BS EN 60851-4-2016 Winding wires Test methods Chemical properties《绕组线试验方法 化学性能》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、Winding wires TestmethodsPart 4: Chemical propertiesBS EN 60851-4:2016BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06National forewordThis British Standard is the UK implementation of EN 60851-4:2016. It isidentical to IEC 60851-4:2016. It supersedes BS EN 60851-4:1

2、998 which iswithdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee L/-/99, Miscellaneous Standards - Electrical.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessa

3、ry provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 86853 5ICS 29.060.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was pu

4、blished under the authority of theStandards Policy and Strategy Committee on 31 October 2016.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 60851-4:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60851-4 October 2016 ICS 29.060.10 Supersedes EN 60851-4

5、:1996 English Version Winding wires - Test methods - Part 4: Chemical properties (IEC 60851-4:2016) Fils de bobinage - Mthodes dessai - Partie 4: Proprits chimiques (IEC 60851-4:2016) Wickeldrhte - Prfverfahren - Teil 4: Chemische Eigenschaften (IEC 60851-4:2016) This European Standard was approved

6、by CENELEC on 2016-08-10. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national

7、standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own la

8、nguage and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, Fr

9、ance, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de N

10、ormalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 60851-4:2016 E BS EN 60851-4:2016EN

11、 60851-4:2016 2 European foreword The text of document 55/1578/FDIS, future edition 3 of IEC 60851-4, prepared by IEC/TC 55 “Winding wires“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60851-4:2016. The following dates are fixed: latest date by which the document has

12、to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2017-05-10 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2019-08-10 This document supersedes EN 60851-4:1996 Attention is drawn to the p

13、ossibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60851-4:2016 was approved by CENELEC as a European

14、Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60264 Series NOTE Harmonized as EN 60264 Series. IEC 60317 Series NOTE Harmonized as EN 60317 Series. IEC 60851 Series NOTE Harmonized as EN 60851 Serie

15、s. BS EN 60851-4:2016EN 60851-4:2016 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated

16、 references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date

17、 information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu Publication Year Title EN/HD Year IEC 60296 - Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear EN 60296 - IEC 60554-1 1977 Spe

18、cification for cellulosic papers for electrical purposes - Part 1: Definitions and general requirements - - IEC 60851-1 - Winding wires - Test methods - Part 1: General EN 60851-1 - IEC 60851-3 2009 Winding wires - Test methods - Part 3: Mechanical properties EN 60851-3 2009 IEC 60851-5 2008 Winding

19、 wires - Test methods - Part 5: Electrical properties EN 60851-5 2008 ISO 9453 - Soft solder alloys - Chemical compositions and forms EN ISO 9453 - BS EN 60851-4:2016 2 IEC 60851-4:2016 IEC 2016 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope 7 2 Normative references. 7 3 Test 12: Resistance to solve

20、nts . 7 3.1 General . 7 3.2 Equipment 8 3.3 Procedure . 8 4 16: Resistance to refrigerants 9 4.1 General . 9 4.2 Extraction . 9 4.2.1 Principle 9 4.2.2 Equipment . 9 4.2.3 Specimen. 11 4.2.4 Procedure 11 4.2.5 Result 12 4.3 Breakdown voltage 12 4.3.1 Principle 12 4.3.2 Procedure 12 4.3.3 Result 13 5

21、 Test 17: Solderability . 13 5.1 General . 13 5.2 Equipment 13 5.3 Procedure . 14 6 Test 20: Resistance to hydrolysis and to transformer oil . 14 6.1 General . 14 6.2 Round wire . 15 6.2.1 Equipment . 15 6.2.2 Specimens . 15 6.2.3 Procedure 15 6.3 Rectangular wire . 16 6.3.1 Equipment . 16 6.3.2 Spe

22、cimens . 16 6.3.3 Procedure 16 Annex A (informative) Alternative refrigerants to monochlorodifluoromethane 18 Bibliography . 19 Figure 1 Pencil and specimen for solvent test . 8 Figure 2 Refrigerant extractable test siphon cup . 10 Figure 3 Condenser coil . 11 Figure 4 Example of carrier for soldera

23、bility test . 14 Table 1 Pencil hardness . 9 Table 2 Volume of components 16 BS EN 60851-4:2016IEC 60851-4:2016 IEC 2016 3 Table A.1 Alternative refrigerants to R 22 . 18 BS EN 60851-4:2016 4 IEC 60851-4:2016 IEC 2016 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ WINDING WIRES TEST METHODS Part 4: Che

24、mical properties FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning stand

25、ardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparati

26、on is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with

27、the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjec

28、ts since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical c

29、ontent of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent pos

30、sible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide confor

31、mity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its direct

32、ors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising

33、out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is draw

34、n to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60851-4 has been prepared by IEC technical committee 55: Winding wires. This third e

35、dition cancels and replaces the second edition published in 1996, Amendment 1:1997 and Amendment 2:2005. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) revision of Test 16: Resistance to refrig

36、erants; b) revision of Test 17: Solderability; c) new Annex A for alternative refrigerants to monochlorodifluoromethane (R 22). BS EN 60851-4:2016IEC 60851-4:2016 IEC 2016 5 The text of this standard is based on the following documents: FDIS Report on voting 55/1578/FDIS 55/1580/RVD Full information

37、 on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all the parts in the IEC 60851 series, published under the general title Winding Wires Te

38、st methods, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will b

39、e reconfirmed, withdrawn, replaced by a revised edition, or amended. BS EN 60851-4:2016 6 IEC 60851-4:2016 IEC 2016 INTRODUCTION The IEC 60851 series is part of a group of International Standards which define insulated wires used for windings in electrical equipment: 1) IEC 60851 series, Winding wir

40、es Test methods; 2) IEC 60317 series, Specifications for particular types of winding wires; 3) IEC 60264 series, Packaging of winding wires. BS EN 60851-4:2016IEC 60851-4:2016 IEC 2016 7 WINDING WIRES TEST METHODS Part 4: Chemical properties 1 Scope This part of IEC 60851 specifies the following che

41、mical properties tests: Test 12: Resistance to solvents; Test 16: Resistance to refrigerants; Test 17: Solderability; Test 20: Resistance to transformer oil. For definitions, general notes on methods of test and the complete series of methods of test for winding wires see IEC 60851-1. 2 Normative re

42、ferences The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies

43、. IEC 60296, Fluids for electrotechnical applications Unused mineral insulating oils for transformers and switchgear IEC 60554-1:1977, Specification for cellulosic papers for electrical purposes Part 1: Definitions and general requirements IEC 60851-1, Winding wires Test methods Part 1: General IEC

44、60851-3:2009, Winding wires Test methods Part 3: Mechanical properties IEC 60851-5:2008, Winding wires Test methods Part 5: Electrical properties ISO 9453, Soft solder alloys Chemical compositions and forms 3 Test 12: Resistance to solvents 3.1 General This test is applicable to enamelled round wire

45、 with a nominal conductor diameter over 0,250 mm and to enamelled rectangular wire. The test is not suitable for round wires with a nominal conductor diameter up to and including 0,250 mm. Resistance to solvents is expressed by the pencil hardness of the wire after solvent treatment. BS EN 60851-4:2

46、016 8 IEC 60851-4:2016 IEC 2016 3.2 Equipment The following solvents shall be used: standard solvent as specified below, or solvent as agreed between purchaser and supplier. The standard solvent shall be a mixture of: 60 % by volume white spirit with maximum aromatic content of 18 %; 30 % by volume

47、xylene; 10 % by volume butanol. The pencil to be used shall be a lead pencil of the hardness specified in the relevant standard. Before each test, the point of the pencil shall be sharpened with a smooth-cut file to form an angle of 60 symmetrical about the axis of the lead according to Figure 1. Ke

48、y 1 Winding wire specimen 2 Pencil 3 Test surface NOTE Angle tolerances 5. Figure 1 Pencil and specimen for solvent test 3.3 Procedure A straight piece of wire, approximately 150 mm in length, shall be preconditioned for (10 1) min at (130 3) C in an oven with forced air circulation. A substantial l

49、ength of the wire shall then be immersed in standard solvent contained in a glass cylinder and shall be maintained therein at a temperature of (60 3) C for a period of (30 3) min. The wire shall IEC 60 60 2 1 3 BS EN 60851-4:2016IEC 60851-4:2016 IEC 2016 9 then be removed from the solvent. The hardness of the wire surface shall then be determined in the following manner within a period of 30 s after removal f