BS EN 60851-2-2009 Winding wires - Test methods - Determination of dimensions《绕组线 试验方法 尺寸规格测定》.pdf

《BS EN 60851-2-2009 Winding wires - Test methods - Determination of dimensions《绕组线 试验方法 尺寸规格测定》.pdf》由会员分享，可在线阅读，更多相关《BS EN 60851-2-2009 Winding wires - Test methods - Determination of dimensions《绕组线 试验方法 尺寸规格测定》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationWinding wires Test methods Part 2: Determination of dimensionsBS EN 60851-2:2009Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/04/2010 03:04, Uncontrolled Copy, (c) BS

2、INational forewordThis British Standard is the UK implementation of EN 60851-2:2009. It isidentical to IEC 60851-2:2009. It supersedes BS EN 60851-2:1998 which iswithdrawn.The UK participation in its preparation was entrusted to Technical CommitteeGEL/55, Winding wires.A list of organizations repres

3、ented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. BSI 2010ISBN 978 0 580 64069 8ICS 29.060.10Compliance with a British Standard cannot confer im

4、munity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 31 January 2010Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 60851-2:2009Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS,

5、13/04/2010 03:04, Uncontrolled Copy, (c) BSIEUROPEAN STANDARD EN 60851-2 NORME EUROPENNE EUROPISCHE NORM December 2009 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat:

6、 Avenue Marnix 17, B - 1000 Brussels 2009 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60851-2:2009 E ICS 29.060.10 Supersedes EN 60851-2:1996 + A1:1997 + A2:2003English version Winding wires - Test methods - Part 2: Determinat

7、ion of dimensions (IEC 60851-2:2009) Fils de bobinage - Mthodes dessai - Partie 2: Dtermination des dimensions (CEI 60851-2:2009) Wickeldrhte - Prfverfahren - Teil 2: Ermittlung der Mae (IEC 60851-2:2009) This European Standard was approved by CENELEC on 2009-11-01. CENELEC members are bound to comp

8、ly with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Sec

9、retariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as

10、 the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,

11、 Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 60851-2:2009Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/04/2010 03:04, Uncontrolled Copy, (c) BSIEN 60851-2:2009 - 2 - Foreword The text of document 55/1144/FDIS, future edition 3 of IEC 60

12、851-2, prepared by IEC TC 55, Winding wires, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60851-2 on 2009-11-01. This European Standard supersedes EN 60851-2:1996 + A1:1997 + A2:2003. Technical revisions of note include recognition of the use of optical micrometer

13、s in determining the dimensions of round and rectangular enamelled wire. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2010-08-01 latest date by which the national standards

14、 conflicting with the EN have to be withdrawn (dow) 2012-11-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60851-2:2009 was approved by CENELEC as a European Standard without any modification. _ BS EN 60851-2:2009Licensed Copy: Wang Bin, ISO/EX

15、CHANGE CHINA STANDARDS, 13/04/2010 03:04, Uncontrolled Copy, (c) BSI- 3 - EN 60851-2:2009 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document.

16、For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publicatio

17、n Year Title EN/HD Year IEC 60851-1 -1)Winding wires - Test methods - Part 1: General EN 60851-1 19962)IEC 60851-5 2008 Winding wires - Test methods - Part 5: Electrical properties EN 60851-5 2008 1)Undated reference. 2)Valid edition at date of issue. BS EN 60851-2:2009Licensed Copy: Wang Bin, ISO/E

18、XCHANGE CHINA STANDARDS, 13/04/2010 03:04, Uncontrolled Copy, (c) BSI 2 60851-2 IEC:2009 CONTENTS INTRODUCTION.5 1 Scope.6 2 Normative references .6 3 Test 4: Dimensions.6 3.1 Equipment.6 3.1.1 Round and rectangular wire.6 3.1.2 Bunched wire.7 3.2 Procedure .7 3.2.1 Conductor dimension.7 3.2.2 Out-o

19、f-roundness of the conductor 7 3.2.3 Rounding of corners of rectangular wire 8 3.2.4 Increase in dimension due to the insulation .8 3.2.5 Overall dimension8 3.2.6 Increase in diameter due to the bonding layer of enamelled round wire .9 Figure 1 Conical mandrel .10 Table 1 Types of winding wires 6 Ta

20、ble 1a Enamelled round wire6 Table 1b All the types of winding wires except enamelled round wire.7 Table 2 Determination of the conductor diameter .9 BS EN 60851-2:2009Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/04/2010 03:04, Uncontrolled Copy, (c) BSI60851-2 IEC:2009 5 INTRODUCTION T

21、his part of IEC 60851 forms an element of a series of standards which deals with insulated wires used for windings in electrical equipment. The series has three groups describing a) methods of test (IEC 60851); b) specifications (IEC 60317); c) packaging (IEC 60264). BS EN 60851-2:2009Licensed Copy:

22、 Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/04/2010 03:04, Uncontrolled Copy, (c) BSI 6 60851-2 IEC:2009 WINDING WIRES TEST METHODS Part 2: Determination of dimensions 1 Scope This part of IEC 60851 specifies the following method of test: Test 4: Dimensions. For definitions, general notes on methods

23、 of test and the complete series of methods of test for winding wires, see IEC 60851-1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition o

24、f the referenced document (including any amendments) applies. IEC 60851-1, Winding wires Test methods Part 1: General IEC 60851-5:2008, Winding wires Test methods Part 5: Electrical properties 3 Test 4: Dimensions 3.1 Equipment 3.1.1 Round and rectangular wire The equipment used shall have a resolut

25、ion of 2 m or less for wires over 0,200 mm and for wires up to and including 0,200 mm, a resolution of 1 m or less. Both mechanical contact and optical non-contact micrometers may be used. If mechanical contact micrometers are used, the ratio of measuring force and anvil diameter shall be in accorda

26、nce with the range as given in Table 1a and Table 1b. The diameter range of the spindle and anvil is also given in Table 1a and Table 1b. If optical micrometers are used, the average of the readings shall be recorded as the diameter of the conductor. If a specific measuring equipment must be used, i

27、t shall be agreed upon between the customer and the supplier. Table 1 Types of winding wires Table 1a Enamelled round wire Type of winding wire Nominal conductor diameter mm Anvil diameter mm Measuring force(N)/anvil diameter(mm) = P(N/mm) Enamelled round wire 0,100 0,100 0,45 2 to 8 5 to 8 5 to 8 0

28、,01 P 0,16 0,16 0,063 mm Resistance Dimension 3 of IEC 60851-5 3.2.1.1 NOTE By agreement between purchaser and supplier, resistance measurements may be made in the range of nominal conductor diameters over 0,063 mm and up to and including 1,000 mm. 3.2.5.2 Rectangular wire On a straight piece of wir

29、e at each of three places at least 100 mm apart, one measurement shall be made of the two dimensions of the wire. Where the dimension of the specimen is greater than the diameter of the micrometer spindle, measurements shall be made both at the centre of the face of the specimen and over the edges.

30、If these values differ, only the highest value shall be noted. The three single values shall be reported for each dimension of the wire. The mean values represent the overall width or the overall thickness respectively. 3.2.5.3 Bunched wire NOTE The method indicated below gives useful values in prac

31、tice, but not an accurate overall diameter. The overall diameter is the width of a layer wound on a mandrel divided by the number of turns. The bunched wire shall be wound closely on a mandrel according to Figure 1 and under a tension in newtons, which is 65 times the total nominal cross-section of

32、the conductors in square millimetres. The width of the layer shall be not less than 10 mm for bunched wires with overall diameters up to and including 0,5 mm, and be not less than 20 mm for larger diameters and shall be measured with a precision of 0,5 mm. One measurement shall be made. The overall

33、diameter rounded off to 0,01 mm shall be reported. 3.2.6 Increase in diameter due to the bonding layer of enamelled round wire The increase in diameter due to the bonding layer is the difference of the overall diameter with and without the bonding layer. The overall diameter of the wire shall be mea

34、sured according to 3.2.5.1. After removal of the bonding layer by means of a solvent or any other suitable agent or by any other method which does not damage the underlying coating, the measurement shall be repeated. The difference of the two mean values shall be reported as the increase in diameter

35、 due to the bonding layer. BS EN 60851-2:2009Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/04/2010 03:04, Uncontrolled Copy, (c) BSI 10 60851-2 IEC:2009 Dimensions in millimetres Cne 1:390 10 60IEC 1842/09 Figure 1 Conical mandrel _ BS EN 60851-2:2009Licensed Copy: Wang Bin, ISO/EXCHANGE

36、 CHINA STANDARDS, 13/04/2010 03:04, Uncontrolled Copy, (c) BSIThis page deliberately left blankLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/04/2010 03:04, Uncontrolled Copy, (c) BSIBSI is the independent national body responsible for preparing British Standardsand other standards-relate

37、d publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9

38、001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccu

39、racy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensu

40、resthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, internatio

41、nal and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless ot

42、herwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on

43、 all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministrati

44、on. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the

45、UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without p

46、rior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/04/2010 03:04, Uncontrolled Copy, (c) BSI