BS EN 60169-23-1994 Radio-frequency connectors - Pin and socket connector for use with 3 5 mm rigid precision coaxial lines with inner diameter of outer conductor 3 5 mm (0 1378 in.pdf

《BS EN 60169-23-1994 Radio-frequency connectors - Pin and socket connector for use with 3 5 mm rigid precision coaxial lines with inner diameter of outer conductor 3 5 mm (0 1378 in.pdf》由会员分享，可在线阅读，更多相关《BS EN 60169-23-1994 Radio-frequency connectors - Pin and socket connector for use with 3 5 mm rigid precision coaxial lines with inner diameter of outer conductor 3 5 mm (0 1378 in.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 60169-23:1994 IEC 169-23:1991 Radio-frequency connectors Part 23: Pin and socket connector for use with3,5mm rigid precision coaxial lines with inner diameter of outer conductor3,5mm (0,1378in) The European Standard EN 60169-23:1993 has the status of a British Standard UDC 621

2、.316.541.029.5/.7BS EN60169-23:1994 This British Standard, having been prepared under the directionof the Electronic Components Standards PolicyCommittee, was publishedunder the authorityofthe Standards Boardand comesinto effect on 15March1994 BSI 01-2000 The following BSI references relate to the w

3、ork on this standard: Committee reference ECL/6 Draft announced in BSI News January1994 ISBN 0 580 22839 8 Cooperating organizations The European Committee for Electrotechnical Standardization (CENELEC), under whose supervision this European Standard was prepared, comprises the national committees o

4、f the following countries: Austria Italy Belgium Luxembourg Denmark Netherlands Finland Norway France Portugal Germany Spain Greece Sweden Iceland Switzerland Ireland United Kingdom Amendments issued since publication Amd. No. Date CommentsBS EN60169-23:1994 BSI 01-2000 i Contents Page Cooperating o

5、rganizations Inside front cover National foreword ii Foreword 2 Text of EN 60169-23 3 National annex NA (informative) Committees responsible Inside back coverBS EN60169-23:1994 ii BSI 01-2000 National foreword This British Standard has been prepared under the direction of the Electronic Components S

6、tandards Policy Committee and is the English language version of EN60169-23:1993 Radio-frequency connectors Part 23: Pin and socket connector for use with3,5mm rigid precision coaxial lines with inner diameter of outer conductor3,5mm (0,1378in), published by the European Committee for Electrotechnic

7、al Standardization (CENELEC). It is identical with IEC169-23:1991 published by the International Electrotechnical Committee(IEC). A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compl

8、iance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theEN title page, pages2 to8, an inside back cover and a back cover. This standard has been updated (see copyright dat

9、e) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN60169-23 September1993 UDC621.316.541.029.5/.7 Descriptors: Radio-frequency connectors pin and socket, rigid coaxial lines English

10、version Radio-frequency connectors Part 23: Pin and socket connector for use with3,5mm rigidprecision coaxial lines with inner diameter of outerconductor3,5mm (0,1378in) (IEC 169-23:1991) Connecteurs pour frquences radiolectriques Vingt-troisime partie: Connecteur mle et femelle pour lignes rigides

11、coaxiales de prcision de3,5mm avec diamtre intrieur du conducteur extrieur de3,5mm (0,1378in) (CEI 169-23:1991) Hochfrequenz-Steckverbindungen Teil 23: Stift- und Buchsen-Stecker fr3,5mm Przisions-Koaxial-Leitungen mit einem Innendurchmesser des Auenleiters von3,5mm (0,1378in) (IEC169-23:1991) This

12、European Standard was approved by CENELEC on1993-07-06. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical refere

13、nces concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC me

14、mber into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Port

15、ugal, Spain, Sweden, Switzerland and UnitedKingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1993 Copyright reserved to CEN

16、ELEC members Ref. No. EN 60169-23:1993 EEN60169-23:1993 BSI 01-2000 2 Foreword The CENELEC questionnaire procedure, performed for finding out whether or not the InternationalStandard IEC169-23:1991 could be accepted without textual changes, has shown that no common modifications were necessary for t

17、he acceptance as European Standard. The reference document was submitted to the CENELEC members for formal vote and was approved by CENELEC as EN 60169-23 on6July1993. The following dates were fixed: For products which have complied with the relevant national standard before1994-08-01, as shown by t

18、he manufacturer or by a certification body, this previous standard may continue to apply for production until1999-08-01. Annexes designated “normative” are part of the body of the standard. In this standard,Annex ZA is normative. Contents Page Foreword 2 Introduction 3 1 Scope 3 2 Dimensions Mating

19、face details for GPC and LPC connectors 3 2.1 Plug connector and contact 3 2.2 Socket connector and contact 4 Annex ZA (normative) Other international publications quoted in this standard with the references of the relevant European publications 7 Figure 1 Plug connector 3 Figure 1a Plug contact 4 F

20、igure 2 Socket connector 4 Figure 2a Socket contact 5 Table 1 Dimensions 6 latest date of publication of an identical national standard (dop) 1994-08-01 latest date of withdrawal of conflicting national standards (dow) 1994-08-01EN60169-23:1993 BSI 01-2000 3 Introduction This standard provides matin

21、g face details for the following two types of connectors: GPC: General Precision Connector Instrument grade (beaded). LPC: Laboratory Precision Connector Instrument grade (beadless). 1 Scope Coaxial line devices and systems are becoming more prevalent at frequencies above18GHz. This standard covers

22、a precision pin and socket connector for use with3,5mm rigid precision coaxial lines so as to minimize test apparatus errors attributable to coaxial connectors. These connectors are constructed so as to affix on the50 7,3,5mm rigid precision coaxial line described in IEC457-5, and to provide low ref

23、lection to34GHz. For mated pairs, a reflection factor of0,003+0,00135f (GHz) is typical for GPC connectors. These connectors may be, and often are, mated with SMA connectors. 2 Dimensions Mating face details for GPC and LPC connectors Original dimensions are in inches. All undimensioned pictorial co

24、nfigurations are for reference purposes only. 2.1 Plug connector and contact Figure 1 Plug connector (for dimensions, seeTable 1 which follows)EN60169-23:1993 4 BSI 01-2000 2.2 Socket connector and contact Figure 1a Plug contact (for dimensions, seeTable 1 which follows) Figure 2 Socket connector (f

25、or dimensions, seeTable 1 which follows)EN60169-23:1993 BSI 01-2000 5 Figure 2a Socket contact (for dimensions, seeTable 1 which follows)EN60169-23:1993 6 BSI 01-2000 Table 1 Dimensions Reference Millimetres (mm) Inches (in) Connector Min. Max. Min. Max. a 2,36 3,56 0,093 0,135 GPC, LPC b 2,29 2,49

26、0,090 0,098 GPC, LPC c 3,43 4,01 0,135 0,158 GPC, LPC d,q 0,000 0,076 0,0000 0,0030 GPC only d,q 0,000 0,013 0,0000 0,0005 LPC only e 6,38 6,73 0,251 0,265 GPC, LPC f 4,547 4,577 0,1790 0,1802 GPC, LPC g 0,03 0,13 0,001 0,005 GPC, LPC h 3,493 3,508 0,1375 0,1381 GPC only h 3,495 3,505 0,1376 0,1380

27、LPC only i 0,919 0,935 0,0362 0,0368 GPC, LPC j 0,15 0,38 0,006 0,015 GPC, LPC k 2,03 2,29 0,080 0,090 GPC only k 2,41 2,67 0,095 0,105 LPC only l 27 33 27 33 GPC only l 20 25 20 25 LPC only m,v 1,514 1,524 0,0596 0,0600 GPC only m,v 1,5161 1,5237 0,05969 0,05999 LPC only n 5,54 0,218 GPC, LPC o 3,3

28、5 4,62 0,132 0,182 GPC, LPC p 0,38 1,14 0,015 0,045 GPC, LPC r 3,493 3,508 0,1375 0,1381 GPC only r 3,495 3,505 0,1376 0,1380 LPC only s 4,597 4,628 0,1810 0,1822 GPC, LPC t 5,28 5,46 0,208 0,215 GPC, LPC u 1,88 1,98 0,074 0,078 GPC, LPC w 2,79 3,18 0,110 0,125 GPC, LPC x 0,08 0,20 0,003 0,008 GPC,

29、LPC y 0,15 0,51 0,006 0,020 GPC, LPC z 0,05 45 0,25 45 0,002 45 0.010 45 GPC, LPC aa 0,38 1,14 0,015 0,045 GPC, LPC NOTE 1Surface roughness 0,63 4m (16 4in). NOTE 2Surface roughness 1,26 4m (32 4in). NOTE 3Socket contact configuration (for example, slotted or slotless) optional; dimensions to meet r

30、eflection factor requirements, mating characteristics and connector durability when mated with a0,919mm to0,935mm (0,0362in to0,0368in) pin. Socket contact shall accept a0,889mm to0,940mm (0,0350in to0,0370in) pin. NOTE 4To the left of dimension W (slotted contacts GPC, LPC).EN60169-23:1993 BSI 01-2

31、000 7 Annex ZA (normative) Other international publications quoted in this standard with the references of the relevant European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate

32、 places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication

33、referred to applies. NOTEWhen the international publication has been modified by CENELEC common modifications, indicated by (mod), the relevant EN/HD applies. IEC publication Date Title EN/HD Date 457-5 1984 Rigid precision coaxial lines and their associated precisionconnectors Part 5:50 ohms3.5mm r

34、igid precision coaxial line withprovision for mounting connectors HD 351.5 S1 19868 blankBS EN60169-23:1994 BSI 01-2000 National annex NA (informative) Committees responsible The United Kingdom participation in the preparation of this European Standard was entrusted by the Electronic Components Stan

35、dards Policy Committee (ECL/-) to Technical Committee ECL/6, upon which the following bodies were represented: British Cable Makers Confederation British Telecommunications plc EEA (the Association of Electronics, Telecommunications and Business Equipment Industries) National Supervising Inspectorat

36、e Society of British Aerospace Companies Limited Telecommunications Cables Group of Bcmc The following bodies were also represented in the drafting of the standard, through subcommittees and panels: AEA Technology Beccama (Beama Electrical Cable Connector and Accessories Manufacturers Association) E

37、lectronic Components Industry Federation Ministry of Defence Society of Cable Television EngineersBS EN 60169-23:1994 IEC 169-23:1991 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents t

38、he UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to imp

39、rove the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:0208

40、9967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:0208996900

41、1. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and inte

42、rnational standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are ke

43、pt up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyri

44、ght, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwis

45、e without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.